I recently attempted to weave the bamboo meets angora scarf in Handwoven Jan/Feb 2007 page 28 on my wolf pup.  After weaving  I discovered my horizontal stripes were not weaving properly.  After investigation I realized I threaded my warp wrong.  Instead of threading my first thread on the heddle closest to me (sitting in the back of my loom) I threaded my first thread on the heddle closest to the beater.  I did this all the way across.  So my question is there a way to continue weaving and get my stripes without unweaving and re-threading? 

Thanks for any help!

Karen O

Comments

Claudia Segal (not verified)

Hi Karen,

If you have any pictures or can give me more information about the draft that would be helpful.  I don't have a copy of that issue of Handwoven so it's hard to guess at what is happening.

Claudia

 

Michael White

I am going to take a wild guess and say try treadling your loom in the reverse order then what is written. If it says 1,3 2,4 do it 2,4 1,3 maybe this will help. Question, what does the underside of your cloth look like? You could also download free weaving software (see this talk elsewhere) and play with it.

Remember, everyday is a learning experience.

Michael

Ruby Leslie

Karen, the scarf is threaded in a 4-S straight draw and treadled as a 2/2 twill. It sounds like you threaded it 1-2-3-4 rather than 4-3-2-1, which only changes the direction of the twill line.  What is it about the horizontal stripes that isn't working out correctly?  Ruby

kob250 (not verified)

Thank you so much for answering. Yes that is exactly how I threaded.  The horizontal stripes are just like dots and not like the vertical white stripes which look like a twill.  The underside isn't any better.  The black twill looks fine.  Someone suggested reversing the order that I treadle which I'll give a shot at.  Thanks again.

Karen O

kob250 (not verified)

Thanks Michael!  I am very anxoius to try your suggestion!  I HOPE it works!  I will let you know!

Karen O

kob250 (not verified)

Hey Michael,

Thank you for your suggestion...I am very excited to try it out!  I hope it works.  Will let you know.

Karen O

kob250 (not verified)

Thanks Claudia,

It is a straight draw with a 2/2 twill treadling/  I threaded 1 2 3 4 instead of 4 3 2 1.  I'll see if I can send a picture, not so good at this computer stuff!

Thanks Karen O 

tien (not verified)

I believe what you actually need to do is to reverse the sequence of the tie-up, so that if you were supposed to tie up shaft #1 to that treadle, you should now tie up shaft #4 to that treadle. 

In the threading, you have:

Original      --> New

Shaft #1 --> Shaft #4

Shaft #2 --> Shaft #3

Shaft #3 --> Shaft #2

Shaft #4 --> Shaft #1

So in your tie-up, you need to switch things around the same way.  If you were supposed to tie shaft #1 to a treadle, tie shaft #4 instead; if you were supposed to tie shaft #2 to a treadle, tie shaft #3 instead.  And so on.

I think that should give you good results...I'm not 100% certain of this since I'm not near my weaving software at the moment, but I'll check when I get home.

Ruby Leslie

It sounds like you're beating too hard.  You don't need to change your tie up or your treadling order.  As long as you threaded it straight draw, and treadle it as a 2/2 twill, you'll get a 2/2 twill.  The direction of the twill line will be opposite to what was shown in the draft, but it should still give you the horizontal stripe results of the photo.  If you beat too hard then you'll be squashing the weft into tight, packed dots.  Check your ppi and beat with a lighter hand.  Ruby

Submitted by Anonymous (not verified) on