Here are some suggestions for places to tie up the far end of your backstrap loom.

                                

Lash the end bar to a piece of furniture-                            Use cord to tie the bar to a door knob or hook. Having notches

in this case a bed.                                                                  in the bar will help stop the cord from sliding in toward the warp.

                                                                                                    The loom does tend to tip from side to side with this tie up and for

                                                                                                    that reason, I don't particularly  like it., Weavers in Guatemala use

                                                                                                    it all the time though.

                                                             

Tie the end bar around the broad leg                                                             Use clamps on a table behind which to lodge the

of a piece of furniture.                                                                                        end bar.

                                                  

Put hooks in the side of a heavy piece of furniture.              Another clever way-tied to a chair-convenient foot rest. As the

Your end bar can sit in there.                                                    weaving progresses and you roll it up, you will need to tie 

                                                                                                        longer cord to the far loom bar and attach that to the chair.

                                                                                                        (Thanks to Francorios for that tip!)

                                                                                                       

OTHER SUGGESTIONS............Tie up to stair rails, porch rails, your floor loom if you have one.

 

Comments

raggyb (not verified)

The chair /footrest works great - thanks Aunt Janet!

I was able to use a wooden folding chair with a slat back - so I have the option of folding up the whole set up if I want - although the chair seat sure makes a good storage space for weaving in progress!

bolivian warmi

Kindly posted by Helvetican on another thread....

Mostly I weave bags and straps on the backstrap.  I have woven pillow covers and a poncho, but I usually use the backstrap when I want a warp face fabric that is either too long or too wide for an inkle loom.  I like to make bags that have stripes of inkle type patterning, with a strap that matches one of the stripes.  I have done some experiments with weft faced fabrics, but this is much easier on the floor loom or the rigid heddle.  I'll try to send pictures at a later date - I don't have easy access to older photos, and my daughter is gone for the summer with my camera. 

I am going to try to upload a couple of drawings I made to illustrate a couple of other tips.  These both concern supports for tying the loom to.  My most used and favorite is one I made by attaching hooks on the backside of a doorframe.  I have a long rod (a tool handle from the hardware store, but a broomstick will also work) in which I have drilled two holes near the ends.  I have a doubled length of strong nylon cord going from one end of the stick to the other, much as you put a cord on a stick heddle.  This cord prevents the rod from unexpectedly slipping out of the hooks when the loom is in use.  I have three sets of hooks.  I usually begin a weaving with the bar set high, and lower it as the weaving proceeds.  I like to weave in an open doorway because I don't like to weave with my face against a wall.

The second illustration shows what I do when I want to weave at a friend's house or in a different doorway.  Simply place a chair in the doorway with its back facing you.  Slip the loop of the holding cord over the back of the chair to prevent the rod from rolling or sliding.  The chair only provides a support for the height.  In both of these systems, the rod is supported by the tension of the loom against the back of the door frame.  Its good to wrap a little of that no-skid shelf liner around the ends of the rod to prevent it from marring the door frame.

 

I don't know if I made it clear that both of these illustrations are shown from the side of the doorway away from the direction you are facing - in other words you are in the other room.

carinefile (not verified)

an idea to hang your weaving.
two elastic hair to suspend the work without having to undo.

 

bolivian warmi

Great idea! I wish I could do that. My cat would have it down in the middle of the night! That's a very nice looking warp!

carinefile (not verified)

I have four cats, they do not touch. I cover it with a shawl.
I have a cat who likes to make his own weaving.
Thank you, I watch as soon as I finished the project.

Submitted by bolivian warmi on