djfiberarts (not verified)

Thank you Joanne! I sent my info

DJ

djfiberarts (not verified)

Wow, thank you again. I want a temple now :) I'll have to wait till next month. Spent too much this month already, lol!

To all students...check out the Glimakra website. They have a "learning: looms and weaving" section that is very informative.

http://glimakrausa.com/learning.html

DJ

Caroline (not verified)

hi Jerry, This isn't fool proof, but failing anything else, cut 4 pieces of string or yarn the length you want your placemats to be. Fasten one end at the start of a mat, and weave up until you reach the end, leave at least 4 to six inches, even more depending on whether you want a fringe etc, (unless you are hemming as you go) and start the next mat, attaching a length of yarn to the start. Repeat for each mat.

Remember that once you take your piece off the loom its going to be shorter and narrower than it looks on the loom. you will also need to give your weaving a wash to finish it off. This will help the yarn you have used to relax, bloom, and move into its final position, and again, depending on the yarn you have used, you may notice more shrinkage. This is normal!

I would suggest that next time you have a piece of yarn or string the total length of your weaving - you can mark the mats on it, how much space to leave between them etc, and it just rolls up onto the front beam with your weaving. If you have the room, this could even be an extra warp thread that you don't use. There isn't much room to see what is going on with a RH loom, and this is better than marking the warp yarn that you are using. You will need to make sure that it winds on the same way as the weaving itself to keep things as accurate as possible.

crosstownshuttler (not verified)

Hi Jerry,

I use a piece of hem facing marked with the beginning and end of each place mat plus the space between them needed for fringe or a few separating picks. I pin it to the beginning of the first place mat and wind it onto the cloth beam with the weaving. You can use anything flat, thin and unstretchable such as adding machine tape. This technique also works for making the beginning and end of an item match or assuring where the placement of stripes and pattern fall over the length of an item.

I hope this helps.

Carie 

claudia (not verified)

Hi Jerry,

I use adding machine tape. Once, while in Costco, I found a bag of 50 for $5. so I bought it and give them to weaving friends who don't have any. I measure out a piece of adding machine tape the finished length of the project (scarf, mat, shawl) and pin it along the edge of the weaving as I go. Be sure you allow for shrinkage and for take-up which always occurs.  I often jot notes on the paper as I go so when I stop weaving I know where I am if I am treading a certain way or weaving stripes. For stripes I will measure and pre-mark the paper so I know where to stop and end.

Some people use a tape measure and pin it on the edges as they weave. Just as an example of the differences you find on and off the loom. I recently finished a turquoise shawl with a supplemental warp (it's here) and when it was on the loom it measured 86" under tension. Off the loom it was 79" and washed (wet finished) with hot water and the finished shawl was 77". I expected it to shrink to 75".  The width changed very little.

Good luck and happy weaving. We'd love to see pictures.

Claudia

macpac (not verified)

Thanks so much.  This all makes sense and helps me out alot

-Jerry

lkautio (not verified)

Jerry, be sure that if you use a marking ribbon/tape/string/paper that you are careful about having it wind in with the finished cloth. You may need to unpin it at the point where it enters the cloth beam so it does not build up and create tension problems. Use 3 pins and leapfrog them.  If it runs beside the finished cloth you won't need to unpin.  I often just put a small piece of fine colored yarn that sticks out the edge at the beginning and end of a smaller piece or every 18" on a long piece.  If you measure under tension, then when it is relaxed off the loom, and again after finishing you will get an idea of takeup and shrinkage.

Laurie Autio

naturalfibres (not verified)

to measure whatever I am weaving - rugs, placemats, towels - I use a tape measure which I pin to my weaving with two pins that I keep leap frogging as I advance the warp.

Make sure you note down how long to weave your placemats so that they will all be the same length.

Deloominknitiot (not verified)

I had the same problem when weaving 3 cowls on one warp.  As elementary as it sounds, I use a dressmakers tape or a marked length of yarn and use large paper clips to hold it on the edge to keep it on the top of the woven piece as I roll it...worked for me so I hope this helps.

claudia (not verified)

Hi Carie,

I remember reading that article and thinking it would be a great project to try. I have had the opportunity to see Bonnie Inouye's creations in person and they are stunning. The advancing twills are almost magical in their movement across the web. I say go for it. I have all four looms warped and weaving at the moment and will join you as soon as one opens up. Of course, I'd love to try the 4 harness version.

Claudia