I have had incredible problems lately with warping.  I warp front to back and the past 2 projects have given me major tangling problems.  I'm not sure what I am doing wrong but this last one I took forever to sley and then thread the heddles.  I still ended up with broken yarns at the heddles and major tangles as I wound the warp on the back beam.  I am working with 8/2 cotton warp, 20 epi in an 8 dent reed.  Any suggestions?

Pam

Comments

philgreer (not verified)

I normally warp back to front.... BUT  the other day i decided to warp front to back and i ended up with a bit of a mess myself.  i put it down to the fact that i don't do it often.  so i know its a really obvious but i thought id ask anyway. have you tried warping back to front? if so how did it go?  roughly how long is the warp your trying to beam? also out of curiosity what brand and style or loom are you using?

cheers

Phil

janenedriscoll

I warp front to back all the time.  As you probably know, keeping the cross intact, is essential to not having the warp threads

tangle.  I'm not sure why you've had difficulties, but it might be because you didn't keep the cross intact.  I have a simple gadget

that I use when i sley the warp that helps preserve the cross.  It is made from a small piece of a 2 x 4, cut into a square.  There

are 4 holes drilled into the wood and thin dowel rods placed into the holes (the dowels are about 3 inches high).  I lash that onto

the front beam and place the cross on it with each end of the cross going between 2 of the posts.  I then lash the warp chain

(about a foot from the cross) to the front beam and thread the reed.  This way I'm sure to take the next thread and not mix up the thread order.  Be sure to thread from one direction (I go from right to left).  If you miss a dent, don't go back and fill in the missing

thread.  Instead move each thread over one to fix the mistake.  If you go back and fill in the missing dent you will get the

threads out of order. 

Hopefully this will make the task of threading the loom much more fun

Janene

Su Butler

Keeping the threads in order with a good 1:1 cross is essential.  Keeping some tension on the warp while you beam it helps a great deal in keeping tangles at bay.  This is the reasoning behind having someone tug and pull at a warp that is being prepared F2B.....but instead of having a human being doing the tensioning (which really doesn't work exceptionally well as how can a human possilbly apply the same amount of tension on an entire warp, you can try adding three well sanded dowels to the tabby sheds behind the shafts and them them act as a "whole loom tension box".  At the front of the loom, add an "S" hook and a filled water jug or other weight that will put some tension on the warp as you beam it onto the loom.  Also, if you lift a tabby shed and prop those shafts up while you beam, it will help separate the threads and allow you to beam with less tangling.  If you can find a copy of Cay Garrett's "Warping All By Yourself", you can learn several very handy tips for putting a warp on the loom F2B with far fewer issues......

Su

claudia (not verified)

Su,

When I learned to beam f2b I was taught to sley the reed from the cross and remove the threads from the cross as you sley.
Then, I turn the reed toward the back of the loom and secure it in front of the heddles and thread the warp while sitting at the back of the loom.  If I left the cross in, it would end up caught between the reed and the heddles.

I'll have to do some reading, I have Cay's book and several others that show this in detail. Maybe I can figure out how to leave the cross in and I would have less of a mess myself.

Claudia

zinniz (not verified)

 Hi Pam, do you have plenty of choke ties on each warp chain?  Since you're sleying from the cross, I wouldn't expect any tangles at that point.  Can you describe what's happening in more detail?  Are you winding more than one end at a time when you wind your warp?  If so--you should maintain a thread by thread cross instead of letting two or more ends go to each arm of the cross.

That's all I can think of right now. 

Carrie.

Joanne Hall

Pam,

If you put two warp ends into each dent, you might want to keep the order by putting the ends on something after you sley then.  You can use lease sticks or just a string tied across the loom.  Then when you thread the heddles, you will know which of the two in each dent is first.

Another thing to be careful about is the tying of the warp ends to the tie-on bar.  Line up all the ends before tying the knots so that the warp ends remain the same length.  Try to use the same length for each knot.  If you use two inches to tie one group and then 3 inches to tie the next, that can cause problems.

If you have problems again, you might try back to front warping.

Joanne

Gemma (not verified)

If the problem occurs at the heddles, try opening a shed -- either tabby, or whichever shed separates the most heddles -- and keep it propped open while beaming on.  My rising shed loom has a castle, so I just tie some of the shafts in the "up" position.  Or, you can weight the treadles.

Su Butler

Hi Claudia.....When you thread from the cross all you are doing is keeping the threads in proper order.  They go from their position in the cross straight through the reed......then you thread a heddle from the threads as they come from the reed.....how could the cross get "caught between the reed and the heddles"??   When I do dress a loom from F2B, I never take the lease sticks out until the heddles are threaded.  At that point they are redundant because the cross - or the threading order - has been kept intact while preparing the heddles.  The warping cross does not caused crossed threads beween reed and heddles....that only happens when the weaver fails to move to the the side of the previously threaded heddle with the new thread or allows a thread to go over or under the previously threaded thread. 

If you put two adjacent threads in a dent in the reed, there is really no need to worry about the cross either, if you thread a heddle, move to the next one and make sure that the next thread is free of the previously threaded heddle.  If the two threads twist together a bit, once you have beamed the warp and tied onto the front, that twisting will only happen in front of the reed, and you can beat it out with the first few picks of the header. 

All that said, you can use the dowels behind the shafts by sleying the reed, theading the heddles and securing the warp to the warp beam.  Then apply some tension at the front of the loom and open the tabby sheds....insert the dowels into the tabby sheds behind the shafts and tie the dowels in place so they will not beam onto the warp beam with the rest of the warp.  Even if you leave the lease sticks in at the front, the cross will be the same at the rear - it has to be......if you threaded the loom correctly....<g>

If you then tie a slip knot or two in the warp, hang an S hook and hang a milk jug filled with water on the S hook, you will have tension at the front of the loom and you can beam onto the back.....all tangles, should any happen will happen at the reed.  If you move your reed towards the breast beam, then beam the beater will fall towards the shafts if there is a tangle.....you can go to the front, remove the tangle, pull the beater forward again and continue beaming......

Hope that helps clarify Claudia....

Su :-)

 

claudia (not verified)

Yup, that's exactly what I do. I maintain the cross until the heddles are threaded then it's gone.  Perhaps I misunderstood the notion of maintaining the cross after the reed is sleyed and the heddles are threaded. When going f2b I remove the cross as I thread.

I do get some tangles if I am using several bouts with different colors. I just finished dressing the loom with three different shades of gray and a bout of supplemental novelty ribbons in white and turquoise. I used the beater as you have suggested but forgot to open a tabby shed so it was slow going and lots of jumping back and forth from the milk jugs and the beater to winding.  I got my exercise last night.

If I had put lease sticks back in, they would have gone behind the heddles and would not have helped with the tangles that occurred in front of the beater, right? Just wanting to learn for next time.

Thanks for the details, Su.

Claudia

lkautio (not verified)

If you are warping f2b you can move the lease sticks to the front of the beater and use them to help tension and detangle as you wind on (behind the heddles is for b2f).  I agree that opening a plain or plainish shed at the same time can be a big help in speeding up the process.

Laurie Autio

Su Butler

Claudia wrote:

>If I had put lease sticks back in, they would have gone behind the heddles and would not have helped with the tangles >that occurred in front of the beater, right? Just wanting to learn for next time.

Putting the lease sticks behind the heddles allows the warp to be tensioned evenly, assuming you don't touch it once it enters the dowels.  Any tangling will occur in front of the reed, and by the method I explained in my last post, you can always have a warning that a tangle is present and correct it before the warp enters the tensioning dowels.

As Laurie has suggested you can have your dowels or lease stick remain in front of the reed as well. If I were choosing that path I would not bother to remove the cross from the lease sticks while threadiing, and so would not have to reestablish the cross in front of the reed.  Instead, you can replace the lease sticks with dowels and the warp will glide pretty smoothly over.  My own experience has shown that I get better tension when placing the dowels behind the shafts, but for years I put warps on the loom F2B by leaving the lease sticks, cross intact, in front of the reed.  Tangles appear at the lease sticks and threads can get caught up in the lease sticks and break if you are not paying attention. 

 

dognapper2 (not verified)

I did a quick search to see if lease sticks were flat (or heavy metal) by design...or for a reason.  This thread seems to have answered that: NO!

I have the Dorothy LeClerc tabletop loom and it came with heavy metal flat Lease Sticks that I have never had very good luck using. They are hard to attach to the loom as they are shorter than the frame, so fall inside. The sheer weight dropped them below the beam no matter how tightly I tried to tie it either side while winding warp on. Plus I tend to thread the loom by the seat of my pants (without a plan) and need to add warp to the sticks without loosing the cross. Untying to add more warp was a pain.

Yesterday I tried cutting a dowel in half, each long enough to extend beyond the frame. I drilled holes in scraps of wood and used them as end caps. It seems to have worked saving the cross while winding on, and was easier to anchor.

How much space should be left between the lease sticks?  I'm thinking these could have been closer, but understanding their function has been part of my learning curve. 

 

Michael White

Hi, it is good to see that you are willing to make modifications to your loom. One thing I would like to point out is your lease sticks need to be able to move. If you get a twist in your yarn as you are winding on the warp and it jams into the sticks your yarn could break. With a set of moving stick you will notice the jam and could address the problem. The space between the sticks really does not matter. They are there just to keep your cross in tact.

Michael 

Sara von Tresckow

 The nicest lease sticks are the beveled lease sticks that usually come with traditional Swedish or Finnish looms. They slide smoothly and the flat design allows the weaver to wiggle them in a way that cuts through slight tangles beautifully. While dowels may work better than the flat, squarish sticks so often sold on table and jack looms, the flat beveled ones are even nicer - have tried both. Also the traditional beveled sticks have holes in the ends so they can be tied to each other and can never fall out.

The tie between the sticks makes a perfect point of attachment - simply run a cord through and tie it literally ANYWHERE on your loom where it works for the part of the process you're currently involved with. When you move to the next step, simply tie them where you need them - including to the back beam when weaving. They are quite useful during the weaving process, allowing, among other things, threads to move several inches right or left of the cross when needed.

Submitted by Anonymous (not verified) on