A Clipboard Loom   I designed a loom based on a clipboard for doing narrow bands.   Article has been posted in Weaving forum http://www.weavolution.com/node/7610   Have a good day! Franco Rios  

Comments

mischiefmanaged (not verified)

I've been looking around for an old strong small picture frame or something like that to try this out (not having an extra clipboard laying around . . . although who knows what I'd find if I cleaned out the laundry room . . . ). Looking around my craft room, I found a PVC lap quilting frame that I got when I tried out rug hooking. I think it is about 11x11 inches and I plan to try it out next week!

francorios (not verified)

That lap quilting frame should work.

Let us know how it goes!

Have a good day!

Franco Rios

mischiefmanaged (not verified)

Here it is, not a clipboard, but another simple portable loom. It's a PVC pipe lap quilting frame but I guess you could get PVC pip and corner pieces at the hardware or home improvement store and make your own. I warped mine according to the directions for a Hopi belt loom in Mary Pendleton's book Navajo and Hopi Weaving Techniques.

\

 

The left edge of my warp is messed up, but it's fun to venture into two colors!

francorios (not verified)

That looks good. I could certainly make them with part from the hardware store.

That's a good start on your band.

Keep it up. It gets better.

Have a good day!

bolivian warmi

Can you buy those half pipe bits at the hardware store too or do they only come in the quilting frame kit? I guess it would make a good embroidery frame too. I love your little shuttle-did that come with an inkle loom? Is it beveled so you can beat with it too?

mischiefmanaged (not verified)

Hi Laverne -- don't know about the corner  or other pieces; Franco, do you?

The shuttle I bought new on ebay; it is meant for an inkle loom and is beveled. It works well as a beater on narrow warps. The make is Finniwig Studios.

Cindy

francorios (not verified)

The long pieces with the cut out strip can be made using a utility knife, sometimes called box cutters.

Use new PVC pipe because old PVC gets brittle and hard to cut. Avoid electric saws because the saw may catch the plastic and cause it to shatter.

Buy a pipe a little larger than the other. The larger would fit over the smaller.

Have a good day!

Franco Rios

rose Goldielocks (not verified)

It is frustrating! to cut the PVC to make the "clip" portion of the PVC quilting frame. When I tried, I found it almost impossible to get a 'straight' lengthwise cut. (mostly because of the structure of the plastic grains inside the pvc pipe).

Cutting a straight horizontal line is not a problem. A box cutters (utility knife) works pretty good for 3 or 4 cuts on the pvc. The easiest way is to mark the place to cut all the way around with pencil/pen/perminant marker and then ROLL the pipe on a flat surface while applying pressure with the knife.  If you have acess to a 'miter box' or a 'hack saw', that is the best choise.

Sharon

francorios (not verified)

I sorry my advice did not work out for you.

I've cut PVC lengthwise with a box cutter before.

I checked the web for other ideas and this page

http://www.pvcworkshop.com/freePVCplans.htm

recommends using a handsaw or or dremel tool.

You mentioned a miter box and I believe the handsaws that are used with miter boxes have fine teeth which should work on PVC.

Have a good day!

Franco Rios

mischiefmanaged (not verified)

I only used the clip portion to secure  a few warps that were loose. I warped directly onto the frame. My hope is that with more experience I will not need to use the clip portion. If you were securing a piece of fabric for embroidery or something, then the clip portions would be essential but I'm not sure for weaving . . .

woventhreads (not verified)

I am using something like this to weave moebius strips as a single piece (as in not sewn together).  I found, however, that the pvc was quite slippery and my warp drew in.  I think I've solved this with, of all things, hair curlers -- I'll know shortly.  I'll post pictures, etc., soon (I'm at work right now).

Submitted by Anonymous (not verified) on