Hi,

This is my first time writing on a forum.  I have a Harrisville Shetland Wool Warp that I sized on the loom.  The yarns all stuck together.  I succeeded in separating them.  The problem I have is that it is hard to beat.  Is it normal or did I put too much sizing on my warp?  I am making a scarf in huck lace for a contest and I really need help with this.  Thanks in advance.

 

 

 

Comments

Claudia Segal (not verified)

I am glad you wrote about this challenge.  It's hard to tell if there is too much sizing the first question that comes to mind is what is the sett and how tightly do you have the warp threads in the reed?  Do you have any pictures you can share?   What did you use to size the yarns?

If you have more than 2 ends in each slot of your reed I would suggest you re-sley the reed using a wider one so you can put 1/slot.  

For help with adding pictures to your comments take a look HERE.  There are other help topics in the Help section.  

Claudia

sally orgren

I know now is too late to mention this, but typically you don't need to size Harrisville Shetland wool.

Claudia is on the money with her sett question.

If you want a drapable scarf, I also wouldn't beat this material the same way I would beat 5/2 cotton for a table runner. I would have a bit of a lighter hand with it.

1gardenia (not verified)

I have used gelatin sizing and a size 15 reed sleyed 1 per dent.  I can't put pictures right now because my camera is not working properly.  I followed a course awhile ago and I used Harrisville Shetland Wool.  It used to break.  That is why I decided to use sizing.  If I change the size of my reed to a 12, the width of my scarf would be too large and would not meet with the contest rules.  I'll try starting over and putting less sizing to see if that will work.  When my camera is ok, I will try put a picture on the site.

Claudia Segal (not verified)

If you are starting over, try using less tension on the warp while weaving and less sizing on the yarn and see if those things help.

No worries about the pictures.  It's just extra input.  Good luck.

Claudia

TNWEAVE (not verified)

I have a Harrisville Loom and just finished a wool scraf. I used a 12 dent reed and sleyed 1 per dent. Once I opened the shed and loosen the threads with my hand about 3 or 4 time during weaving, I found that the sticking went away and I beat twice and weaving turned out nice. Used 3 ply New Zealand Wool.

debmcclintock

When you size your yarn the 2nd time around:-treadle your first tabby and place a weaving sword or pickup stick to hold the yarns apart (a yardstick will work also) -Apply the sizing to the top layer.  Wait for it to dry.  -Treadle the second tabby and place a weaving sword or pickup stick to hold the yarns apart-Apply the sizing to the top layer.  Wait for it to dry.that way alternate threads will have sizing and have time to dry separately and not get stuck...make sense?

sally orgren

Okay, a few more thoughts...

At 15 epi, you are at the tightest sett recommended for Harrisville Shetland weaving a twill (or something with lots of floats, like a huck). If your design has just a few Huck blocks and is mostly plain weave areas, you may need to open up your sett from 15. That might mean some slight redesigning, as you would need to drop off ends on either side of the scarf to keep to your "contest" width. (And you want to make sure where you planned the huck blocks still worked in your revised design.)

If you have an all-over huck design planned and think 15 epi is the correct sett, the next thing I would do is replace the 15 dent reed with a bigger dent reed (like a 10). You will keep the same total "contest" width, but will just need to resley in the new dent. I think this will give your threads more room to move around when the shed changes and you are beating the new weft to the fell line. It's always better to have thread against thread, than thread against metal. 

For a 10 dent reed, the sley order would be (1,2,1,2,1,2,1,2,1,2) etc.

Another thought... If this fiber was breaking, how old is your wool? Was it compromised by moths, mice, or sun damage if it has been sitting on a shelf for a while? This is typically a pretty sturdy, reliable yarn, so the fact that it was breaking enough for you to consider using sizing is surprising.

Please let us know what you decide to do next. We all have gone through these kind of projects—the hope is by posting we can help someone else in the same pickle!

1gardenia (not verified)

First, I would like to thank everyone for your tips.

I have retied my warp with the same reed.  I did size it but not as much as the first time.  The next time I roll it and size it, I will try DEBMCCLINTOCK tip.  For now, everything looks good.  I am able to keep a balance weave so far.  Also, I'm using less tension.

Yes my yarn is a couple of years old, but it used to break when I bought it. 

In my group, they are also weaving a scarf but with alpaca.  I will be able to help them with all your advice.  Like I said before,  I will posting a picture of my project when my camera is working.  Thanks again.

Chantal

debmcclintock

Chantal, I learned that trick from my Lao teachers.  They wove silk at about 90 epi and sized their silk with rice paste.  Very drippy but the treadle and separate works very well!  Good luck

Submitted by Anonymous (not verified) on