I'm in the process of weaving a scarf of 8/2 Tencel using Huck lace and plain weave.  (The pattern is from Handwoven magazine.)  My question has to do with the first and last two warp ends.  The weft is not laying "flat" after I finish beating the pick -- it either sticks up or down, resulting in a ridge along the edges of the material.  I have to give the weft thread a little tug to get it to lay flat.  What am I doing wrong?  Or is this a common occurrence?  Would a floating selvedge take care of this?

Thanks so much for your help,

Monica

Comments

sally orgren

A photo would be great if you can post one! I am assuming the edges are plain weave, the Huck doesn't go all the way to the edge of the piece?

I am thinking if the little tug on the weft works, that is okay. But look for a way to incorporate that into your throw, not a separate step. My guess is when you start throwing the shuttle a lot, you'll get the hang of this without this minor adjustment that seems to be slowing you down.

I *suspect* on a narrow warp, this might happen more often because you don't have a comfortable width to throw the shuttle at a force that would automatically tug that little bit down. I don't think a selvedge thread would help in this instance. (However, if the Huck areas occur at the selvedge of the scarf, I WOULD add a floating selvedge thread.)

Perhaps practicing the timing of your treadling sequence might help — the throw, changing/closing the shed, and when you actually beat (and hopefully not double-beat!)

Sitting at the computer, I am trying to envision my technique. I believe at the end of my throw, I change the shed and pull the beater toward me about the same time. I give a slight flick of my hand holding the shuttle at the end of the throw (backward, away from the loom) as all this is happening, so that serves to pull down that little bit at the end. I don't set the shuttle down on the fabric after each throw, and I don't want this slight flick to happen when the shed is open, because I don't want to pull on the weft all the way across the warp, just at the last few strings.

I am assuming you are weaving on a floor loom? If not, table looms present a whole different set of issues, and you may need to tug on a table loom weft after every shot. With many table looms, you are forced to put down the shuttle between picks to change the shafts. They are slower weaving by their very nature, but have their advantages, too. (I should know, I own more table looms than floor looms!) 

Have you posted this to the projects yet? If not, please consider doing so, as we'd love to see it. Tencel is great to work with!

laurafry

If you're interested I have video clips on You Tube - my account name is LauraAnnFry1

Click on the "more" and scroll down for the shuttle throwing clips.

Cheers,

Laura

Bonnie Datta (not verified)

It is amazing how many weaving problems are solved by routinely using a temple.  Just this past week I had proof positive of the benefits.  I'm not lecturing you here -- but this is a good opportunity to tell my story.

I have a very fine singles linen warp on the loom, sett at 36 epi.  I had woven 4 dishtowels 26" wide, hemp weft, with a temple, and the edges came out beautifully.  I then narrowed the warp to 15" and (duh) found I didn't have a small enough temple.  But I thought that for a few little squares of cloth I could get by.  I could see immediately that the selvedges were pulling in so I compensated by increasing the angle of the weft.  I kept increasing until I started to get bubbles of weft in the web, but still the selvedges were pulling in about 1/4".  Within 4" of weaving I had broken selvedges on both sides.

I fashioned one of the home-made temples, but it didn't work as this linen/hemp combination is just too unforgiving.  So I made more warp, enough to bring the width out to the size of my smallest temple, threaded it in and weighted it off the back beam.

Now with the temple in place I am back to the usual angle of weft insertion and my selvedges don't budge when I pull the beater.  And even this fine singles linen is again holding up as a selvedge thread.

There is a lesson there!

Bonnie.

Joanne Hall

Hi Monica,

You have received advice from three expert weavers.  Let us know how applying this information helps you.  The only thing I can add is that many looms give you a shed that is too big.  Press more lightly on the treadle, or put something under it to stop it when the shed is big enough.  Better yet, if the treadle cords can be lengthened, make them a little longer.  Then you can tighten your warp tension a little more.  That might also help.  Do try the temple if you are not using one.  If you want more temple information, go to our weaving FAQ at:

http://glimakrausa.com/faq.html

Joanne

Monica Bellas (not verified)

Thanks for the help, everyone.  A picture of the problem wouldn't help, as the scarf is black and the edges don't show up well.  I've not used a temple before, but will definitely take a look at the web addresses that have been posted.  There's plain weave at the edges of the scarf.  I seem to recall having a similar problem on a table loom; I'm now weaving on a floor loom.  I'm in the process of getting another warp ready for the same pattern (different color this time) and will let you all know how it's going.

Thanks again,

Monica

Submitted by Anonymous (not verified) on