I really need to get all my questions together before I finish off.  Does any one know where I could find or get a TOTT manual? I am beginning to think that is what I need. :)

Kathy

Comments

claudia (not verified)

Kathy,

I have a single piece of paper that came with my loom.  I will PM you and see what we can work out.

Claudia

kteaden (not verified)

Thank you Claudia. I did contact Weavers Friend per Michael White's suggestion. I would be happy to work out what ever information I can on this loom. I really want to get it to work and get to work on it.

claudia (not verified)

I have scanned the copy I have of the loom instructions from ARt.  Please PM me your email and I will be happy to send you a copy.

Claudia

claudia (not verified)

I emailed you the instructions from the TOTT yesterday.  Did you get it?  I noticed the pages were upside down.  I can copy it and snail mail it if you email back your address.

Claudia

kteaden (not verified)

I sure did get it . No problem, I just turned the page around.  :) Thank you so much. I am also getting a manual from Weavers Friends. Between the 2 I should have it all figured out.

Kathy

claudia (not verified)

I am very curious if the manual from Weavers Friend is more detailed.  Please let us know when it arrives.  I found the instruction sheet I was given to be of little help when tying up the treadles, which is what I was looking for.  Both Sally and Daryl have their own methods for getting the treadles/shafts even.  It always caused difficulty for me. 

Thanks,
Claudia

sally orgren

Claudia,

Can you send me a copy too? I don't think I have any documentation with my loom, Marge just sent hand-drawn or written notes, and labeled everthing meticulously, so it was a pretty easy reassembly.

(And I didn't even think to check Janet Meany's site, so that was a great suggestion!)


Sally

kteaden (not verified)

Hi Claudia,

I have not received the manual from Weavers Friend yet. When I do I will let all of you know. I hate to tell you this but the copy I got from you was too small to read. I tried saving it every which way and enlarging it and it just got blurry. Is there anyway you can send it again? But, bigger. The treadles are all mixed up and that is what I wanted the manual for. I'll get it figured out but it may take me awhile. It looks as though some of you are coming to Albuquerque for Convergence?! Hopefully I will have it warped by then! It would be nice to meet you and Daryl. Let me know if you can resend it.

Kathy

Michael White

Kathy, maybe you can get Sally to send you pictures of the treadling, she takes great pictures.

Michael

claudia (not verified)

Hi Kathy,

Sally already told me so I am working on making my scanner do it larger.  I'm sorry it's too small, my lack of computer knowledge has slipped out again.  Ooops.

Claudia

kteaden (not verified)

Yours, Claudia? My computer knowledge is horrible. Don't feel bad. I'm glad I still have a 20 year old at home to help me out! Thank you. I will look for it shortly.

Sally, would you mind sending me a picture of your treadling and of your right front brake? The brake arm is just hanging down and I think it should be connected to something to lock it. I will attach a picture. This loom has been out in a garage for some time and the person we got it from knew very little about it. I'm learning though with all of your help! The treadling is missing several chains. I think.

Michael White

Claudia, what I do is take a photo of the page. Then send it in a high res. so that is can be enlarged, sample below. 

claudia (not verified)

See the metal piece on the wood arm?  Turn it so the point is facing up so it engages with the brake.  The metal piece on the top of the brake holds it in place. The wood arm is only used to advance the warp forward onto the cloth beam as you weave.  It won't work properly until you turn the metal piece to face upward then when you need to advance the warp you lift the wood arm and engage the metal piece onto the ratchet and it will, with the pawl in place maintain the tension on the warp as you move it forward.

When you want/need to advance the warp onto the cloth beam you step on the floor pedal below the front brake to release some of the warp from the back beam.  Then, lift the wood arm and sort of push in so the metal piece engages on the ratchet and push down, moving the ratchet clockwise to advance the warp.

This is probably all as clear as mud but give it a try and I think you will see what I mean.

Claudia

sally orgren

Good suggestion about the photo, Michael. Most people can easily take a photo and load it, but messing with scanner settings can be a little more frustrating and you can accidentially get huge files sizes without meaning to do that!

----

Kathy—I am traveling for another day yet, and I don't think I have any photos in my laptop that show what you are looking for, so give me a day to get back to NJ and I'll upload some more photos (unless Daryl beats me to it!)

The chains you can get at Home Depot or Lowes. Bring one in and match it up to what they have. Again, I have added more chains, and I can take a photo of the replacements when I am back home. (I think the new ones are rubber coated.) You just have to add a washer at the top.

Daryl uses Texsolv with a special knot at the top, and I like that suggestion for possibly replacing the chains. I hope she posts detail shots of that. It was on my agenda to check them out the next time I am over at her studio.

I would choose one or the other, but not a comination of both. The chains might add more weight, and unless evenly distributed across the width and number of lamms, I am not sure how well that would work when treadling.

Sally

sally orgren

Underside of my brake. In comparison, it appears you are missing this little screw to hold the lever in place...

(Apologies in advance about the dust—I am working on a very linty warp at the moment!)

sally orgren

Just anticipating another possible question, here is my brake tie-up in the back with the two beams. (I am leaving within 24 hours for another work trip, so I won't have access to the loom again until next Thursday, when I return.)

It looks like you may have two back beams also, judging by the low position of one of the beams in one of your previous photos. (My second beam that is mounted in the lower position is my sectional.)

If you need a different angle, let me know.

 

sally orgren

Propping the treadles for shorties on the TOTT.

Here is what we were talking about. Note the piece of 2 X 4" under the front of the treadles. It raises them up a bit, changing the angle of the treadle to the lamms, especially the shafts that are toward the back of the loom.

I am 5-5" and this is a 10-shaft pattern. I actually prop my butt on the bench with a low cushion (a quilt folded over a few times) to get a bit more height and "oomph" on the treadles. (Yes, I STOMP those threadles! ; - )

As you can see, I am using a lot of treadles. I decided to weave the pattern "upside down" so I have to do less lifting. "Upside down" means lifting the opposite shafts as indicated by the draft. If you decide to do this, be sure to check your pattern with a mirror frequently and triple-check your tie-up. (I usually weave a sample first.)

For the pattern pick that I have to lift the most shafts (7 shafts out of the 10) I actually broke that up over two treadles, because I noticed one treadle was already lifting 4 of the shafts needed for pattern pick #8. The further left or right from center you get, the harder it will be to treadle if there are a lot of shafts being lifted. (So if you have to tie up a lot of shafts to one or two treadles, try to keep them near the center.)

And you will notice I leave some treadles unattached. That helps me "feel" with my feet the pattern area and the tabby areas, which I put on the outside to keep me balanced-up when weaving. When beginning a pattern, I sometimes number the treadles with tape, but that isn't necessary if it isn't a complicated treadling.

Hope to see your first warp on your TOTT soon!

 

kteaden (not verified)

Thank you Sally! That helps a lot! You know what they say, "a picture is worth a million words"! Although, I do understand what you are saying too, Claudia. Yes, my loom does have 2 back beams. I noticed too that on all your TOTT beams you still have the cloth on the beams. Anyone changed those over to Texsolv? Because this loom was in a garage for several years the cloth is very dirty. You all have been so helpful. If I didn't have Weavolution to ask, I would be VERY lost right now.

Kathy

Marsha A. Knox (not verified)

What is a TOTT Please?

sally orgren

"TOTT" is shorthand for the brand name of this loom, which is "Tools of the Trade"

-----

My cloth beam had some light stains when I got the loom, but it works just fine.

I DO prefer the canvas apron, as it helps smooth out the knot areas a bit when beaming, but doesn't take up that much space.

I have rebar on both ends of the loom, so the cloth apron attached to the back beam is also attached to rebar #1. I slide the warp onto rebar #2 and lash that to rebar #1. With this method, I typically get beween 18-22" loom waste on the back.

Keep in mind, this is a 12-shaft loom, so the castle is fairly wide to hold all those shafts. If my rebar had been cut just a *bit* shorter, and could enter the castle, I probably could have decreased the back-end loom waste a bit more when weaving on less than 12.

My rebar has been tightly wound with some kind of tape, so it doesn't leave marks/dirt/rust on anything.

Michael White

Sally, rebar is made of a soft steel and can be cut easy with a hack saw.

Michael

debmcclintock

 maybe there should be a "Tools of the Trade" group?

sally orgren

Just  checking in to see how Kathy is doing with retooling her TOTT loom?

kteaden (not verified)

Hi Sally,

I have been using a rental loom while taking a class. I have been cleaning it and this week end I am going to work on pulling the cloth off and seeing if I can wash it and reattach. Hope it works. I am a teacher and school here in Albuquerque is out in 11 1/2 days. That loom will be warped soon after. I can't wait. By the way I got the TOTT manual. It is quite interesting. I know a couple of people wanted it. My email is [email protected]   I guess it is okay with me scanning or copying it. If anyone thinks I can't do that please let me know.

Thank you for all your help and I will let you know when it is warped. Weavers are the nicest, most helpful folks!!!!

Kathy

sally orgren

Gosh, Kathy!

As it sounds like you are located in Albuquerque, are you planning to attend Convergence this summer? (July 21-25)

If you haven't signed up for the whole conference, you can attend just for the day for a fee of $10 I think. That will get you into the vendor hall and exhibits (including the fashion show exhibit which usually has about 80 garments displayed).

Weavolution will be in booth #329 and I am initiating a meet-up between 5-6 Thursday outside the vendor hall, in the convention center. Usually that area is open to the public and that is the only time there aren't other conference activities scheduled. So if you come by, we can meet face-to-face! Also, on Thursday the vendor hall reopens at 8:45 p.m. for "midnight madness"  deals, so that is certainly a way to get the most out of your $10 admission with additional access to the vendor hall.

Sally

p.s. disclosure—I am just planning to attend the conference and have been going since '98. I not an organizer or rep for HGA or anything like that. 

kteaden (not verified)

Hi Sally,

I most certainly am planning on attending. I cannot wait to meet many of you. I keep seeing many of the names pop up that I have "talked" to. Thank you for the info and I will be there Thursday then for sure. If you, Daryl or any one else want any of this information that I got on TOTT send me an email and we will work something out. Not much but it's interesting. There is a short newspaper article on Arthur Weitzenfeld. The manual part was pretty much what Claudia sent me. The info I got did include a price list. Interesting read. [email protected]

Kathy

sally orgren

Here's a SHOUT OUT to Daryl! (We'll see if she's sleeping now that she has a brief hiatus from traveling and teaching.)

Please take a photo of your Texsolv conversion and post here. On my "Potpourri Super-Sticky Rayon" warp, I busted a chain on shaft one about every 12". So I am seriously considering the conversion, but I want to see how you affixed the cords to the lamms. (You DID or DID NOT use a lark's head?)

Also, do you have the cords attached at all possible positions, and just leave them hanging down when not in use, or do you only lace up the ones you need up when you need them? (My preference is to get enough to make them for all the possible combinations, and just let them hang loose like I have seen on Baby Wolves.) Do you foresee any problems with that?

Finally, where can I get huge reels (yards and yards) of Texsolv cord to do this economically?

Okay, I await your response as I tie a new warp onto the sticky-stuff, and expect a much happier weaving experience in the near future—

 

 

Marpeg (not verified)

I purchased a TOTT this spring and have been reading in the posts about a manual. I would love to get a copy of this. My email address is [email protected]. Thank you and have a wonderful Thanksgiving. Peggy

sally orgren

Marpeg, The manual is typewritten, and doesn't cover much. I am traveling this week, but will try and remember to make you a copy or scan when I return Monday.
Submitted by Anonymous (not verified) on