I'm weaving on a 72-year-old loom with cloth aprons. The terminal loops (on both ends) holding the front apron rod have finally frayed and in some cases have torn altogether.  I MUST DO SOMETHING. My inclination is to cut new loops, attaching them with handstitching without disturbing the apron.  Removing the entire apron and using the sewing machine to attach the loops has its appeal, too. But (perhaps needlessy), I dread the prospect of having to reattach the apron. I worry about not getting it attached properly and being plagued with tension issues, etc.  Or should I think about replacing the cloth apron with something else altogether? If anyone has walked this ground before, I'd welcome your advice.  Perhaps I'm making a big deal out of what will turn out to be a simple repair, but I thought I'd throw it out to the wisdom of Weavolution. 

 

Many thanks,

Lisa Marty

Comments

Bonnie Datta (not verified)

I had just the situation you describe on my 60" loom.  You might want to test the existing apron as the fabric might be weak.  If it seems OK then:

1. Pull the apron over the front beam and take the rod out.

2. Mark a fold line 3" in from the edge of the existing hem.

3. Fold along that line towards the front beam.

4. Mark a fold line 2" from that fold.

5. Fold along that line towards the back beam.  There is a zig-zag pleat in the apron.

6. Pin securely, ensuring that the edges are straight on the grain of the canvas.

7. Hand sew with small diagonal stitches along the full width through three layers. (This is the hard part.)

8. Clip new rod access holes, trim off the old hem, re-insert the rod.

Here's how mine looks:

It works and I think it was less trouble than taking the apron off -- like you I was worried about getting it back on properly.  Also I didn't think my sewing machine would handle the seam.

Bonnie.

 

 

lisamarty (not verified)

Bonnie,

What an ingenious solution! And thanks for the photo. I don't seem to have a zig-zag pleat on my apron. Any problems with fraying of the clipped rod-access holes?

Thanks so much!

Lisa

Bonnie Datta (not verified)

Hi Lisa.  I meant that after you do the two folds there will be a zig zag pleat -- you can see it in the photo.  No there is no problem with the clipped holes -- that is how it was done originally on my apron.

Glad if this helped.

Bonnie.

 

Michael White

Lisa, replacing a cloth apron is no big thing. Cheryl's 48 inch Macomber had tapes, she wanted an apron. I got some heavy canvas (duck cloth, drill, sailcloth) made a triple fold and stitched this with three rows of stitching. I then (starting from the center) marked off every one inch and cut a 1/2 inch notch. I drew a line on the roller and stapled the apron to it. The size of the apron was such that it went from the roller to the back of the heddles. The only change I had to make was to make the notchs wider. Cheryl uses a 1/2" flat tube and not a rod (the flat stock will not bend)

Have fun

Michael

lisamarty (not verified)

Thanks to Bonnie and Michael for your good ideas! Bonnie, thanks for clarifying "zig-zag pleat" (what a difference a verb tense makes!). And Michael, I wondered if I was being needlessly shy of replacing the whole darn thing. Stapling sounds quick and easy!

clgy (not verified)

My new to me loom has an apron on the cloth beam. I have removed the sectional pieces from the warp beam, am thinking about sewing a new apron for that out of duck cloth. I can sort of use the cloth beam apron as a template. If it works well, I may replace the cloth beam apron also. 

My questions:

If the duck cloth is 45 inches wide, and I use the selvedges on the beam, then I will need about 45 inches for the length of fabric also (for my 45 inch Nilus LeClerc). I plan to serge the ends. If I have 45 inches in width of fabric, is that going to make a long enough apron, both on front and back beams? The "hem", of course, will take up about 6 inches. 

Can I use oak dowel rods instead of metal? Mine are quite rusty and I would need at least one more anyway. 

Also, what direction should these aprons rotate around the beam? In the front, I know the apron comes over the top of the cloth beam, toward me, and up and over the breast beam, heading back flat toward the reed. In the back, is it exactly reversed?

The person who attached my current apron wrapped it all the way around the beam, stapling once to get it on, then wrapping around and stapling again, so that the beam is sort of enclosed in a casing. Is that the usual way to do it?

Thanks!

Cindy

 

laurafry

You need the apron long enough to allow the rod over which the loops are attached to reach within about 6 inches of the heddles.  Measure from the beam up over the back beam to the heddles, then add enough for hems and attaching to the beam.  My apron isn't stapled twice, but it is long enough to go once around the beam (nearly) and still reach the heddles.

cheers,

Laura

clgy (not verified)

Hi Laura! I have an idea for making a new back apron and I wanted to run it past you. You have responded so thoughtfully to a few of my other questions. I hope I can explain this clearly so you can let me know whether my idea makes any sense. Here's what I'm thinking:

The sectional pieces that I removed were originally attached to the beam with 3 screws each. What if I purchased a flat piece of wood, drilling 3 holes at the same intervals, and then make an apron with a hem and insert this long flat piece into it. (Or rather, instead of a hem, some tabs, like tab curtains, so that I can screw the long piece of wood into those same 3 holes on the beam, and also have places to lace one apron rod to the other.) This way, I wouldn't have to make staple holes or nail holes all over the beam, I would know the apron was on tight and straight, and it could be easily removed any time for washing, or if I put it on backwards (!) or if I wanted to remove the apron and try the sectional warping again at some point.

Does this make sense? It seems "nice and neat" to me, but I don't know if the 1/4 inch width of the long flat piece of wood would hurt anything, or if I'm missing something else that might make it a problem.

Thanks for any advice! :)

I do know that I can also check to see if those holes go all the way through the beam, and if they do, perhaps I can figure out how to forget the apron and add the 3 strongs to the beam that hold an apron rod instead. I am not completely clear on how that would work and I don't mind making an apron, so I may just do that. I was also thinking that maybe the purpose of the apron is to have less yarn waste, since the cloth sort of substitutes for yarn and gets you closer to the heddles. Is that right?  

Cindy

 

laurafry

Some people prefer the string loops, others prefer the apron.  I find I like the apron. 

Your plan sounds workable.  I'd say to go ahead and do it.

cheers,

Laura

clgy (not verified)

Thanks Laura. I do like the idea of an apron, and I think I understand how it works a little bit more than I understand how to attach the loops, even though it takes longer to prepare. So I'll probably go with that. If it's successful maybe I can replace the front apron eventually too. 

Cindy

 

Submitted by Anonymous (not verified) on