I am a very new weaver and have just taken my first project (a handspun scarf) off my jack loom. I am now setting up my warp for a dishtowel project and typical of me, am thinking of alternative ways to do things.

I learned to dress front to back, cutting both ends of my warp bundle...the front gets tied to the breast beam while threading the reed and heddles, then the back gets tied and wound onto the warp beam, then the front ends get tied to the fabric beam.

What my idea is: instead of cutting both ends of  my warp, cut the end that will be going through the reed and heddles but on the other end, simply slip a sturdy rod through that end, tie the rod on to the rod on my fabric beam, wind the excess warp on to the fabric beam, thread the reed & heddles, tie to the warp beam and proceed as usual. In other words, there would be no knots (and less waste) on the fabric beam. I think I might have to make 2 crosses, one at either end of my warping board) to keep the warp in order, or is that necessary?

Is this feasible? What do you think? :^) 

Comments

claudia (not verified)

You would be better off leaving the end going on the back beam uncut and dressing the loom back to front.  There is a description of how to do it on the Interweave site here.  It's a pdf file and it has all the steps.  Or, Deb Chandler's book has a great description and pictures.

You have the right idea, just leave the back end uncut and make certain you beam the warp under consistent tension and you'll be fine,

Happy weaving,
Claudia

Sara von Tresckow

 As a new weaver, you'll be much more secure following Claudia's advice - when your warp is safely on the warp beam under tension, you have a lot of latitude with the cut ends during threading and sleying. When you tie on you simply pick up the bouts, even them out and tension evenly.

 

laurafry

There are several ways of getting a warp onto a beam and my preference is back to front as Claudia and Sara suggest.

I have some videos on my website and blog which you may find helpful.

http://laurafry.com

http://laurasloom.blogspot.com  On my blog scroll down the tags to the right until Video Clips

cheers,

Laura

callagain (not verified)

 Well thanks ladies! I will heed your recommendations and go back to front. Between the Handwoven files and Laura's videos, I'm sure I can figure this out. Now, I guess I'm making the raddle I previously didn't need :^)  

sally orgren

I do it this way for exactly the reason you state, it saves time and materials!

I literally slip the lease sticks into the cross while on the warp board, and then slide the warp bout right off the peg onto the rod. Or, I'll slip it onto my finger and then transport the warp bout over to the rod.

Also, I transfer the warp to the rod while the rod is separate from the loom. So if it is a very wide warp (I have done over 1,000 warps in the past at full width of 45") I can keep adding new bouts to the rod until the rod is full, then bring the rod and lease sticks over to the back of the loom, affix the rod via lashing to the apron and suspend the lease sticks (maintaining the cross) at the back of the loom so everything is ready for beaming. Sometimes I have pulled the lease sticks forward, in front of the castle. I like them positioned best when the warp is traveling in a straight line from the front to the back.

When you start to have these "ah-ha!" moments, you know you have *truly* become a weaver!

 

 

callagain (not verified)

Hi Laura,

Just letting you know, I could not get either of the  videos to play on your website. I waited quite a while to allow it to load, but still nothing. Maybe I didn't wait long enough? What do you think?

laurafry

Not sure - it may be a software problem.  The video clips on my blog should run okay though.  If you want, contact my webmaster (contact link on home page) and let him know there are problems.

 

Cheers,

Laura

francorios (not verified)

I just played the video on my PC. I had to download and install a new windows media plugin and restart my firefox browser.

You can try updating your media player.

Have a good day!

Franco Rios

Submitted by Anonymous (not verified) on