Hi, my name is nikolas and I just built a  24 in 16 shaft table loom and am now looking for plans for a countermarch loom. Does anyone know where I could find plans for a countermarch loom?

In a previous thread some mentioned that there was an addendum to the edward worst book "how to build a loom" that included 2 plans for countermarch looms. does anyone know where I could find this? I've had no luck searching online.

Thank you so much for your help.

Nikolas

Comments

Joanne Hall

Just find someone in your area who has a countermarch loom and visit them.  Take your camera, measure it and copy it.  The new looms are better than those made from plans that you would find that are old.  Some of the older countermarch types did not work very well and are not made any more.

Joanne

steve104c (not verified)

nikolas, At one time I was going to build may own countermarch loom. Priced the hardware and wood, over $800.00. Got on weavolution and asked questions. Michael from Atlanta contacted me and said he knew of someone selling a loom. I ended up with a Glimakra Standard for $500.00. Had to strip, sand and refinish it, which cost about $35.00 for stripper and shellac. This loom has over 200 pieces. Unless your are set on building your own loom,check around for a used loom you can fix back to new. But if not, Joanne is right about finding someone with a loom you like and taking pics. and measurements. I am a woodworker with all the tools to make anything. A loom design is very basic. Hasn't changed in hundreds of years. In fact my wife wants me to make her a small loom she can sit in her lap and use. Already have an idea, not just a frame but will have 4 harneses, a warp and fabric beam. Good luck.........Steve

whiteoakgrandmother (not verified)

Something else to keep in mind. Joanne clued me in that I can convert my old counterbalance Glimakra Standard to a countermarche, by purchasing the unit for the top of the loom. You can find good deals on counterbalance looms and some may be convertible.

Claudia Segal (not verified)

Depending on where you live, there is someone on Weavolution selling or trading a Bergman loom.  It's a beauty and well worth the $1000 or trade for a smaller loom, etc.

The ad is here.  

Joanne Hall

Please note that the G H part of the diagram has cords much too short to give you any shed.  This V shaped cord must be much longer to allow for the shafts to rise and separate from each other.  Also, the lower lamms, called the balance lamms, need to heavy enough to balance the weight of the shafts.  So, they either need to be longer or taller (not thicker), or both. There may be other things that need to be considered.  I only took a quick look at it.

Joanne

 

yukon (not verified)

Hi Nicholas,

If you are in the area of North Jersey, I'd be happy to show you my Glimakra Standard Countermarch loom.

Margaret

 

johnorr (not verified)

I found these plans on the University of Arizona website. This is a project I want to build but I have no place, in my home, to put it. The garage might be the only place really.

Build Your Loom

ReedGuy

You'll find those plans incomplete in the last link given. I've looked at those partial plans to, but if you look at the modern looms you'll probably find them more elegant and not really very complicated. You will most likely be wanting access to a drill press, table saw and a wood lathe. And maybe even a plane (two) for concave/convex curves for a hand made handrail and beater race.

 

A for instance with those plans: what about the lamms? Then another vital piece of information is the fact that the holes in the treadles must line up vertically with the lamms and centred with the loom frame. Lamms, shafts and treadles all have to be ballanced as well (weight). These little details, and lack of knowledge there of, will give you frustration. ;)

Submitted by Anonymous (not verified) on