onafixedincome (not verified)

Yes, please--that would be really helpful.  Franco had suggested laying stiff paper between the wraps of the warp, which has helped considerably, but boy! are the heddles and shed being a major pain!  The warp is, BTW, two-ply unmercerized cotton and it is shedding worse than my dog....

I'm close to just ditching the whole thing in disgust, really... :(

Ruthie99us (not verified)

Wah! I had left my backstrap on the floor, never thinking for a moment that the dog might be interested in it. When I came back, the bone was across the room with the tip missing! This wonderful link was on "Handweaving Today" today, about a man in Peru spinning and weaving with trash! IT's really great: http://www.youtube.com/watch?v=NO5VBiM5W_I Laverne! It was so great to meet you in Albuquerque. Thank you so much for helping me with my warp... I've got to find a substiute now for my Llama bone, it really was working great. Ruth

onafixedincome (not verified)

Yep, the very first project was the mercerized perle cotton and it went really pretty well.  Guess it got me jumping too far ahead. :(

Been doing some reading--suspect that part of the problem is that my heddles are short? and thinking I may make a second heddle stick just to have better control of the shed....??

Becoming disenchanted....

francorios (not verified)

If I understand correctly your shed is not opening very wide.

If your string heddles are not about 3 fingers high or as wide as your sword/beater, it will limit the size of your shed, because the lower warp will pull the string heddles down between the strands of the upper warp. BTW, a loose warp string will not be able to pull down the string heddle in this step, so be sure all the strings are tight.

Use your beater stick/sword to hold the shed open. First turn your shed stick behind the heddle to open the shed. Then push the beater/sword into the shed in front of the string heddle. Then turn the sword/beater to hold the shed open for the shuttle.

At this point look closely at the warp to be sure you have not dropped a warp string. When satisfactory, push your shuttle through. Use the sword/beater to beat the weft.

I hope that helps.

Have a joyful day!

Caroline (not verified)

Does the broken peg go all the way through to the other side of the loom? Not that it really matters, but its simpler if it does. You could  find a wood drill bit of the same size as the dowel and carefully drill it out. Then all you have to do is glue in the new piece of dowel and sand it down.

Cordless drills tend to be lighter and easier to use than regular electric drills.

whiteoakgrandmother (not verified)

I would use a drill bit that is a little smaller than the dowel. It's too easy to end up with the hole too big if you use the same size bit. Then I would carefully scrape away the remainder of the dowel and the glue then glue in the new dowel. Be very careful that your dowel is not the slightest bit too big for the hole or it may split the frame. If it's a tiny bit too loose, you can use a string or cord to make the fit tighter.

jeanne (not verified)

Poor inkle! Would it be possible to repair the broken peg? That would be the simplest approach, especially if the part that's still attached to the loom is still perpendicular to the loom frame and there's enough of it to glue to. You'd need a really strong glue like gorilla glue to restore the peg.

If you need to replace the peg, you can saw off the remaining peg and then drill it out, but you want to be careful to keep the drill hole straight. If you have a drill press (or can find someone who does), that will help. If your loom is an Ashford, you can remove the tensioning knob and the loom will lie flat, which will also help. I've used what's called a Forstner bit to install dowels, but I've never used one to drill out an existing dowel. That bit will give you an even cut, whereas a regular bit might tear at the wood, so use some wax on the bit and be careful! Also, you want to be sure to get a nice hardwood dowel that fits snugly and glue it in with a good strong glue. If it's wobbly or not perpendicular, you will have trouble with the warp.

It's good to have a woodworker on call for these things sometimes! I hope the surgery goes well and the little guy is back to its old self quickly!

newtoweaving (not verified)

Hi, Gail, I am assuming Fog is the wonderful dog in your picture?

Shelby is the name of our pup, in my portrait pic. We have had  her about 5 mos. I am interested in weaving dog collars for her and wonder if you have a certain book or resource you can recommend.

Thank you for any help you can give. Michael wrote me a post but I can't find it to respond; I am having a terrible time navigating this site. That sort of cracks me up!lol

mar

Weaverchick007 (not verified)

 

I have heard to avoid back strain, but seems like it would be easier to just adjust the bench.

What is the advantage of raising a loom?