I recently bought an old loom that had sat in a storage unit for 20 years.  Obviously the loom needs some TLC to be brought back to life.  I'm in the middle of that.

As you might imagine, the old carbon steel reed was rusty.  Knowing that I had nothing to lose, when my son offered to sandblast it, I took him up on it.  The reed now has absolutely no rust but feels a bit chalky.  My son did blow a lot of air past it after the sandblasting.  I've dusted it with a swiffer but that hasn't made a noticeable improvement.

Any suggestions on how I should proceed?  What do you think about spraying it with silicone?

Thanks for your insights!

Peg

Comments

SallyE (not verified)

Sandblasting removes material by shooting sand (silicon carbide is what is in my sandblaster) at it.  But those same little particles also make pits in the materials.   The finer the blast media, the smaller the pits.

So while the rust may be gone, you are left with pits.   Whether they will be a problem or not depends on the size of the pits and what you want to weave.  Fine silk might be a problem.   Large, course wool, might not be a problem.   I'd take a few threads of what you want to use as warp, pull them through the reed and see if they snag.  If they do, you can't use the reed.  Even if it doesn't seem like it's a problem, you warp is being abraded by those pits as you use the reed.

A naval jelly would have worked better to get rid of the rust.   But, since you don't have anything to lose, you might try a light spray of lacquer for metal.  Once you have sprayed it on and before it's dry, use a soft toothbrush and brush up and down pushing into the dents, on both sides of the reed.   This will make sure the lacquer is evenly distributed and there is no build up anywhere, and it may fill in some of those pits.  This will also keep the reed from rusting in the future.

 

Peg.Cherre (not verified)

Your ideas make sense.  I do tend to work with fine-ish threads - usually 8/2 or finer, with lots of rayon & bamboo-they don't like abrading.  I did know that there was a possibility that the sandblasting would be problemmatic, but I'd done the naval jelly route on a reed before & wasn't going to do it again; I planned to buy a stainless one.  So if I can make this one work with a spray of laquer, fine.  If not, I've not lost anything. 

Badfaerie (not verified)

I'm not sure lacquer will work, but ask your son if he can soda blast it. It's a similar process to sand(media) blasting, but uses sodium bicarbonate (baking soda) instead of the sand/glass that the sand blasting process uses. It would have been the better first choice since it tends not to pit at all, but it may smooth out the finish left from the sandblasting.

SallyE (not verified)

Interesting, I've never heard of blasting with soda.  If it doesn't pit at all, how could it possibly smooth out pits?   It would have to remove material to smooth out pits, and if it could do that, it could also pit it.  Also, changing out the sand to use soda is not a small task.

But I'm curious- what is soda blasting used for?

 

sequel (not verified)

Ground walnut hulls are used in some situations when blasting with sand is too abrasive.  Soda blasting sounds like it is even less so.  These are often used to polish performance automotive parts.

Badfaerie (not verified)

http://en.wikipedia.org/wiki/Sodablasting

We've used it for delicate restorations on everything from treadle sewing machines to plastic parts. We use it a lot for final prep for motorcycle parts before powdercoa paint. It is a very similar process to sand blasting but has 3 key differences. One, the particles being blastedare significantly smaller. 2K+ grit comared to 500 grit for a fime sand media.

Second, there is a chemical reaction as well that helps to remove grease, rust  and other chemical agents.

And third, it's cheap and non-toxic.

I don't think it would remove the pits, but it might smooth the sharp edges of the pits left by the sand blasting.

 

SallyE (not verified)

Wow, thanks.  I never knew that!

 

Peg.Cherre (not verified)

I did try Sally's suggestion of spraying with clear lacquer - actually I used a clear polyurethane.  I had nothing to lose and was prepared to buy a new reed if needed.  I sprayed on one side, brushed a bit with an old toothbrush.  Let it dry, sprayed from the other side & brushed a bit again.

I've since used the reed a few times, one with a loosely-twisted Bambu7, the other with a 10/2 rayon.  The reed worked fine.

Thanks for the ideas, weavers!

Submitted by Anonymous (not verified) on