caroleweaves (not verified)

I agree, it was a nice afternoon at a beautiful location.   Thank you Jane for setting it up for us.

 

lizziejane (not verified)

Hi, I have been having similar troubles with my Glimakra Julia eight shaft countermarche loom.  I posted on the Glimakra Julia forum but it was suggested I also post on this forum as well.

I have been using the tie up suggested in the article by Madelyn and have yet to finish tying up the treadles, I only got part sorted today with that.  I became confused because when I used a four shaft threading and tie up to make some scarves the loom was fine and I had a good shed.  However I put on a light string warp to make some little rugs using up some yarn out of my stash, some old rug yarn and find that the shed is so small I couldnt get the shuttle through and also some of the threads werent raising as high as others.  I too spent a long time adjusting shafts and lamms and then came across the article mentioned above.  I hope it will work as I am very fustrated with my loom at present. 

This is the first countermarche loom I have owned and the instructions that came with it were to say the least, limited.  I only got a basic tie up diagram and no written instructions.  Although I have been weaving for about six years I have only had table looms to date.

 

lizziejane (not verified)

Well, I have now finished the tie up sequence on my loom and it works!  Very well.  I didnt think it would but it has.  I feel I have learned an awful lot in this short space of time through doing this tie up and certainly it helps to get to know the countermarche system much better.  I think I was expecting to get a bigger shed before because on my Louet table loom there was a good sized shed, however as Joanne Hall pointed out above, you only need a slightly bigger shed than the height of the shuttle and this is true. 

 

 

Aunt Janet (not verified)

I am halfway through my first rag rug on my Glimakra Standard.  As I've said this is a new to me loom.  It had all of it's harnesses tied to the lower lams, so I set them in place as they were.  I tied up the uppers, did the tie ups on the treadles and got to weaving.  I am doing plain weave on two treadles, I threaded on four harnesses.

I'm weaving, but I can tell I need some fine tuning.  I may have to replace cords in order to do the fine tuning.  Many of the knots are frozen in place having been tied and stored for many years. 

So here is what is going on.  My shed is too small.  One of them is clean, but the other is off.  One of the treadles hits the floor when I step on it.  The harnesses don't hang level.  OK, all of that needs to be cleaned up, and I think I can do it, with the help of the video and books.  I may or may not have specific questions along the way for you experts.

You must wonder how the heck is she weaving with all that going on.  Well, I didn't say I was weaving with ease.  I'm setting the rags in by hand, no shuttle.  Slow and steady.  The tension is great.  The loom came with an appropriate sized temple, so I'm using that successfully.  The rags I'm using are not my favorite colors, just what I had.  I have enough warp on for at least two more rugs.  One will be my handspun yarns.  Of course I hope to have the loom all straightened out before I get to the next one.

I'll be glad to hear advice.

Janet

Aunt Janet (not verified)

Thanks, Joanne,

  I am not going to "get it" until I practice.  My loom has the horizontal CM, and yes, I'm using the old fashioned cords.  I'll probably replace them with texsolv eventually, but trying to use what I have at the moment.  I've cut and replaced a few cords with some of the cord that came with the loom.

   I get it that the shed doesn't need to be much bigger than the shuttle.  So my shed is probably wide enough, just barely. 

   Something I noticed that I don't know if it is a problem, or just the way it is.  The heddles seem to be moving all over the place.  Sometimes they cross each other at the top of the harness.  It doesn't seem to be effecting anything, so I'm assuming that is just the way it is. 

   I want to understand this machine before I go out to the monastery to teach the sisters how to use their loom. 

   Moving right along.

Aunt Janet

Aunt Janet (not verified)

OK, I'll do that.  I'm re-tieing a few cords this morning.  Looking better already.

Thanks,

Janet

Aunt Janet (not verified)

I'm all straightened out now!  I tied up the extra treadle which stablized the lams so they can't cross each other.  The sheds are now even.  I'm still weaving slowly on this rug.  I was lazy and didn't prepare my rag strips for continous weaving, and I'm just setting them in with my hands for the most part. 

The next rug along this warp will be much faster weaving, though might still take about the same length of time, since it will be finer weft.  I'll try to get a weft faced rug in that one. 

Wondering how to determine where to hang the beater.  There are three spots available.  Also wondering about bench height.  I keep finding myself standing at the loom.  I will try the highest adjustment on the seat and see if that helps.  I don't really mind standing at the loom, but will probably want to sit if I'm not fussing with rags.

Thanks again for the help, Joanne. 

Off to weave for an hour before work.

Janet

Aunt Janet (not verified)

The adjusted seat is great.  I'm such a shorty, I need to get way up there to get a good reach.  I have some felted fleece rugs that would work great for a seat cover.  I only had time to weave a few inches yesterday, but I should have some good weaving time this weekend.  I've been advancing the warp every two inches just because it feels right on this project.

Next project will use four shafts, then I'll think about using all 8.  Before this loom showed up I had declared that I never needed to weave on more than four shafts.  Of course there are plenty of four shaft projects for a lifetime, but I have now begun thinking beyond the four.

Janet

Aunt Janet (not verified)

Weaving right along.  Halfway through the second rug I realized that the rug was off square by half an inch as it went over the cloth beam.  Hmmm.  I checked all over the place and discovered one of the beater supports is in the wrong spot.  The support has a couple of bolts that I guess were loose on that side.  I didn't want to fix it in the middle of the rug, so I kept on weaving and finished that one.  Now I'll bolt down the support, even up the warp and weave my third and last rug on this warp.

I need to re-tie the treadles, oh boy!  I'm going to weave double cloth with greys on one side and colors on the other.   Nothing fancy, but i want to try out another tie up to get the feel of it.

Janet

Aunt Janet (not verified)

Thanks, Joanne.  I'll try to call parts by their real names.  Your book is great help.  I also love the video and the Big Book all that I purchased from your company.  Yes, I'm having a good time.  I'm 57 years old and kicking myself for not learning to weave when I was 17-27 or anytime earlier than now.  But, anyway it is still a lot of fun.  I'm so happy to be working on a good loom. 

I'm also having fun with the band loom. Thanks to Ed for getting it to me in time for my presentation at my guild this week.

Back to weaving.

Janet