I notice there are now 500 members of this group.  I'm sure that many of you have some great ideas to share.

Personally I'm just recovering from a broken ankle.  The good news is that I've been able to weave as part of my therapy (who knew?).  The hardest part was getting the loom dressed, but because I already used a warping valet (trapeze) I've been able to manage dressing the small loom by myself.

If it hadn't been for having this tool already available I would have had to rely on others to beam my warps for me.

Since my studio is also set up in order for me to work as efficiently as possible given my space and budget, this was also of enormous help in getting me back on my feet.  Literally.

Anyone else got a story/tip to share?

Cheers,

Laura

Comments

francorios (not verified)

Hi Laura,
 
Here is my best trick for rigid heddle weavers.
 
When winding the warp on, the warp is attached to a book bag full of books with a dog leash.  The resistance of dragging the bag across the carpet puts enough tension to tightly  wrap the yarn on the beam.

In the past I've tied soup cans and other weights to the yarn, but this is better.

In the picture is the book bag in lower left, a pink dog leash (for Chloe the Chihuahua), then the warp yarns going up to the Cricket loom in the upper right of picture.
 
Can't take credit for it. The African weavers often use a little sled on the ground with rocks piled on to act as a deadweight tensioner.

Have a good day!
 
 

 

laurafry

Very clever.  :D  I'm all in favour of a warp beamed with tension.  

Cheers,

Laura

tien (not verified)

My handy tip: "snap" your skeins!

I just finished dyeing 800g of 30/2 silk.  Because this particular batch of yarn was slightly underplied, it tangled and twisted back on itself in little wigglies as it dried.  I tried unwinding one skein and it took me nearly three hours to do half the skein!

Then I remembered that "snapping" the skeins before winding them off helps untangle minor messes.  So I "snapped" the next skein and lo! I'm only forty-five minutes into winding it and I've already done half the 100g skein!  (I know that still sounds like a long time...but compared to what it was before, that was swift as lightning!)

To "snap" a skein, put your hands inside the skein, and jerk the skein open.  Rotate skein 1/4 turn, and repeat.  Do this all the way around the skein.  It will untangle loads of minor tangles and the skein will reel off much more easily.

And, while I"m at it, orient your swift so it rotates along a horizontal axis rather than a vertical one.  Makes winding-off easier!

Tien

laurafry

Absolutely correct!  :D  I noticed in the latest Treenway newsletter they also recommend orienting the wooden swifts with the axle horizontal.  I first learned of this in Ulla Cyrus-Zetterstrom's book - it's a life saver when working with fine threads.  :D

Wish I had your get up and go - mine seems to have got up and went.  :P~

Cheers,

Laura

Sara von Tresckow

OR, if you  happen to have an efficient squirrel cage swift, it can be a lifesaver.

While the squirrel cage looks as if it puts stress on the yarn, I have had wonderful luck unwinding some of Habu's more exotic fine silks by going slowly and carefully - the cages keep the yarn "on track" and there are no supports or arms to catch on.

I use the big one from Toika with support on both sides of the frame.

 

laurafry

I have a lovely squirrel cage swift built by a local craftsman.  It's my preferred method of winding off skeins.  :)  I love that it adjusts to handle very small to rather large skeins.

Cheers,

Laura

tien (not verified)

Sara, do you find that the squirrel-cage swift puts less stress on fine yarns than a regular swift?  I have a regular umbrella swift that I use most of the time (it's out on loan right now) and haven't had trouble with the yarns "catching" - but there is quite a bit of inertia that jerks the yarn when the swift starts up.  If a squirrel cage has less momentum then I may get one.

(Too bad Mike and I agreed that only "both of us" stuff goes into the wedding registry...or I'd put a squirrel cage swift on in a heartbeat!)

Tien

Sara von Tresckow

 
Get one cage for each of you...... (remind him he won't EVER need to hold skeins on his hands with outstretched arms)

Seriously, I find that the squirrel cage has a smoother action than a swift. I do sometimes need to "nurse" the feed at slow speeds, but using a spool or ball winder with it is a real joy.

With coarse yarn, it really gets up speed - and when you've got even fine ones running well, you don't need that much drag to keep things rolling.

Another plus is that I can mount multiple skeins (must all be the same diameter) when warping multicolored warps - take a few threads from one, break and tie to another and move on.

That said, I still have my first swift and use both on a regular basis.

Aunt Janet (not verified)

OK, I just dyed up some skeins of fine silk.  Dying went well. Snapping the skeins works wonders.  Now the problem.  From swift to ball winder, I wasn't paying any attention, just winding away.  Now I can't remove the ball from the winder.  I used a piece of cardboard onto the winder, thinking that would be enough.  Nope, it is on tight!  I'm winding back onto the swift, which isn't working very well.  the skein is now loose and I broke the thread and can't find the end.  Half of the ball is still on the winder and it still won't come off.  I'll take some more off today, but I'm not a happy camper.  I winding directly to pirns, but kept breaking the thread.

I doubt that there is a good solution to taking this off easily.

The tip is to not do as I have done.  Wind a smaller amount onto the ball winder, checking now and then to see if it will slide off.  Don't wind on that tightly either. 

Actually not sure how I would wind with less tension.  Anybody?

Janet

wilowind (not verified)

 

 

I also use a claw hammer (on carpet) or a rice bag to drag along for tension. I've also seen a method whereby you stand at teh back of the loom, grab the warp & twist it to provide tension while you wind it. I don't know how well the later works with long warp, Hope that helps.

Cathy S/Willowwind

tien (not verified)

I put an index card over the ball winder "core" and tape it tightly together.  Friction keeps it from coming off while you're winding (you do have to wrap it TIGHTLY), but afterwards you can just grab the end and slide it right off, index card and all.  Bonus: you get a cardboard "core" to the ball so it doesn't collapse in on itself and tangle.

I know some other people use toilet paper cores for the same purpose, but I've found them  to be too loose, and never seem to have one lying  around when I want one.

That said, I use a conewinder most of the time, these days...have a Silver Needles electric conewinder (pricey and slow) and a double-ended bobbin winder with a conewinding adapter that Sandra Rude's husband Mike made for me.

Tien

francorios (not verified)

I've seen the grab and twist method for putting tension on rigid heddle  also.

That takes a little more coordination than I can muster.

The concept of "tying it to a rock" is exactly where my head is at.

Thanks for the reply.

Have a good day!

laurafry

Just wondering what kind of swift you have and how it is mounted?

A wooden umbrella swift works much better if it is mounted with the axis horizontal.  Unfortunately that doesn't help with the current skein, but perhaps will be the solution for future skeins.

My preference is to use a squirrel cage swift.

Cheers,

Laura

Aunt Janet (not verified)

I have a wooden swift, mounted with the axis horizontally.  I just put too much pressure on the ball winder.  A lesson still in the learning.  I will look into a squirrel cage swift in the future.

Thanks for the reply.

Janet

SusanP (not verified)

Actually, I am looking for tips rather than offering one right now.  I just bought my first end feed shuttle.  I opted for the Bluster Bay mini because the project I need it most for is working with 20/2 spun rayon for scarves.  I was having trouble with the floating selvages breaking and I figured that if I could eliminate the draw in the problem would be solved.  Well, I just love the shuttle, but I am having trouble mastering the knack of winding the pirns.  This shuttle uses cardboard pirns and the flair at the wide end is minimal.  I was hoping to find a video of someone winding pirns so they feed smoothly.  Does anyone have any suggestions? 

tien (not verified)

Have you looked at the Bluster Bay website for their instructions?  http://www.blusterbaywoodworks.com/instructions.html

When working with their cardboard pirns, I make the back end bigger by winding just a little bit more yarn on the back part when winding back and forth.  You have to be careful not to get too greedy - if you make the back end too big too fast, the yarn tends to slide off resulting in an unholy mess!  (Ask me how I know...)  Practice with some junk yarn in a waste header first, is my suggestion.

If you find that you would prefer to use a larger Bluster Bay shuttle with more conventional pirns, I have a full-size Bluster Bay EFS that I would LOVE to trade for a Bluster Bay mini - so send me a message if you are interested in a swap.  (I have a small shed and find that the minis work better than the full-size ones in the same shed.)

Hope that helps!  I don't know of a video, but maybe the instructions will be helpful?

Tien

SusanP (not verified)

Hi Tien,

Thanks for your suggestions.  Yes, I have read the Bluster Bay instructions...many times.  I thought if I could watch someone wind the pirn it would help.  The first pirn I wound worked fine (before I read their instructions) and then the second one isn't feeding smoothly at all....and I thought I was following the instructions on that one.  I know I just have to practice and I am using the end of a warp as practice space.  I still have about a yard of weavable warp on there to play with.  What I really need the practice with is winding the pirn.  I may have to go back to winding it the way I did the first one even if it isn't the "correct" way to wind them.  I can't complain, this is only the second pirn I have wound.

Sorry.... but I don't want to swap shuttles.  I bought  this one for the smaller profile and lighter weight since I am doing scarves with fine threads and it is just perfect for that.  Thanks for the offer though!

BTW - did your wedding dress get accepted for the Convergence Fashion Show? (I can't imagine that it wouldn't get accepted...it's so beautiful!)  I can't wait to see it in the flesh!

Susan

SusanP (not verified)

Hi Janet,

I did the same thing so I know your frustration.  What I ended up doing is taking the the center post of the ball winder out and using the ball to wind bobbins with the center post still in it.  After I got it about 1/2 wound off I was able to remove the rest of the ball from the center post.  I had thought I would try wrapping cardboard around the center post next time, but it sounds like you did that and it didn't work either.  What I do now is wind onto cones using my double ended electric bobbin winder.  Someone on Weave Tech described doing that a few months back and it works like a charm.  You need the pointy ended cardboard cones and a jar lid that fits into the base.  I used a nail to puncture a small hole in the center of the jar lid to hold the point of the bobbin winder. 

I'd love to hear if you come up with an even better solution.  Good luck!

Susan

tien (not verified)

A quick search on YouTube finds this video: http://www.youtube.com/watch?v=xjGh0jtIIFw

It may not help you in figuring out how to handle the thinner end of a Bluster Bay mini, though, as it depicts a more conventional pirn. 

For winding on a Bluster Bay mini pirn, the important thing to keep in mind is that the yarn should NEVER drag over a bump in the pirn - that's a sure recipe for tangling.  So instead I start gradually building a small cone that is wider on the back than on the front.  I start with a flat layer, winding back and forth for about a quarter to a half inch.  I slowly build up the back end by continuing to wind as in a "normal" pirn (back and forth in a cone shape), but I gradually make the back end of the cone wider by spending a little more time winding onto the cone end each time I return for another pass.  This results in a slow buildup of yarn in the back.  The key is not to make too steep an angle at the back end of the pirn, or it will tend to fall off.

Practice winding with a worsted weight yarn, under tight tension - the pirns are small enough that it won't take that much of a worsted weight yarn to fill one, and then you can wind it off and use it for another practice round.

I found also that once I mastered the art with a regular pirn, it was a lot easier to figure out the Bluster Bay mini cardboard pirns.  So if you're really stuck, try it with a more conventionally sloped pirn and see if that helps.

And yes, the dress was accepted into the Convergence Fashion Show, so it will be at Convergence.  See you there!

Tien

SusanP (not verified)

Tien,

Thank you for the really helpful suggestions.  I think you're right about practicing with a heavier yarn at first...I will give it a try.

Congratulations on getting into the fashion show.  I would have found it very hard to believe if your dress hadn't made it it.  I really can't wait to see the real thing.  The photos on your blog are beautiful!

Susan

warpology

 I recently bought a English shuttle that uses wooden pirns. Unfortunately  the first one I tried to wind on my electric winder cracked. How do you wind these? I was taught not to use a hand crank for pirns but I'm thinking that that may be my only way. Any other idea's? ( shuttle in NC I'm in MI or I would post the name of the shuttle :) 

Lois

laurafry

I use my electric winder to wind pirns all the time.  The original ones were wooden and none of them ever cracked.  

Now AVL supplies plastic ones and none of them have been a problem other than the size of the hole in the shaft.  The larger ones require that I wind a little tape around the shaft of the winder so that they fit on.

cheers,

Laura

52ZOZARK WEAVERS (not verified)

JUST JOINED, LIKE TO SPEND SOME TIME ' ketch'n-up ' ON ALL YOUR SUGGESTIONS!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 

laurafry

Welcome - I'm assuming you live in the Ozarks?

Cheers,

Laura

Judith (not verified)

I just saw this post and want to say it's a brilliant idea.  So simple!!  I once had a really bad experience with a gallon jug weight and never tried weighting the warp again.  This looks fool proof.  Thank you for posting it.

Cheers

Judith

francorios (not verified)



And here's my other Cricket loom trick. The threads on the Cricket warp beam can cross each other, causing the shed not to open fully when weaving. So using chop sticks to make a new cross on this side of the heddle, I can straighten the warps so there is no problem on the weaving side of heddle. I just push the sticks back and over the big dowel when I advance the warp. Much faster than using a crochet hook to chase all those threads.

Have a good day!
Franco Rios

Caroline (not verified)

Nice one Franco! I just LOVE chopsticks, they are almost as useful as shoe laces!

Submitted by laurafry on