TinaHilton (not verified)

I don't weave that many rag rugs, so this may be wrong, but I thought it was better to cut along the length of the fabric rather than from selvedge to selvedge.  Strips cut crosswise (selvedge to selvedge) will stretch more because the fabric stretches that way. 

claudia (not verified)

Hi Jennifer,

I have found crosswise strips to lay in better and the edges shred less, another benefit if you don't feel like turning under both edges.  

I was very upset when my 8/4 carpet warp threads began popping so I switched to very firm 12/6 carpet warp from Glimakra in a natural color.  It's here or just click on their ad on any page.  I have also doubled the 8/4 carpet warp and dropped my sett to 8 from 10.  Nothing popped but the 12/6 works much better.  

I also cut men's ties for weft and made a purse with carpet warp which you can see here.

Claudia

Rugsbyjoe (not verified)

Hi Jennifer Most of the time when a "tabby threaded" is used is when the weaver is weaving a rag rug that would be "log cabin" "munks belt" or some "overshot" In useing a thbby thread the weaving is not as tight as when a rag rug is woven with out a "tabby Thread" the rug is softer because of the tabby pick between every other rag weft pick I like to cut my fabric strips with the warp grain of the fabric the fabric will cup nice in the shed the fabric cut weft grain has a bit more give to it and it does not cup well in the shed The rug is as strong as the number of warps to the inch I myself will not sett 8/4 warp less them 10 to the inch 12 is what weavers have used for a lot of years and I set for pattern weaving no less then 15 to the inch I find a rug with less then 10 warps to the inch to soft I like a nice tight ferm rug Joe

jordanj (not verified)

I am not the expert, but your mercerized cotton should not cause sticking. Can you post a picture so we can see what's happening? Perhaps a finer material for the string heddle?  I use 8/2 mercerized cotton for mine.

Jennifer

 

Caroline (not verified)

hi Cheryl, try putting hair conditioner on your hands and running your fingers through the warp. Once it dries, it will coat the warp, and make it slightly stiff, which is much easier to handle as it will no longer grab. If the hair conditioner is too thick, you can dilute it as much as 50/50. This works wonderfully on wool and other grabby, sticky yarns. You are basically using the hair conditioner as a warp size, and it rinses out once you have completed your item, leaving the weaving nice and soft and nice-smelling.

cheriberi (not verified)

Ok, I tried to reply and obviously I have no clue what I'm doing!!! I can't find my reply. So, I'll try again and hope I don't end up with two!

My string heddles are about 1-3/4". Is that too short? What height should it be instead? I can open the shed rod shed without a problem, but when I try to scoot it down past the heddle shed, everything is just plain stuck! Here's a photo.

 

Thanks!

Cheryl

cheriberi (not verified)

Yea! I'm so excited! I very carefully reinserted the lease sticks and made sure nothing was crossed, then redid the heddle shed.... held my breath, and...I was able to create the second shed and bring it in front of the heddle loops!

Thank you for your help! We are going on vacation next week and I think this is going to be a great way to bring something to weave with me without taking up much room in the luggage!

Cheryl

Caroline (not verified)

Hi Vicki, sorry its taken so long to answer, but I've only just found your question.

You say the warp threads on the edge have collapsed down - did you use paper, venetian blind slats, or some other spacer inbetween your layers of warp when you wound it onto the back beam? This prevents the warp collapsing in on itself and helps maintain an even tension.

Doubled selvedges can help, but will not make any difference if the warp is not wound on evenly in the first place.

You can even the tension up by hanging weights on the offending warp threads at the back of the loom just before where it goes around the beam. Small containers of nuts and bolts are ideal as you can adjust the weight. I use fishing weights. Anything that you can fiddle with so that the edge warps are the same tension as the middle. As long as they are not tied on tightly, they will stay there as you move the warp forward.

Re-sleying the reed will not work unless the cloth is really very sleazy and loose. Remember that once you take your piece off the loom and wash it, the weave should tighten up a bit.

You don't say what kind of yarn you are using, but did you check whether 8 epi was the correct number of ends for an even weave using your yarn? Wind some of your warp yarn around a ruler, making sure you do not pull it tight, and that each wrap is snug up against its neighbour without overlapping. Do a couple of inches, then count how many wraps you have around 1 inch. Halve that number, and that should give you how many ends per inch you need to sley the yarn for a balanced plain weave.

Are you working from a weaving book? Deborah Chandlers' Learning to Weave is a good place to start and should be in your local library. Its also available on Amazon if you wish to purchase it, and should give you a good start in the craft as she covers the basics thoroughly.

If you can find local classes, or a weaver who can help you, seeing is worth a thousand words, so joining your local Guild is a good move, too.

Hope this helps,

Caroline

Vicki Allen (not verified)

Thanks, all. Your suggestions are appreciated. I have the Deborah Chandler book and it is my mainstay. I have a roll of butcher paper attached to my loom that feeds  in as I wind the warp to keep the threads separated so that wasn't the problem.

I meant to tell you that I am using Sugar and Cream cotton yarn. I really believe that is most of my problem. I did not get the tension tight enough as I wound onto the back beam. I am used to weaving with wool or acrylic yarns.

I did, however, reslay to 10 epi. The cloth is not so sleazy now and the selvedges look neat. I am also beating on a closed shed between treadle changes and that is keeping the edges from drawing in. This is a sample project and I may find the 10 epi is too stiff after washing, but we'll see. If so I will try the 8 epi again but with more care when winding on so the tension is tighter to start with.

I will post a picture soon. Thanks for your ideas.

Vicki Allen

Vicki Allen (not verified)

I wove off one placemat and took it off the loom, keeping the on-loom warp tension using a lease stick capture technique of Peggy Osterkamp.

At the 10 epi sett the mat looks good. It measured 17 x 12 off the loom. I washed and dried it and it is now 15 x 10.5.  So that is the amount of shrinkage.

I found that the sage Sugar and Cream, which was on a ball, is stretchier than the ecru Sugar and Cream that came on a cone. This resulted in part of my tension problems since my warp is sage and ecru striped with 8 ends per stripe.

Since they stretched differently, I have a ripple effect scattered over the placemat where the sage apparently relaxed after I took it off the loom and possibly drew up more in the washing/drying process. This makes what looks like eight pick diagonal ecru dashes in random places.

Is this what is meant by tracking?

I'm going to post a picture as soon as I can.

Meanwhile I'm going to weave off the rest of the warp and enjoy this learning experience. The placemat is soft but stiff enough to use.

This is what makes weaving so much fun: there is always something new to learn! Thanks for your ideas, and comments. It is great to be able to consult this group!

Vicki Allen