Our class that meets at 10AM on Thurs. now has five members and is full.  There is still a chance to join the class but a the meeting is now in the evening.  There have been many questions about balances needed for the class. I prefer all question be made here so that I don't have to say the samething to many people and most importantly, I can remember who I've said what to.

So to reiterated for all:

The balance is the most important piece of equipment for dyeing.  We use it to measure dye, to weigh fibers to check our volumes and other equipment.  You could dye with only a balance  but there is no piece of equipment that can substitue for a balance.  You need a balance that can measure 0.1g accurately, this should be its readability.  A readability of 0.01g is not better it is too sensitive and weighs fingerprints, wind gusts....  The smaller the capacity( the maximum it will weigh) the cheaper the balance.

I reccommended some Acculab balances that has caused some problems since they went out of business in Dec.

We have NO remaining stock on the Acculab VIC-1501. Acculab
is a victim of deleveraging and the brand Acculab has terminated
production on December 31, 2010. The information listed below on the
VIC-1501 is for reference only for those people researching the
specification on a VIC1501 scale they already own.

I see on the table there are two balances listed as #1501 but the one
I think you want is VIC -1501 with a capacity of 1500g (more than 3
lbs.) and a readability of 0.1g.  Here is another source on the net, http://www.affordablescales.com/scales_mfg1.asp?mfgsrch=Qq1009Xyu14b&fl=19&nm=Acculab_Jewelry_Scales that includes the AC adapter and calibration weights. I hope they still have some!

If not check out this one, http://balance.balances.com/scales/742.

What you need is:

  • readability or accuracy of 0.1g   (0.01g is not better, it is too tempermental)
  • tare
  • AC adapter or the ability to run plugged in
  • calibration weights, get the ones recommended

What is optional is the capacity.  The greater the capacity the
higher the cost.  For this class we will be weighing 1 and 5g quantities
mostly.  A capacity of 210g would allow you to weigh about a half of a
pound of fiber, 1500g is over 3lbs.  The larger the mass of the fiber
the less accuracy required, so sometimes two scales are cheaper than
one. 

Anyhow here are some possibilities;

Cathie reccomends  scalesgalore,com, Mary called them and they seem to have a good supply of the Acculab VC 1501

Corina asked:   Regarding the scale I have one bran name Escali  and is 5000g x1g / 200 oz x 0.1 oz
I wandering if it's okay the one I have.

No, this scale will not work to measuring out dye in 1.0g quanties.  It is - or + 1g.  But it will work for measuring out large amounts of fiber so the balance you buy can have a very small capacity and be cheaper.  Examples are : DigiWeigh DW-600BX Pocket Scale, 600x 0.1 g at $29.95 or Ohaus PS121 Pocket Scale , 120x 0.1 g for $35.

A calibration weight is used to determine if the balances is working correctly. 
An AC adapter is so that you can plug the balance into the wall and not run on batteries all the time.  I think that these small scales only run on batteries.  Make sure you have some new ones on hand.

 

Comments

pjdoney (not verified)

I have an old triple beam balance left over from homeschooling my kids.  Then came a scale that measures to 1 gram, followed by a store scale that goes up to 10 pounds (friend's shop closed), and then my husband purchased a digital ProScale XC 500 that weighs up to 500 grams x 0.01g.  I do understand about the "fussiness" that Karren talks about, but do I really need to buy another balance?

http://www.oldwillknottscales.com/ is a place we've ordered goodies from in the past.

Karren K. Brito

People started the study group with a triple beam either gave up completely or bought a digital during the study.  So Triple Beam is out.

A combination others you mentioned might work.  What does one that goes to 1g have as its readability?  Does it have a tare function?  Does it have a weight to calibrate it?  Do you have the manual and know how to calibrate it?

Ditto on the 500gx0.01g scale.  Have you weighed out 1.0g of dye on this scale?  If not , set it up in a place you can use it, calibrate it.  Put a weigh boat of some kind on the scale, tare it and weigh out 0.9g of corn startch or powered sugar. 

Describe to us what happens.

 

 

pjdoney (not verified)

There was a reason after using the triple beam for a couple of years that we went looking for something easier and more portable to use!  The 1 gram scale is not accurate enough since that is actually the readability number.  It was something that we picked up locally and realtively inexpensively.  I used to use it to measure out ounces/ grams of yarn batches for custom dyeing.  My big store scale is accurate to 0.5 grams and it has replaced the previous scale for yarns, rovings, and even fabric.  I will try to find my calibration weights for the 500 x 0.01gram scale.  The room that they are in is stuffed with fibers and all sorts of things, especially as my husband works to finish building the dye studio.  I use this scale all the time to measure out my dye powder to generally make 1% stock solutions, 4 liters at a time.  I shall report back.  Peggy

Karren K. Brito

As I was going over your list for equipment and dyes with what I have, I wanted to ask two questions.
 
1)  I have switched in the last year from Jacquard Acid dyes to Permaset dyes.  I know that you have set up the class for Lanaset saying that we would have a working dye studio when we finish.  Would it be OK for me to use my Permaset in place of the Lanaset?  I have already begun doing more triad studies in order to facilitate my color matching for my business that I love doing.
 
If not, there are several of the Sabraset/ Lanaset colors on the Pro Chem website that I do not know for sure which ones you want for us to have on hand  (Yellow Gold, Red, Green, and Dark Brown).
 
2)  What about citric acid in place of acetic acid?
 
Thank-you for your time and answers.
 

Karren K. Brito

Peggy,

I don't know anything about Permaset Dyes.  Each dye reseller puts their name on the dyes so the same dyes are sold under many names.  Lanaset is the name, Ciba, the manufacturer uses but requires resellers to use different names because they don't want us "spoon dyers" calling up their technical staff.  So ProChem calls them Sabraset. There are a lot fewer dyes than names.  Unless you want to do all the research and find out what dyes Permaset are, for example their CI numbers, and then contact their manufacturer for reccommended procedures,  I would suggest using Lanaset dyes. Lanaset are not just another acid dye, they form much stronger bonds to the fiber.

The colors you need are the colors that are manufacured by Ciba, they are basically all the same molecule and one color. You don't need any colors that are mixes, you can make your own mixes.

How can you tell which colors are the manufactured colors?  Ask your seller, they know. If you look at the ProChem site  and click on a color of Sabraset you may see something like this:

PRO Sun Yellow 180
(Yellow 4G)

or

PRO Spiced Pumpkin 281

The first color, Sun Yellow, is a manufacturered color, hence the offical color designation , Yellow 4G, and Spiced Pumpkin is a color they mixed at ProChem. I think there is a list of the Lanaset dyes you need on the page of things required before the class begins, this page is attached to the bottom of the class page.

Citric acid is not an easy substitute for acetic acid, sometimes it works, sometimes not.  Lanaset dye bath uses a buffer near pH 4.5, to keep the pH nearly constant.  The buffer is made of sodium acetate/acetic acid.  Citric acid will NOT form this buffer at pH 4.5; citric acid can buffer at a lower pH but needs sodium citrate, not sodium acetate.  Keep it simple for now, use acetic acid/sodium acetate buffer.  I will tell you when you don't need the buffer and can easily use just the acid, and you can use what you want as long as you get the correct pH.


pjdoney (not verified)

Permaset dyes from the Standard Dye Company had been recommended to me by another dyer who has used them in her dyeing business.  She said that they were just like Lanasets but less expensive.  I contacted the company and with my questions they sent me back to their lab technicians.  The upshot of my conversation was anything that I read about Lanasets apply to their Permaset dyes.   

Thanks for asnwering the citric acid question too!  I am very interested in the chemistry aspect of this class.

corinaw (not verified)

Hello Karren,

I decided not to do the online class I think that's to advance for me. Perhaps in the future I can take another one. Thank you very much for answered all my questions.

Enjoy the class everyone.!

Corina

 

 

pjdoney (not verified)

In the past when I was measuring for weight, I weighed my sample amount of yarn, then used blind cord to replicate the length.  Of course there were slight variations in the weight of the cut samples.  Has anybody stumbled upon another way to measure beside piling up yarn on the balance boat?

Karren K. Brito

 The first time you have to pile the yarn up on the balance.  But then just make all of them about the same length.  We will weigh each indiviually and that will take care of any variations.

Karren K. Brito

Lexy is joining the evening class and wanted to know if her balance would work.

I also do have a digital scale but it's  500g x0.01g and a 500g calibration weight.

I think that you need a smaller calibration weight, we need the 1-5g part of the range to be accurate. The 500g calibration weight checks the other end of the range.  Do you have the manual for the balance? What does it recommend?  

Since the balance is overly sensitive you'll have to see if it need a protection box, but you can do that at any time with a cardboard box.

Lexy (not verified)

Hi Karen and everyone else!

Karen, I decided to just go ahead and get a new scale, not only for this class but what you say is true. I use a covered dye box with the scale in it and I'm scared to breath (even with the mask on) or accidentally knock the piece of plastic wrap I'm putting the dye powder onto as it shifts so quickly. Drives me insane! I was always told that was better but it has become a bit of a headache for weighing dyes.

For anyone else, here are the list of pure colours from Paula Burch's website: http://www.pburch.net/dyeing/lanasetdyes.shtml

I just need to figure out what I'll be using for my yarn and then I can get to ordering all that I need. I'd love to do roving since I can use the extras once I do my sample book, for nuno felting but I figured I'd compromise and find a yarn that I can use in nuno felting as well.

I'm looking forward to this learning experience!

 

pjdoney (not verified)

My scale wanted a 500 gram calibration weight which we didn't have so I ordered it as well as a 5 gram because of the extreme difference.  My scale has checked out at both ends of the weight spectrum.

Artistry

Just got off weavolution tour with Mary and Peggy . I have a question about what size container would be good for the dye stock solutions. What volume should it be able to hold? Also, I din't see dust/particle masks on the list, that's something we want right?

Artistry

Just got off weavolution tour with Mary and Peggy . I have a question about what size container would be good for the dye stock solutions. What volume should it be able to hold? Also, I din't see dust/particle masks on the list, that's something we want right? (sorry if this posts twice, I'm trying to get the "updated status" shown on the group post)

Karren K. Brito

We'll be making 100ml of stock to start with in the 100ml volumetric flask. You might want to make more later.

Yes, you will need a mask for particulates but these are easily bought at your local hardware store. Same with rubber gloves.

Karren K. Brito

Mary asked how much yarn is needed and if she could use silk.

You may use silk.  Any protien based fiber will work. In the study group they used from 100-150 sample skeins, at 5g each 5g X 150= 750g or around 3 lbs.  I would then want more to dye for a project, but that is your choice. 

The important thing is that it is all identical, same yarn, same preparation.  Different prep, different color.  Just make sure you have plenty on hand before we begin.  You can get very behind waiting for yarn to arrive.

If you are inclined to start making sample skeins, keep them fairly short  so they fit in your jars nicely.  I have been using skeins with 1/2yd circumfrence.  Tie the skeins with loose figure 8 ties; the finer the yarn  the more ties required to keep tangling to a minimum.  Each skein will need to be labeled while in the dyebath.  You can use pieces of Tyvek or little cable ties.  I measure the weight and lenght of one skein then try to make the others similar but no need for a fuss; we will weigh each skein.

sroph (not verified)

Hi Karren, Do you have any recommendations for sources to purchase the yarn for the class? Or what type or weight yarn you would recommend? Thank you, Sharon

sroph (not verified)

Hi Karren, Do you have any recommendations for sources to purchase the yarn for the class? Or what type or weight yarn you would recommend? Thank you, Sharon

Karren K. Brito

Your choice.  I would recommend a 100% fiber unless you have a reason for doing a mix.  Colors can separate on a mix and complicate your life a bit.  First time keep it simple.

Wool and silk are the most common, wool being cheaper usually. The best choice is the yarn you use the most often; you will then have samples of the yarn you use.  Odd lots are not a good choice in my mind, unless you can get a lot of it now. 

When I have color samples on merino wool but I want to dye 50% alpaca 50%merino the first thing I do is dye both together the wool and the mix in a pale neutral color.  From the differences in the colors I can extrapolate to the other samples to formulate.  So I need to have some of the orginal yarn around.

What kind of weaving do you do?  Do you do tapestry, rugs, throws, fashion?

Karren K. Brito

Now we have 5 people registered for the class, 3 for the morning; Mary, Cathie and Peggy and 2 for the evening one, Ximena and Sharon.

By next Thurs., one week before the class starts, I would like you to post here some info:

what fiber you plan to usewhat balance you have , capacity, readability and if you calibrated ita picture of your dye bath set upanother pic of your Munsell book and other things you have ready to go

We are  practicing taking and posting pics in case you wondered.  This is an important part of showing understanding what you are doing and the best way to trouble shoot.

Cathie I need you to PM your telephone #.  If there is any trouble with Webex, or the internet I'd like  to have another way to contact you. I think I have everyone elses.

Do you all have your materials to start?

pjdoney (not verified)

I ordered last week the auxilaries, a couple of dyes, and some soy wax for batik from Pro Chem.  I know it has shipped and expect it this week.  We have painted the dye studio and put up color correct lights so I can work in the evenings out there soon.  I plan on taking a picture of it once it's a little cleaner (ahem) to practice the picture posting.  Sixty-two skeins are ready, 10 more measured, and the yarn swift full of yarn to do it all over again!

Blessings,

Peggy

Artistry

Can the canning jars rest directly on the bottom of the pot( in a water bath) over the heat without cracking? Do I need something to rest the jars on so they don't come in contact with the bottom of the pot?

pjdoney (not verified)

Cathie, I put old towels down in the bottom of my pots for the jars to rest on.

Karren K. Brito

I don't use anything now.  The jars do rattle around and make noise, bubbles from under the jars, I think.  I have used the wire inserts that sometimes come with the enamel canning pots. They work great.  I've never tried old towels but sure have plenty to try.

Artistry

Here is my dye set up

Here is my scale  

here are my dyes and auxillaries    

 

Artistry

I will be using 8/2 silk. I have 101 skeins wound and some more to go. I'll have lots left over for a project! My scale is a Acculab Vic 1501, capacity 1500 grams, readibility 0.1 gr. calibrated to 200 grams( manufacture recommended) but have a 5 gram weight on the way too. I have the book just didn't take a picture of it.

Artistry

Oh, and I'm working outside, good ventilation!

Submitted by Anonymous (not verified) on