I'm a newbie weaver, and I've clearly bitten off more than I can chew. But now that I've taken the bite, let me see if I can salvage this project...

I'm trying to wind a warp (400+ ends) of 2/30 Colourmart silk, and it's giving me fits. It's tangling between the heddles and I've already broken a thread or two in just a few inches of winding on. What's the secret? It sticks together and forms these little fuzzy adhesions. Most of the warp is loose, but then there are these clumps. Even if, by some miracle, I got the whole thing wound, the tension would be impossibly bad. At this point, I'm ready to just cut it off and start with something I think I can handle -- like wool...

Any help/suggestions will be greatly appreciated.

Nora

 

Comments

debmcclintock

 Madame...Put the scissors down and walk away from the loom.  

When you come back....Divide it up into one to two inch sections and chain it off the loom and store the chains.  Revisit it after a couple more warps on your loom and put it on back to front slowly.  You should be able to salvage it with care in the chaining off and back on the loom.  Get some more mileage on the loom before you try it again!  Deb

noramcd (not verified)

Certainly I can do that, and most likely will.

But I will still need to know why it is tangling the way it is, and how to deal with the tangles when I approach it again... I think that more miles will not necessarily solve this particular problem. Even if I started over from scratch, I would want to know what I did wrong this time so that I do not repeat the same mistakes.

I see a hint in your answer; I wound it all in one chain. Is it normally the practice to wind this type of fiber in smaller chunks?

tien (not verified)

Are you winding from back to front or front to back?  Back to front puts less stress on the yarns and works really well in my experience.  I've worked with Colourmart's 2/28 nm silk yarn pretty often and not had problems, but I haven't tried front to back warping.

With sticky little adhesions, sometimes sizing the warp can help, but based on my experience with Colourmart yarns, that is probably not the issue here...something is causing the fibers to abrade against each other in the warping process.  I'm guessing that you are warping F2B and that this is causing at least some of the problems.  For fine fibers, B2F generally works better.

Tien

Joanne Hall

Nora,

If you decide to take it off the loom, be sure to put a cross into each of the bouts before you take it out of the heddles.  And when you cut it, try to keep all the ends the same length.  Were you careful with that when you tied it?  Yes, you probably should have wound this warp in about four bouts.

Joanne

lkautio (not verified)

It isn't necessarily the size of the warp chain, it is how you handle it.  When I warp fine silk, I use back to front (wind on the back beam then thread), with two crosses - a simple raddle cross on one end (the end that starts winding onto the back beam), and a threading cross on the front.  The raddle cross, unlike the 1x1 (or in my case 2x2 or 3x3) threading cross contains however many threads are in each 1/2 (or 1/4" or 1/8") raddle bundle so it goes on very quickly and easily.  You keep the warp wrapped under good tension on a kite stick (a stick shuttle will do).  A thread under tension will not tangle easily. The problem you may run into with this method as a newbie is that your warp may not be wound initially under even tension or you may introduce tension problems when you take it off and try again. 

You might be able to salvage what you are doing by slowly beaming on with an open shed (it separates the threads), and perhaps some gelatin sizing.  A sett that is too close won't help.  That said, 30/2 spun silk is usually strong, and should not require much special handling.  Occasionally you run into a batch that is poorly made.  I have not tried the Colourmart silk so can't comment on it in particular.

It's amazing how much easier warping gets after you put on a few more.  I swore off linen as a beginning weaver (its lack of elasticity demands excellent technique) but it is one of my absolute favorites now.

Good luck!

Laurie Autio

noramcd (not verified)

Thanks everyone for all your helpful suggestions -- there is much to digest here.

As you all have guessed, I am warping front to back. I have not yet warped back to front, but it sounds like that would have been the way to go. I will have to look up how to warp back to front. If someone has a good link, that would be a great help.

I did tie all the ends evenly. And I'm sure it's not the silk, it's the weaver :-b

How do I recreate a cross if I take it off the loom? I thought the cross was just to get the correct threading order, and that it was not necessary to preserve it.

The other thing that may be causing problems is that there are multiple ends/dent, and I took them randomly when threading the heddles. I'm quite sure there is no crossing between the reed and the heddles, or between the heddles, but the ends may be slightly out of order within the groupings/heddle. I did not realize that disorder by one or two places would cause drastic problems.

Ugh... I'm pretty sure I'm not going to be able to wind this warp on and maintain what is laughingly known as my sanity. It's too bad; it's a very pretty color and it coordinates perfectly with the cashmere I was going to use as weft.

Laurie, you said:

"When I warp fine silk, I use back to front (wind on the back beam then thread), with two crosses - a simple raddle cross on one end (the end that starts winding onto the back beam), and a threading cross on the front.  The raddle cross, unlike the 1x1 (or in my case 2x2 or 3x3) threading cross contains however many threads are in each 1/2 (or 1/4" or 1/8") raddle bundle so it goes on very quickly and easily.  You keep the warp wrapped under good tension on a kite stick (a stick shuttle will do).  A thread under tension will not tangle easily. The problem you may run into with this method as a newbie is that your warp may not be wound initially under even tension or you may introduce tension problems when you take it off and try again. "

Do you have a picture of this in progress? I'm having a hard time visualizing, due to the newbie-ness. Also, your answer implies that it's OK to wind your warp with 2 ends held together. Have I interpreted this correctly?

Nora

Edited to add: I found on-line back to front warping instructions/pictures, and will study them carefully. It may not help me with this warp, but it will probably save me some grief in the future.

Sara von Tresckow

 You might wish to purchase a copy of Laila Lundell's "Big Book of Weaving". This is a most comprehensive book about weaving and weaving techniques including excellent warping instructions, drafting, problem solving and some nice project ideas.

The cross should be preserved throughout the weaving process for many reasons. Any source that doesn't respect this is to be considered second rate.

debmcclintock

 Hi Nora, I checked your profile and I don't see where you are located.  We can get you to some teachers or some guilds to help you over the learning curve if you could update your profile.  There are guild libraries and videos that might help you. Check the groups here in Weavo for state information if you are located in the US.  From your questions it sounds like you are learning on your own from the internet and books.  It helps to take a class or get some private instruction on your loom that gets you to the next level.  

Just a hint, there are many different ways to do the same thing.  My comment about milege is to learn why you are doing something and understand the goal...such as back to front warping in chains minimizes abrasion on warp.  That just takes putting different warps on and working thru them.  Once you do some troubleshooting and understand the different approaches you can make a choice on how/why you choose something.  Belonging to a guild, study group or taking lessons helps you with that.

Enjoy the journey, Deb

laurafry

Tangling can be minimized during beaming by adding weight to the warp chain.  Loose threads tend to wrap around each other and if there is a tendency to pill (the little fuzzy bits) a loose thread will do so more readily than one that is under tension.  A thread under tension is a thread under control.

Personally I found that front to back warping just didn't work very well with finer threads (finer than about a 10/2 cotton), longer warps (longer than 5 yards) or wider warps (more than about 15 inches).

Back to front works in pretty much every situation for me - and I've done a lot of different things. 

I have some educational stuff on my website and blog including some video clips.

http://laurafry.com

http://laurasloom.blogspot.com

Cheers,

Laura

noramcd (not verified)

Thanks again to everyone for all of your helpful suggestions.

I do actually belong to a guild, but you know... your guild members aren't standing over your shoulder telling you that you're being a bonehead when you try to warp four and half yards of fine silk from front to back:-) Sometimes you just don't realize what you don't know until it's biting you in the posterior.

It seems that many of the folks in my guild are self-taught, but a workshop in the basics would probably be helpful:-)

Cheers, and thanks again for all the help. I will write down/find the books and cruise the web suggestions -- and think more seriously about a class in the basics:-)

Nora

Michael White

Nora, going back to the very basic operation of warping. You did not state or have been ask if you put any paper, sticks Etc between the warp layers as you were winding on your warp?

Michael

 

lkautio (not verified)

Nora, I'm sorry I don't have pictures.  Some books talk about a pouree and portee cross (spelling?), or a reed and a raddle cross.  I think it would be in Alan Fannin's book or one of Peggy Ostercamp's as well as any number of others.  Sigrid Piroch's book has lots of photos.  Any of these should be in your guild library.  I learned some of this from Lillian Whipple, the fine thread guru.

Yes, it is fine to warp with two (or more) ends as long as you keep them separated so that they don't twist as you wind them on.  I keep a finger between them and am careful that they have the same tension on both and go onto the reel (or board) together rather than spread apart.  It's a good way to cut your time winding.

To recreate the cross:  Open a plain weave shed under tension.  Slip a lease stick into the shed where you want the cross to be.  Open the other plain weave shed under tension and slip in a second lease stick.  Tie the two lease sticks together.  In your case you probably want to make this cross in front of the reed.  If you had it all beamed on and wanted to remove for later use, you would put the cross behind the heddles.

As others said, there are many ways to do the same thing.  While people swear by one or another, it is often equipment, yarn, and to some degree weaver dependent as to which works best.

Laurie Autio

noramcd (not verified)

Yes, I was using paper between the layers, but I did not get far enough with the beaming to use much of the paper.

Thanks Laurie. That should have been obvious to me... And thanks for the winding tips.

And now I'm off to play with some non-slippery, and somewhat thicker yarn. I have some handspun that has been telling me that it needs to be a scarf. The last handspun scarf I wove turned out well, so I think I can safely carry that off while I'm reading the links and books all of you have kindly listed for me :-) One must take one's successes where one can...

Joanne Hall

Since this is a familiar project for you, it might be a good time to try back to front warping.  It would not be good to try it the first

time on a more difficult warp.

Joanne

fiberfan (not verified)

I 2nd Laura's recommendation to beam under tension, I am pretty sure I learned of beaming under tension from Laura's posts to 2 weaving email lists.  I beamed a sticky alpaca knitting yarn scarf warp a couple of weeks ago and had no tension issues weaving the scarves.  With the narrow scarf warp it was easy to apply tension with one hand while turning the beam with the other.hand.

noramcd (not verified)

OK, back to front, and under tension it will be for my next handspun scarf. Trying new techniques on a familiar project is a good suggestion.

I ended up spinning the afternoon away on another batch of fiber, so the yarn I spoke of earlier, and the loom, still wait...

 

Submitted by Anonymous (not verified) on