I have never run into this before and cannot figure out what I'm doing!  My warp started getting tighter and tighter on one edge and, as I examined the situation,  it looked as if one side had kept "spreading out" a bit and was wound tighter than the rest of it because it was not on top of the previous turns.  I re-beamed, used paper in between the turns and am hoping this will resolve it.  I had to take a partially-woven scarf off. (well, I can make a purse out of it)  and start over.  That side does keep trying to spread itself.  Very odd. The warp is perfectly-centered.  I even got out the measuring-tape to check.

Any ideas?

Nancy C.

Comments

claudia (not verified)

Hi Nancy,

I have been considering what could be causing your problems and a couple things crossed my mind. Are the heddles clear of each other and able to move freely as the warp is advanced? I have a few times found an errant warp thread that was caught on something in the shaft and it was preventing the warp from moving correctly. I would also check the cloth beam and see if everything is free to move there, nothing cathching where the warp is tied or lashed in front.

I hope this helps. Get a good light down inside the shafts and heddles and make sure it not in there. I'll keep thinking. It's happened to me before and I know how annoying this can be.

Claudia

Ellen (not verified)

I have a few times found that the tie on bar was not centered and got stuck against a side, which would pull the whole thing uneven. Just a thought. ?  It is so frustrating to have something happen you can't figure out. Sometimes it could be a help to have another weaver to stand beside or behind the loom while you weave to spot where something doesn't behave right. Alas seldom possible.

Good luck to you!

Guiding Myth (not verified)

 Hi Nancy,

You have done an excellent job figuring out the problem and coming up with the answer.  The paper should help.  What you are experiencing is common when the warp is beamed without heavy paper or sticks.  The "fix" is to beam with heavy paper between all of the layers - or to use lots of sticks.  When you beam without heavy paper or sticks the warp threads on the edge tend to slid off and wind on the beam rather than layer over the previous threads.  As you observed.  I don't know why it happened on one side but not the other.  It could be that the tension when winding on was slightly different on one side.  If it never happened before - well you were either lucky or (there are so many variables)...the yarn is different, the warp is longer this time, when you beamed the warp you used less tension.  

Centering the warp would have no effect.  I have to admit that I often misjudge regarding centering - as long as its not so bad as to make weaving uncomfortable - so what!

Just make sure the paper you use is heavy 60 lb or better.  Some people use rolls of cardboard.

The important thing is that you are on the right track!

S. Stanley

 

dteaj (not verified)

Paper and sticks are really useful. Another possibility: was the winding on tension the same on both sides? Using a warping valet and equal weights on each warp chain can help with this...

Debbie

Ellen (not verified)

I started out using paper and sticks when I learned to weave.

But many years ago I switched to using this fortified heavy plastic that people use to cover their trailers with, cut into strips of the width I need. and normally 3 to 4 meters long. This works wonderfully and is so much easier to use, I think, and I have seen a lot of weavers use it here in denmark. Just an Idea.

I don't know what it is called in America, but I'm sure something like it must be around.

Woolwench (not verified)

I came to this site looking for help with this very same problem. The side threads were getting tighter and tighter as I progressed. I cut off the weaving (sigh) and rewound the warp with sticks. All better :-) Learning curve.

lkautio (not verified)

If the paper and rebeaming didn't work, and you have a folding loom check whether one side is not fully extended or is out of square.  I've seen this happen on a variety of looms.

Laurie Autio

Joanne Hall

If this is an X frame loom, check to see that both sides are extended the full length.  Measure from the breast beam to the back beam on both sides.

Joanne

Submitted by Anonymous (not verified) on