It is finally in the studio. A barn frame loom that has been in storage for too many years is on its way to a new life. One that I hope will include some travel and demonstration of traditional weaving. My goal is to eventually put a simple overshot pattern on this loom to demonstrate how to create beautiful items with the tools of the day. There is a long way to go before this will be ready to make its debut over Memorial Day weekend. I am looking for information on a couple of components such as the weight for the back beam. I have noticed on several of these old looms that the wood bar that slides into the holes on the back beam to hold the tension is weighted. Being resourceful the early pioneers used what was available or they were able to get. I would be interested in seeing photographs of the various types of poles/weights used for tensioning. This loom is missing this pole/weight. I can think of a variety of modern items to use, but I want to stay as authentic as I can so therefore barbell weight is not an option. I am missing the large dowel type piece that the harnesses hang from, however I have access to replacement parts that I can adapt so that at least I won't have to replace with new wood. There are no rockers/horses with these pieces to hang the harnesses, would be interested in photographs of what is working for you all. I have looked at this type of loom for years in my travels and while I have often photographed them, I find that I don't have the closeups of the parts that I'm interested in. Any input and help is appreciated.

Comments

Sara von Tresckow

The warp beam was held in place by a stick, rod or pole stuck through the holes and braced against the frame. There are multiple holes so by advancing the stick can be moved to another position.

Weights would have been used if the loom was used with "live weight tension" and you'd need to look at Kati Meek's book for how to do that.

Authenticity? The old weavers used what they had - so if you do the same, you'd be authentic.

We sell horses and pulleys to hang the shafts for counterbalance looms.

www.woolgatherers.com

sally orgren

I took a tour through RI over Labor Day, which diverted to Plimouth Plantation and Sturbridge Village in MA, along with a stop at Slater Mill in Pawtucket. We took lots of details photos of all the barn frame looms we could see! So, I will try and post a few images here, but may have to send to you privately. (I think this site will only let me post one image per day to a forum).

P.S. I was near Wheeling, WV last week. Is that any where close to you?

Slater Mill Loom:

sequel (not verified)

That diagonal thing you see in the back in the brake on the museum loom.  I worked on a loom that had only one hole all the way through the warp beam and the pole that was used to crank the beam was also the brake, which was engaged with a rope from the castle, fixing it in place so it would not advance.

kerstinfroberg

I have a couple of pictures of traditional tensioning systems on my blog, here.

The first picture here shows how simple a "horse" can look. The third pic shows a five-shaft pulley used for 4 shafts.

 

sequel (not verified)

The first loom shown on Kerstin's blog is like the one I worked with.  Only instead of a notched board, mine had an adjustable rope to hold the rod in place!  If I can find an old pic of the loom I'll show you.

sally orgren

(Slogging away by posting one photo per day here...)

The reason why I was taking detailed photos of these old looms is that on our 1700's barn frame loom, the shafts has always hung wonky, just like many of these do. We are trying to figure out why, and correct it if we can.

Also, many of these looms have ties at the end of the shafts, I suppose to keep the unused string heddles from "falling off". But my colleague says that is not the typical way it should be done, there should be a string running along the top that captures all the heddles (assuming they are not already "knit" together) and the holes on each end are for securing that string. I understand Swedish looms are set up this way. So the top and bottom of each shaft is suspended only by the heddles, not strings on either end.

We have been debating if tying the shaft ends as shown above has any consequence in how the shafts perform? Thoughts?

(More photos to come. Patience!)

sally orgren

Our brake system on the 1700's loom is similar to the Slater Mill loom, but with a difference. We have similar wooden pegs on the right side of the back beam, and there is a stick that drops down (at an angle) and lodges between those pegs to hold the beam in position (just like the Slater Mill photo). But moving forward even one increment between pegs is a large unit of measurement at the front when advancing the warp.

So, at the front of the loom, right side, nestled inside the frame, we have a thin metal bar with a flat flange, and a metal wheel (rachet) with small teeth in maybe 1" or less increments. This is how we can "fine tune" the warp tension at the front. (Never occurred to me this could be a saw blade!)

For additional adjustment on these looms, the beater and reed is not in a fixed position. Along the top frame of these looms, you can usually find groves, pads, nail holes from wooden attachments, or some type of indication that the beater could be repositioned into a few pre-determined areas. This allows you to lift and position the beater to get the right angle on the fell line, because advancing the warp with the other two methods still might not allow you to have the fell line where you need it.

If you can implement live weight tensioning, that would be a dream for anyone weaving in a demo situation. One of the problems we have is our volunteers don't like to weave on our 1700's loom. I suspect because the loom is too fussy, the shafts hang wonky, and the treadles are floppy. And it can be annoying to figure out the sweet spot with so many adjustments right when a bunch of visitors arrive!

Joanne Hall

Print out the instructions from our website (written below) and give them to the museum.  It will make a big difference in their understanding and they will then solve their problems and enjoy weaving on the loom.  However, the top pulley is far too big.  It makes the shafts hang too far apart.  If they are not an original part of the loom, find smaller wheels for the pulleys.  Having the shafts closer together will give much better sheds.
http://glimakrausa.com/learning-looms-weaving/intro-to-countermarch-and…

Joanne

kerstinfroberg

It is not easy to tell, but to me it seems like the back lower pulley holds 2 shafts, while the front lower pulley is a, hm, "two-tier" pulley even though it only holds 2 shafts?

Whatever - in my opinion, horses (rockers, what-have-you) have a better stabilizing effect than using pulleys everywhere. I may be wrong - it can be just *my* prejudices talking ;-)  (And I agree w Joanne - shafts closer together will give better sheds)

Also, in my opinion, the slanting warp will always be a problem. The shafts, however well balanced, will always tend to wander forward (and, because of that, disturb the balance). The times I have used a loom w a slanting warp, I found myself pushing back the shafts all the time (as in maybe every 10 picks... most tedious).

However: on all(?) "standard" Swe looms, the beater can be adjusted both in height and along the warp. This doesn't mean it *has* to be constantly shifted (even though I have read non-scandinavians "rave" about that "feature"). As an example, I may be shifting my beater backwards when on the last inches of warp, if (and only if) I really, really want to get that last 1-2 inches woven. Typically I *never* shift the beater... (Again, see the pics here, this time the 4th)

Holes in the shaft bars: yes, holes in the bars are for securing the heddles to the (individual) bar. In most Swe books there are instructions to "tie a half-rosette at each end of the bar". Many years ago I got the BEST tip ever about that - see my website. (This method works for ALL "sticks" that need securing - from lease sticks to heddle bars to front (or back) apron rods. Now I never drop a heddle, or a lease stick, or - .

And... remember to have fun!

loomyladi (not verified)

Excellent Resource.  A quick read gave me lots of information.  I have often been frustrated at having to get up to advance the warp on an old loom I weave on often.  Now I know that I can move the beater - - I wondered why those metal teeth were there.

loomyladi (not verified)

In this poor photo (morning light great for weaving, but lousy for am pics), I have temporarily suspended a childs broom (insert plug for Lone Oak Brooms from PA, purchase your very own at Maryland S&W) so now I know what size dowel to locate for this missing piece, how far below this cross piece (is there a name for it?) do I hang the heddle sticks? There is a string showing in the lower right and that will be the warp path from back to front so that is my target for heddle eyes. Thank you all for the input, this is extremely helpful in this project.

sally orgren

Again, wonky shafts, same pulley system on top (not rockers), tied at the sides of the shafts. 

-----------------

Loomyladi, comparing your loom to these photos, I think your back beam needs the pegs inserted, and it might need to be flipped over so those pegs are on the right side of the loom, as you are facing the loom.

Also, where there are two square holes near the top of the back frame, left and right, that is where our 1700's loom has a built in raddle. (I will continue to add photos, have not posted that one yet)

I can't tell from the backlit photo, is your string on top of the beater? (Wouldn't there be a reed between the top and bottom of the beater, and the warp path needs to fall in the center of that?)

Looks like you are on the right track! Can you borrow or buy the Lila Lundell Big Book of Weaving? (It has great illustrations.) 

Joanne Hall

It is important to remember that counterbalance shafts are held by the warp.  The warp needs to be tensioned and you also need to depress a treadle before the shafts will hang in the correct position.  So, do not think that there is a problem if you are not actually weaving the sheds.

Joanne

Joanne Hall

The instructions for assembly of the shafts and determining the height of the shafts and beater are in the file I sent to you in a previous message.  It is not hard to do, but it is usually done after you put the warp on.  The tie-up for the shafts is easy to adjust for height.  And most of these looms allow you to adjust the height of the beater.  So, you do not need to do this until later.

Joanne

loomyladi (not verified)

Sally - Reed is in the beater (love the light/hate the light, purchased winter drapes today - - sighhhh, will miss the light but need the warmth). The back beam has been repositioned correctly and the holes have been filled with the back support.

sally orgren

Your restoration project is helping me collect thoughts about what I'd like to try to get our loom weaving a bit more smoothly, so more volunteers will try it! And being able to post these photos of old looms in one place hopefully with help others if they search the forums.

Here is the loom our guild works with in western NJ, Delaware Water Gap National Recreation Area, Millbrook Village. 1700's, purchased in Bucks Co, PA (probably in the 1970's) and it originally came from CT, but that is all I know about it.

In this photo, the shafts are adjusted to look fairly equal, but after a few moments of weaving, they go wonky. Since the photo, we have beamed a new warp on this loom, and the shaft irregularity effects the shed on one side, so I would like to correct if possible.

In looking at the photo, I see I was wrong about the raddle placement. A cross piece is positioned in the top hole across the back frame of the loom. The second piece of wood (that falls at an angle) is the back brake that lands between the pegs of the warp beam on the right. The third piece that goes across the back is the raddle. (In the photo you can barely see it—it appears just above the front top piece of the loom.) This loom still has a reed reed, almost all original parts, and the few the Park Service replaced are easily identified. (FYI, at the Weaving History Conference in Clayton, NY this spring, someone was selling reed reeds for $10 apiece.)

At the lower right of the front beam, on the inside, you can see the ratchet brake with fine teeth. (Maybe an old saw blade? I'll have to look more carefully next time!)

There is a cord (with a loop) that goes from the lamms to the tip of each treadle. There is no way to affix the loop up or down on the treadle tip, so it tends to migrate. The treadles have a lot of left-to-right movement too, you have to sort of have to "shake" them apart with your foot to be sure you are treadling the right one(s). I don't think that "floppiness" makes our volunteers very happy, but maybe that is the way all these barn frame looms weave with the treadles so close together?

loomyladi (not verified)

The photos and discussion are VERY helpful.  I will have to dig out photos I have of this wonderful old gems.  Haven't had the time to digest everything this week.  Hoping to reread and evaluate more closely tomorrow evening.  From the posts on this and other barn frame loom projects, perhaps we should have a Barn Frame Loom Group?

loomyladi (not verified)

The photos and discussion are VERY helpful.  I will have to dig out photos I have of this wonderful old gems.  Haven't had the time to digest everything this week.  Hoping to reread and evaluate more closely tomorrow evening.  From the posts on this and other barn frame loom projects, perhaps we should have a Barn Frame Loom Group?

kerstinfroberg

"shafts go wonky"? What is "wonky"? It looks like the (position of the) cords will drag the shafts a bit to the right (or left)?  I think that the point where the pulley cord attach to the shaft(s) is of importance. When using horses, it is important that the horse-to-shaft cord is attached at the point where it is perpendicular to both to the shaft and to the horse. In the pic it looks a bit "well, it is good enough"? What happens if the cords are positioned more carefully? Sometimes, when using narrow warps (usually, "narow" means narrower than this), it helps using elastics looped around the shaft ends. (Or is the warp slanting? If yes, maybe that is the problem.)

"There is a cord (with a loop) that goes from the lamms to the tip of each treadle." ? Does this mean there are no holes in the treadles? Anyway, I don't think that is the reason of the "floppiness". All ("most"?) of the old looms I know (incl my own old cm, first pic) have "floppy" treadles. (And so has my new-ish Glimåkra, come to think about it) So: yes, I think that is a characteristic of "all these barn frame looms" - or, maybe, "all Scandinavian style looms". I know I miss the, hm, "floppiness" (sideways motion) when weaving on my folding Göta, which has a) front hinged and b) very short treadles. "Practice makes perfect" ;-) ? (I don't mean that, exactly. As Laura F once pointed out, practice only forms habits - but: knowing to expect different behaviour from different looms forms different habits - methinks it is too late for philosophic reasoning - hope I make myself half-clear)

sally orgren

In the photo of Hill House loom, the shafts are nearly level for the photo, but if weaving, one shaft would quickly get out of this alignment.

When I wrote "wonky" I meant one or two shafts are no longer parallel to the floor, one shaft edge raises up quite a bit (as seen in some of these other historic loom photos). This may cause the narrowing of the shed on one side as those warp threads won't lift as much on the "down" side.

In the photo of the Hill House loom, it does look like all the shafts may be slightly higher on the left. ("Good enough" positioning?) When weaving, it is one of the shafts that raises up on the right that creates the problem. (I don't think the warp itself is higher on one side.) Not sure exactly which shaft without being on location and starting to weave...

If you could, where would you suspend the pulleys in relation to the warp? I also need to check the top of each shaft. I think there are holes drilled to hold the cords that go through the pulleys, so I didn't think we thought we had a choice where to put the pulleys in relation to the shafts.

I think we DO need to address the original hanging of the pulleys. The cords were handspun, plied linen. The weaver who set up this loom 30-40 years ago passed away in February at 97. She felt perhaps that wasn't the right material to have used. Also, the pulleys were hand-carved by contemporary woodworkers at the village. I think they were done in the "old timey" spirit, not the "fine craft" of reproduction. (i.e. they may not have a smoothest of movement.)

No holes in the treadles. Even small slats of wood attached to the bottom of the treadles or grooves would keep the loops from migrating upward toward the tip of the treadle. But the loom is owned by the National Park Service, and I don't think we are allowed to make a permanent adjustment like that. (We speculated that the loops should possibly be staggered, not all hang down and land on each treadle tip in the same place.)

Another issue: there are wedges of wood added to the bench to tip it inward. The original person who regularly wove on this loom was very short. Some of the current weavers complain about the uncomfortable pitch. What was standard for these looms? In all my photos, it looks like the benches were flat. The wedges were added later, so not a permanent part of the original loom. (They could be removed, if that would get more folks to weave!)

----

More photos—Pawtucket Loom, lamms to treadles. (no warp on this loom at the time of the photo.)

kerstinfroberg

When I went to weaving school (and in all Swe weaving books I have read)we are told that, going from top down: the highest pulleys, those attached to the top cross member ("the heddle ... beam" solv-stång, thus the place where the garness is suspended from) at 1/4th from the ends, regardless of warp width. (1/4 - pulley - 1/2 - pulley - 1/4)

I have (nearly) never used pulleys instead of horses, but for horses the rule of thumb is that they should hang one heddle-height over the heddle-bar - this is easily achieved by using heddles for the cords: just lark's-eye them first to the heddle bar, next to the horse. However... as the horses themselves give some movement, I don't think that "rule" can be used if one is using pulleys at the lower level. My guess is that pulley cords must be longer (hiw much? no idea...)

Whatever method for suspending the heddle bars, the point of attachment should be straight under their attachment point. (If using horses - drag one horse down to the heddle bar, and make note of where the points fall. Again, for horses: remember that hoses have to be tied "opposite" on opposite ends. If left side front horse's left end goes on front shaft, then right side front horse's right end must go on front shaft.) For pulleys I imagine the cord must be positioned exactly under the pulley - or, in your example, with holes in the shafts, the upper pulley must go exactly over the holes in the shafts. (I hope I'm making sense!) (Hm... you could, of course, try with horses - a straight dowel, can be flat, a hole in the exact middle, a little carving to hinder the cords from falling off. Can be made more facy if wanted..)

It can help to have a few free heddles towards the end of the shafts (or, I suppose, tie a cord between the bars - but then that cord has to have the correct length, or it will not help in stabilizing anything). It can be a problem to have *a lot* of unused heddles on the shafts, esp if there are (say) 50 empties to the right on shaft 1, no heddles to the left, and (say) the reverse on shaft 4... you get the picture.

On your last pic, the one without a warp: the "lamms" look to be free-hanging? In Sweden we don't call that a lamm, we call it (confusingly) "horse", or "shaft horse" (but then, the upper horses are called nickepinnar, more-or-less "nodding dowels", so for us that isn't a problem :-). Anyway, these extra dowels are generally tied nearer to the shaft bar(s) - 2-3 cm?, to help distribute the downward pull of the treadle cords - exactly as you have done. But it looks like the nearest "lamm" is not tied symmetrically? Again, to get balance, all "shaft horses" have to be tied symmetrically. Positioning is important!

Or... you could try another option: take avay the lamms. Tie the correct number of treadle cords (2?) to the middle of the shaft, pass the cords through a ring (any ring, a piece of cow's horn or just a ring of yarn) and proceed to tie cords to treadles. In your situation (no holes in treadles, I suppose you have to do that in reverse...) - I have never heard/seen a loom with treadles without holes! (well - but then they had screw eyes or something instead)

Remember that 1. there HAS to be a warp on before all tieing(sp?) is done and 2. shafts HAVE to be (and stay!) stabilized until all treadle-tieing is done. Only then can the sheds be evaluated.

Benches: are these built-in benches? I hate them... may look good, but are useless - unless you happen to be the correct size yourself... Yes, flat. However, what a relief it was when Öxabäck started to make slanting benches, you could almost hear the sigh of contentment from weavers all over Sweden ;-)  Perheps everybody could bring their favourite pillow? Or... your next project: custom-made bench pillows! Our nat'l guild had a competition in '09 - here is the winning draft (a .pdf, and, as there are no description of how to sew it, y'all should be good with what little Swedish there is)

If you ever need a consultant "on site", I'm game! I could donate my time, in exchange for flying fare, lodging and board ;-)

 

sandra.eberhar…

In looking at the photos, I am struck by the lack of symmetry.  The heddle bars aren't even with each other, the pulleys don't seem to be attached symmetrically to the heddle bars, the lams or treadles may not be attached to the middle of the heddle bar, the heddles aren't in the middle of the heddle bar.  All of these things will unbalance the heddles.  I had similar problems with my barn frame loom when it was a counterbalance, and spent an afternoon getting everythink centered and symmetrical.  The balance is key.  Rollers instead of pulleys or horses help keep the heddle bars even because you can put a screw in the middle of the cord to keep it in place.

Slipstream (not verified)

This thread got me to consider some of the various shaft pulley systems I've seen and what might be the problem with shafts not being level.  In many of the old looms I've seen the shafts are held up with either pulleys of horses.  In the Worth book on foot powered looms the method Worth uses to hang the shafts creates a couple (technical term I'll address in a moment) between the two sides of a shaft.  The two ends of the shafts are coupled using a wooden rod of the appropriate radius to allow the shafts to hang free of each other but by taking a second loop over the rod the shafts do not swing free on the ends.  The loops around the rods that allow the shafts to raise and lower provide friction and the rod keeps the shaft st the same height troughout the rising and lowering of the shaft by coupleing the two sides. You do not have the same couple when you have two independant pulleys or a horse systems at each end of the shaft. The horses actually provide a better support and registration of the shafts because the cable attached to the horses can't travel since the length is fixed and it can only travel the length of the horse's swing. I'm not sure if I've helped or not, I'll try and upload a video (can I do that?) of a barn loom I'm working on which has the pulley system and I'm converting it to a rod system because of this exact problem.

Regards, Charles

kerstinfroberg

Charles, I may be misunderstanding, but... You write "The horses actually provide a better support and registration of the shafts because the cable attached to the horses can't travel since the length is fixed and it can only travel the length of the horse's swing." This I interpret as if you think the horses always hang at the same level (if that isnä't what you are saying, disregard the rest of this post).  The horses can travel up and down, and also swing from the pivot the cord makes.

On a tabby shed (1-3 vs 2-4) the horses essentially stay on the same level, but for other combinations they don't. See for instance photo 8 of my project "Counterbalance loom sheds". If you enlarge the photo, it can easily be seen that the back horse sits higher than the fromt one, which is also tilted.

(if I misunderstood, I apologize!)

Slipstream (not verified)

Sorry multiple post, I have no idea how this happens.

Slipstream (not verified)

Sorry multiple post

Slipstream (not verified)

Sorry multiple post!

Slipstream (not verified)

<p>I do believe you misunderstood but the fault resides in my explanation. &nbsp;I understood what I meant, I just didn't do a great job of explaining it. You are exactly right. what I was trying to say was that the horses were better than the pulleys because the cable can ride up and over the pulleys unevenly and get out of adjustment where on the horses, since the cables are attached to hard points they can't get out of adjustment. In my opinion the best system is one that uses rods instead of pulleys because the rod, being solid does not allow the cable to ride up and get out of registration especially if you take a loop or two over the rod. &nbsp;I sometimes find it difficult to explain a concept without being able to sketch it. &nbsp;Years of being a mechanical engineer didn't do a lot to help my descriptive language skills, it's always easier to just sketch out a concept :)</p><p>Best regards, Charles</p>

kerstinfroberg

In my opinion, admittedly based more on "thinking" than on practical experiments, a top pulley and two horses is better than two rollers. I have misplaced my calculations (done years ago), but I think the added degree of freedom(?) that comes from the "nodding" horse helped for uneven sheds. (That uneven sheds can be done I have known for... 35 years? - but: why all this talk about shed regulators in the US?)

- not quite just rambling, but maybe I'll be more, hm, exact after dinner?

loomyladi (not verified)

It took longer than I hoped (doesn't it always), but the loom is in working order. Granted I only have 2 harnesses at the moment, but I have woven on it. I'm so excited! I need to sand the last two sets of heddle bars then connect, adjust horses and harnesses and I will be ready to warp a coverlet. I still have not made up my mind on a pattern, but I have at least another month until that is an issue. Thanks for all the words of wisdom.

peggychurch (not verified)

I am setting up a barn frame loom for a small museum.  There is an inch wide groove in the cloth beam and a stick that fits in it.  This makes me think the stick should be in an apron pocket and fitted into the groove.  I think the apron should be long enough to wrap around the cloth beam a couple of times to hold the stick in place.  Can anyone comment on aprons versus cords?

Sara von Tresckow

Actually, those grooved beams were meant to have the stick simply placed in the groove - in the case of the cloth beam, you'd use beam cords at the start of the project, and when the stick reaches the beam slot, the beam cords are taken off, the stick set in the groove, and the cloth will wind on smoothly.

The warp beam can (and often did) have the same construction - there, the stick was placed directly into the slot until the warp had been woven and beam cords were then attached to allow the stick to move forward and save on loom waste.

Aprons are not used with this type of beam.

peggychurch (not verified)

Sara, thank you for the response.  I had no idea to set it up this way.  Can you advise me on how to attach the cords.  I don't think there are holes drilled through the beam for cords.  

Sara von Tresckow

No, there won't be holes in the beam. You simply sling the cords around the beam and the tieon bar so that it is supported as it moves forward - sort of like lashing on when you do the overhand knots. I have some photos, but they are dark and not really clear - this is a great way to have the warp on straight (in the groove) as well as having the cloth wind on smoothly without distortion. 

peggychurch (not verified)

I can visualize very long lashing on cords, from the cloth beam to the tie on bar.  But it seems the cloth beam would just rotate within the lashing.  Do the cords go around the stick, then the stick is put into the slot in the beam?  That would anchor them to the beam if I tie the stick into the slot.  This appears to be a two person project.

ReedGuy

Had a look at an old counterbalanced loom on the weekend. It was not complete though and the wood, of what was there, was checked badly and the end of one piece was rotted with powder post beetle holes. But at any rate, the back beam was rather peculiar. It had wooden rounds/wheels on the ends that were at least 18" diameter. They were wider than the main beam between. And the main beam was made of lathed maple rollers, the kind found on old roller tables used by potato farmers to grade potatoes for market. It was a very heavy beam. It was turned by a handle that was removable and probably used on the cloth beam also. Heavy maple and thick.Ratchet and pawl was on the inside of the loom. The beater was like a Swedish design, for overhead, with peg holes to adjust up and down. But it was missing the cross bar on top that the uprights slip up through. The top cross member was there and the pulleys. But in the middle of it was subtended a tray like piece, maybe for scissors and needles. There was a second cloth beam, or two the same size anyway. The frame construction was mortise and tenon, but was held by irons, not wooden pegs or wedges. The warp beam was released with a lever from the front where the weaver was seated, like some of the Leclerc looms. Everything was left handed. There were four treadles, front mounted. Looked like a direct tie-up. There was also a home made warping board, that had been nailed to a wall I would say. Had old square cut nails and lap joint cut out where it would have been mounted to wall studs in a shed. The family said the loom was a great grand mother's of the owner (he is 66 I think). No one has woven since the old woman used it. They thought 170 years old, but I'm thinking late 1800's or early 1900's because of the irons. Never seen anything like it online yet. Sure was rugged.

Submitted by Anonymous (not verified) on