I am considering buying a second hand varpapuu loom. Does anyone here have experience with this make? It is an 8 shaft 130cm countermarch loom.

I was thinking my next loom would have to be a (smaller) glimakra, but in the picture I have seen of it, it looks very much like one, and the seller lives a fair distance away, so I can't just come by and have a look.

Any info would be appreciated.

Comments

Sara von Tresckow

 I nearly bought a Karelia (the one with the hanging beater) back in the 1980's. Good brand - I decided on a Lillqvist - another Finnish loom that was nearly identical save for using wedges vs. bolts to secure the loom pieces. I know some Varpa owners as well - the looms are VERY similar to your Glimakra, except they are made of birch so a little heavier.

Excellent loom choice. If this is the model I think it is, they are a bit shorter than the standard Glimakra looms, but built with the same size timbers and full sized in the area where the weaver works.

Joanne Hall

Since you are used to a hanging beater, the lower beater would be a big change for you. 

Joanne

Sara von Tresckow

 Not all Varpa looms have an underslung beater - only the Ffnlandia does.

Back in the 1970's and 1980's there were a number of European loom makers who either didn't export or exported only a few looms to N. America. Today there is much skepticism when  such looms come up on the used market. Since the traditional CB or CM loom is essentially sticks and string, there is absolutely no need to bemoan a "lack of factory original spare parts".

For those on Weavolution living in Europe, I'm putting up a list of some of them These were not large factories, but more like the original Glimakra or today's Oxaback, they are woodcrafters, cabinet makers who also make looms from plans that they own. Mostly they make/made traditional counterbalance or countermarche looms - I don't know of any brands to avoid. However, at times there were "special" models that folded, had exchangeable cassettes, imitated jack looms, etc. Those have not aged as well.

A well made traditional CB or CM loom should last around a century, meaning that these older used looms would make an attractive addition to a weaving studio:

Glimakra-Sweden

Oxaback-Sweden

Toika-Finland

Varpa-Finland

Lilqvist-Finland

Berga-Sweden

Lervad-Denmark

Dryad-Great Britain

Arm-Switzerland

are but a few Some models have overhead beaters, some underslung -  one needs a photo to confirm that. Some were vertical rug/tapestry looms of a type seldom made any more - and quite interesting because they take up little floor space.

Since the design of these looms is so similar, they are practically "interchangeable" in terms of desirability. 

Also, there were some legendary loom builders who made some equipment for "home" use as well as professional looms Marquardsen in Flensburg(Germany/Denmark) was one of these. In England there was Harris and Maxwell. Some of these looms are so big you need to "climb the rigging" to dress, but they make a wonderful weaving tool. There were also rug loom makers in Bavaria and Austria who left behind wonderfully reinforced large looms.

I start drooling when I look through something like the used loom list in the UK or the ad Pages of Weben+ - there are some very good offers out there. There should be no real reason not to consider these looms - it is no wonder that some of the makers are gone - the looms outlast the demand. However, I am certain that those plans are somewhere ready to produce more on an as needed basis.

Ellen (not verified)

Thank you for your information. The loom I am looking at does have a hanging beater, so that is no problem. I am still considering. It is just that the glimakra looms I know all have this marvellous finish and quality.

Ellen

nordicweevs (not verified)

I did own a Varp. 16 treadle 12 harness and sold it.  I did not like the fact I had to crawl over the side braces to tie up the harnesses to the treadle for a specific pattern or that it did not have a hanging beater.  My Glimakra fits my needs perfectly, 8 treadles, 6 harness with side opening to access for tie up.  Es in ME

Sara von Tresckow

You are describing the Varpa FINLANDIA, not the loom that Ellen is looking at When in their prime, they made your model, one or two with hanging beater - including the Karelia which is an excellent all purpose loom, and the Lapponia - an upright loom with beater suitable for large rya rugs and tapestries.

Varpa Looms is the manufacturer, not the model. Please do not judge a manufacturer by the limited range of imported looms available in the US.

nordicweevs (not verified)

I'm sorry I commented on the loom I owned and thank you for the clarification

SallyE (not verified)

I know this is an old thread, but here goes. . . . I have a chance to get Varapuu with a lower beater.  Is that going to be a problem?   Also, looking at how the hanging beaters work, I don't see why that couldn't be changed with a little carpentry.  

 

Dawn McCarthy

Ellen, I had a Varpa loom which is the same as the Toika Liisa.  It had an underslung beater (which doesn't bother me despite my other two looms having overhead). GREAT for rugs, I would do put the cords for the treadles through the lamms  prior to attaching the warp to the front apron, that way it was easy to remove the knee beam and breast beam for easy access. 

I liked it so much that when a Liisa came available I got it!  I have pics on my blog of how I adapted the treadle ties and I looked into converting the beater to overhead (easy) however, the underslung beater is enjoyable to use.

Varpa's are heavy dense wood, a solid loom and a more compact design than some CM looms.  I liked mine a lot!  Here is a pic from my old blog.

http://bloominloom.wordpress.com/2010/05/11/loom-of-choice/imgp6459/

I inserted eye hooks and use knitting needs through the texolv so I can work above the treadles when tying up.

Dawn

 

 

laurafry

I have very fond memories of Varpapuu Looms.  :)  After learning how to weave here in Canada, I decided to travel to Finland to take some lessons at Varpapuu (held in Kouvola, Finland, not too far away from the factory).  I was there for 2 weeks, weaving every day, meeting weavers from all over the world, and eating great food.  :D

While there we wove on both cb and cm looms.  They all had overhead beaters.  Perhaps this was before they started making the Finlandia model.  (I was there in 1977.)

It was also the first time I'd seen a 'table' loom with the levers at the front of the castle, so I bought one - with stand, which my dh disassembled and carried home in his backpack.  (True love????)  :^)

When he got to customs and immigration in Toronto, the agent wanted him to take the bits and pieces of wood out of his backpack.  He told the agent that he needed a 10 x 10 foot space on the floor and 30 minutes to take the pieces out of his backpack to spread them out on the floor and then an hour to put them all back in again.  And he rather thought that he would miss his flight, but if that was necessary......?  The agent decided that no, it probably wasn't necessary.  He did have all the paperwork for the sale and the brochure from Varpapuu.

By the time I got home 10 days or so later he had it all put together again ready for me to weave on.

I wove placemats (mostly) on that loom eventually earning enough money to buy a floor loom.

Anyway, that doesn't answer your question Ellen, but thanks for the memory.  :)

As I recall the Varpapuu looms were very similar in quality to other looms of similar construction.  

cheers,

Laura

Dawn McCarthy

Here is my "ugly Betty" the Varpa I converted to a drawloom!

Hope the info via private message helped!

Dawn

Joanne Hall

Hi Sally,

What is the weaving width?  And, ask the seller what the breast beam height is.  Both of these will have a bearing on adding a drawloom.

Joanne

SallyE (not verified)

Thank you all for the information!   How wonderful it is to have a place to ask all my dumb questions and get expert answers.  

Dawn - yes the information you sent by PM was very valuable.   I tried to answer, but something happened and I didn't see that the message went.  And thank you also for the pictures!   This gives me faith that I can make it work.

Joanne - What is the correct breast beam height?   It seems that that is something that could easily be changed, up or down.   The weaving width is 48".

Laura - husbands like that are a treasure.   When I mentioned to mine that I was thinking about another loom, his response was "well, we still have rooms that don't have a loom in them!"

Thank you all again!

Regards,

Sally

Joanne Hall

Hi Sally,

When you use long eyed heddles, you lose two inches of your shed.  So, the tie up needs to be carefully done to open the shed further than what you normally need.  That means that the shafts, lamms and treadles all move further.  So, a breast beam height of about 34 inches minimum is necessary.  And the wider the loom, the more the lamms will move up and down.  But 48 inches is fine. 

The other comment I have about the lower beater is that when the loom is wider, it can be more difficult to beat lightly.  I wove on a 60 inch Toika with a lower beater and I could only let the beater beat what it wanted.  It was ok for what I was weaving, but if you want to weave something like curtain or a transparency, you would not be able to advance the warp very far, as then the beater falls onto the fell.  It is easier to control if you advance frequently and keep the fell close to the beater.  This 60 inch weaving width also made the tie-up more difficult and we had to put the treadles very low to have enough space for the lamms to move.

Joanne

SallyE (not verified)

So much to think about!    It has a lower beater, but I will probably move it to be a hung beater.   Dawn did that with her loom, so I could do that too.  I will also need to add an extension to it in the back.   But for a first effort, I'm just going to weave something on it.  That should be an education in itself since I've never used anything but a jack loom.  How exciting!

Thanks again,

Sally

Dawn McCarthy

Sally, mine looks like overhead but that is part of the draw equipment.  I do have pics of the Toika/Varpa overhead set up though and looks easy to do.  I don't mind the underslung (except when weaving a VERY loose web as with my recent Halloweave project) so thus far I have'nt converted.

Joanne Hall

Dawn, that is an excellent beater conversion.  You did a great job.  Congratulations.  I wish more weavers would do this.  It really is much better for the shoulders as well as the weaving.

Joanne

SallyE (not verified)

look like a hung beater!    Thanks for the clarification.

I talked to the women I'm buying the Varapuu from last night.   It was like good karma - she was interested in taking my Barbara IV!  That solves my space problem and means the Barbara will go to someone who is a weaver and not a wood worker.   YA!

keni54

Hi, I've acquired a Varpapuu Kothe table loom, with only 4 levers on top, not 8 as shown in the manual. I also have a separate large flat piece of wood with 6 small flexible handles and eyelets at different angles in a line - of which there is no mention in the manual. As a total beginner to weaving I am wondering what this piece of wood is - and why I have only 4 top levers when the manual shows 8?

cindycraft

Hello -

  I'm a total novice.   I am a knitter, spinner and sock machine crankers so I feel pretty comfortable with fibery things.  There's a Vapapuu Karelia available in my area.   Would the be a loom that's appropriate for a beginner?  

Cindy

midwifehc

I am a beginner as well, and after using a jack loom in a class very briefly, I decided I wanted a countermarch. I have an oxaback that is wonderful and got a steal on a large Varpa, so I bought it as well. I think you'll do fine with the Karelia, especially if you get Joanne Hall's book, which I found very helpful for setting up the loom.

There's someone selling a very nice Karelia at a great price in  my area...where are you located?

cindycraft

I'm in Massachusetts.  The karelia that's for sale is in Rhode Island and it does seem like it's a great price.  I haven't heard back from the seller so maybe it's already been sold?  I'll look for Joanne Hall's book.   What's the title? 

 

 

MaryMartha

CindyCraft, I just got a look at the Karelia.  The pictured loom looks very good, but it is impossible from the picture to count both sets of lamms, or to count the treadles.  I have a smaller version of this loom, which is what I learned on.  I have never regretted the purchase.

Something to keep in mind is that traditional Swedish and Finnish looms tend to have as many treadles as shafts (8 of each, 10 of each, etc.), while newer US-made looms tend to have two more treadles than shafts.  You will find many weaving drafts assume 10 treadles for 8 shafts.  This can sometimes be gotten around by using a "skeleton" tie-up and pressing two treadles to make certain sheds.  Other drafts (8-shaft plaited twills, for example) don't seem to have an 8-treadle solution. For unbalanced weaves, you may have to add weights to the lamms instead of the traditional step of tying up additional treadles.  Joanne Hall's book Tying up the countermarch loom explains all this.

Unlike other small-footprint countermarch looms, like the Glimakra Julia, the Varpa is strong enough for rugs as well as cloth.  If you do buy it, I recommend replacing the bench with an adjustable weaving bench.

 

 

midwifehc

Cindy,

I'm in SE CT, I saw the loom and it's in very nice condition. If I needed it I would have bought it myself. Everything looked complete and was labeled. I weave at the Saunderstown weaving school, which is just a few minutes from her.

Helana

cindycraft

Thank you MaryMartha and midwifehc!  If it's not been sold I think I'll buy it.  It's wonderful to have guidance from people who know what they're doing.  I'll keep you posted on how things work out.  

Cindy

jshea-vaillancourt

Sara I am also new to this site  Icannot get the pm to work

I have read several of your posts and would like  to hear your opinion

I have a chance to purchase a used finlandia 8T 8H  at what appears to be a good price.

this is a major upgrade for me from my rigid heddle

But  I also started spinning watching youtube with a wheel that had been at my Mom's house for 50+ years but never spun during that time

my first spinning wheel was a 30 inch Canadian Production wheel  so not starting too small is a common theme.

The seller  is motivated to not have to pack and move this with her it is however dissassembled

should I just wait  till a more suitable loom becomes available used?

I live in New England

thanks

Judi

 

jshea-vaillancourt

I am in Massachusetts  there is a -from photos  a beautiful varpapuu finlandia  for sale  I found out about through ravelry

This just is a big deal  and a big jump  for size  as a very new weaver  I cannot think I'd outgrow this loom  but should I wait  and go for something smaller

my youngest child is getting married in 1 month so  space for a loom  is not the issue.

just fear I am not doing the right thing

thanks Judi

Ellen (not verified)

I think they are great looms that will last a lifetime and you will not need another loom for the rest of your weaving life.

Dawn McCarthy

It is a great loom, you can weave most anything on, quiet, light to treadle, great tension!

Dawn

jshea-vaillancourt

THank you to the replies I have gotten, while I am a bit scared at what I've gotten into

the 8T 8H finlandia  is dissassembeled ( hope I spelled that right) and sitting snugly up to my first spinning wheel and my yarns.

it looks content  I cannot put it together-I ahve a wedding-my youngest's-in 4 weeks  a1st birthday-my only 1st and only grandchild this weekend  a cake-I should be baking  a dress to alter and oh yes a wedding shawl in beautiful lace to finnish.

so  it will have to sit snugly with my yarn and CPW for a few weeks.

Thanks for all the advice  I am sure I will be asking for more.

Judi

Ellen (not verified)

Congratulations! Oh, it must be hard to have it sitting there, content looking though it is, and not have the time to assemble it and try it out!! But I wish you a lot of happy celebrations in the weeks to come, and then you have this great loom to look forward to afterwards :-)

Dawn McCarthy

The store that I teach weaving at has a Varpa 120cm but the bottom legs are badly damaged, I may offer to "salvage" it but will probably need a pro woodworker to rebuild, Maybe Sally E or Reed Guy can advise?  The rest of the loom is straight and in reasonable condition.  I think the owner is ready to put it to the curb!

celtinbirks

Congrats on your purchase. You may never "outgrow" it.  I got an 8 shaft 10 treadle Varpa Karelia (similar to the Finlandia but with a hanging beater) a couple of years ago and have loved it.  I am a beginner, too, and my Varpa might last me the rest of my life. Have fun!                                                  Candace

celtinbirks

Congrats on your purchase. You may never "outgrow" it.  I got an 8 shaft 10 treadle Varpa Karelia (similar to the Finlandia but with a hanging beater) a couple of years ago and have loved it.  I am a beginner, too, and my Varpa might last me the rest of my life. Have fun!                                                  Candace

Submitted by Anonymous (not verified) on