I am trying to restore a Tools of the Trade table loom that was part of a college weaving program and, as such, was not treated all that gently.  I have begun taking it apart, sanding and refinishing, but need some help at this point.  I am hoping that someone has one of these looms and can post some photos and answer some hardware questions.

Even before I took the loom partially apart, there were some nuts and bolts missing, and some of the bolts/screws appear to have been replaced without matching them to the originals.  If possible, can anyone who owns one of these looms tell me if all the bolts extending to the inside are the same length?  Also, which bolts are inserted with the heads to the outside of the loom and which to the inside?  Which have wing nuts and which have regular nuts?

On this loom, which has apparently been taken apart and put back together at least once, the pieces that allow the front and back beam to fold are installed on the inside of the castle for the front beam and the outside of the castle for the back beam?  Is this how it is supposed to be?  I found a photo on Daryl's blog (I think) that shows the front beam arrangement and that matches how it is on this loom, but cant see the back beam.

 

I thought this was going to be easy.  HAH  I will attach some photos of what I have here.  ETA:  could only post one photo.

 

Thanks for any help you can provide.


Gail

Comments

sally orgren

Please search under the weaving forum topics/threads here at Weavolution.
Someone else is retooling one of these looms too, and we have been posting photos.

Look at "TOTT questions" and "tools of the trade loom"

Once you take a peek at these images and can upload images of your problem areas, perhaps we can proceed with specifics. (Most of the photos uploaded previously were for the floor loom model.)

Hope that helps get you started. They are great looms and don't come up for sale very often because folks hang onto them, and if there is a hint in the wind that someone is wanting to get rid of one, it usually gets snatched up before it can be advertised!

gailc

Thank you, I have done that.  But, as you wrote, most of the photos and posts were for the floor loom.  I figured out how to post more photos.

 As you can see, the jointed pieces that allow the beams to fold are currently on the inside of the beam attachment for the front beam, but on the outside for the back beam.  That seems strange to me and I would like to know if I should place the pieces inside for the back beam as well.

 

Thanks.

 

Gail

Daryl (not verified)

 Oh my heart is bleeding, this poor loom.  Thanks for taking the time to refurbish it, you won't be sorry.  You have most of it correct, I have the same loom, except sadly a four shaft version, I'd dearly love an eight or twelve and mine is basically the way I purchased it.  The only place where the loom has wing nuts is behind the beater bar that slides up and down to hold the reed, and the four folding side supports.  The front folding side support wing nuts are facing towards the inside of the loom, otherwise they would be in the way of the beater, and the rear folding side support wing nuts are facing towards the outside of the loom, easier to reach.  It looks like they are backwards in your photos.  The bolts that hold the front and back beam side supports, on my loom, are capped with a hex nut, the kind that has a silicone core.  Grips better.

The little short screws that hold the base to the castle walls have little tiny hex nuts, and the screw sticks past the nut.  They are forever needing tightening.  The screws that hold the leather handle on the top, assuming your loom has one, are also held with the same little nut.  They are always needing tightening as well.  I did have to eventually replace the cotton clothesline cord that lifted the shafts, with texsolv, so far so good.

I hope this helps.  You can email me personally if you have any more questions, [email protected] 

Daryl Lancaster

gailc

Finally, this loom is reassembled.  Missing hardware was replaced, pieces that were incorrectly installed have been put where they belong, the wood was sanded and finished with several coats of Watco oil.  The filthy aprons were removed and replaced with new, clean cords.  It looks like a completely different loom.  I used it in a workshop, everything worked fine for me and it is ready to head to its new home.

I am very pleased with how it turned out. 

Daryl (not verified)

Holy Cow Gail!  It is gorgeous.  What a job you did.  I'd be honored to bring it into my house of TOTT looms!

sally orgren

Sounds like a TOTT loom in need of rescue at a great price!

8S, 57" in Franklin Lakes, NJ. Asking $100. Here's the link...(no, I am not the seller, it just crossed my desk and I am passing it along to our little TOTT group here. They are great looms, and they don't come up that often for resale!)

http://newjersey.craigslist.org/fuo/2038995163.html

Equiart (not verified)

I have a 32" 4 harness TOTT floor loom and love it.  Am looking for a table loom to take to the MAFA conference this summer.  How many harnesses does your loom have?  What is the weaving width?  Contact me please at [email protected]

Suzannaski

Hi!

I'll start by apologizing. I'm having trouble with the forums, I don't have permission to make a new post. Also, when I use the search, I get nothing, so I am using google to find things here. 

I will be taking my first weaving class in a few months, but I stumbled across a loom and I bought it, knowing nothing. I have figured out it is the same one as Gail has posted.  Mine needs a good cleaning, and maybe a part or two. And probably new finish (thank you for posting about Watco Oil)

There is no shuttle, I don't know what else I may be missing. How do I know if all the hettles (the metal pins that lift the yarn in each sliding frame?) are there? 

I will start by cleaning, but any help is appreciated. I look forward to learning this fascinating art! Thanks. 

Submitted by gailc on