This may sound like a crazy question but ... I have quite a few spools of carpet warp and wonder if it is useable for items like kitchen towels?  I have been weaving off and on for a couple of years  now but am basically learning through books and experimenting. 

(I have made a few table runners - which turned out fairly decent.  Quite a few scarves - some better than others.  Have mainly used knitting yarn for both warp and weft on the latter.  Did use some rayon that I bought at a weaving shop for two scarves but found it difficult to work with because of the fineness of the thread?  I did finish both projects but wasn't extremely satisfied with it?)

I am wanting to use the carpet warp/thread to make kitchen towels but am uncertain about the sett needed?  From what I can figure from what I've seen others post, I probably need to rewarp my loom for a closer sett.  I currently have it set at 12 epi.  Do I need to set more at 24 epi to get a closer/tighter weave? 

Can I successfully use the carpet warp for both warp and weft? 

I know this is all very basic but my head is spinning trying to figure it out.

Thanks for any help or suggestions.

 

God bless.

Comments

Su Butler

Not a lot of help, but I remember an issue of HANDWOVEN that featured towels woven in carpet warp.....the weaver claimed they were soft and absorbant.  To find the proper sett for plain weave, wrap the carpet warp around a ruler, butting the edges of each wrap side to side but not overlapping and count how many threads occupy one inch.  Then divide that number in two for plain weave.  For twill, use the number of threads that occupy 2/3 of the inch measure as a place to start.  Then, of course, sample.  You can wrap some cardboard with the yarn at different setts and needle weave to find out if the sett you want will work.  Wet finish the needle woven pieces and you will find the sett that pleases you most.  Or you can sett a loom with a narrow sampler, with samples set side by side at 8 epi, 12, epi, 16 epi, 20 epi and 24 epi.....weave a few inches, then cut and wet finish.......

All that said, I would think 12 epi too open and 24 too dense......I might opt for 16 epi to start......but you will need to sample to make sure the final sett is one that pleases you and creates good cloth.

Happy weaving!

Su

lkautio (not verified)

The carpet warp should be okay for heavy hand towels, but maybe not the thin type for drying fine stemware.  If it is the common 8/4 carpet warp it is  equivalent in size to a 4/2 cotton yarn, with plain weave setts of about 14-16, and twills in the 16-20 range.  It should make excellent runners and placemats as well.  Su is absolutely right about the sampling.  Also if you end up with a piece that feels nice to you but is unbalanced - say 12 in the warp and 18 in the weft, just average the two and resley - here to 15 epi, which should give nice results with a 15 ppi weft.

cheers,

Laurie Autio

suzyhok (not verified)

Carpet warp does make really nice soft hand towels, but be careful of it bleeding.  I made some towels with white and red 8/4s and when I washed them the red bleed into the white.  Frustrating.  So... try washing some of the yarn before... to see if it's color-fast.

Have fun!

d chafin (not verified)

Am a relatively new weaver and have some carpet warp on shelf and would like to weave some towels. Didn't know about absorbancy. The comments above were helpful. If anyone out there has input I'd appreciate it. D

laurafry

Personally I would find carpet warp too thick for dish towels and would be more inclined to use that for placemats or table runners (mug rugs, etc.)

As for absorbency, it would depend on how tightly the fibre has been twisted.  More twist = less absorbency.

Cheers,

Laura

d chafin (not verified)

Thanks Laura. I like the idea of mug rugs. I'm in a stitch group and ready to make 8 ladies their Christmas gifts. None of them weave so I like to weave something for them. D
Submitted by Anonymous (not verified) on