weaver347 (not verified)

Just learned about this forum this morning and immediately joined.  I've been weaving rag rugs since 1986 and have not stopped since. 

My rug looms are two Union #36 and a 60" Varpapuu CM (12 harness).  I also have two four harness Nilus LeClerc's, a 36" and a 45", but they aren't as good for rugs.

I mainly weave with actual rags, which I wash, cut apart and sort for color.  I have a big electric cutter that has really saved my hands and shoulders, but I still sometimes use a regular rotary cutter and pad.

Had never thought of using a swift to keep the sewn weft from tangling.  Now it seems so obvious, thanks for a great tip Mary.

Dana, in northern Californa, where it is still foggy this afternoon.

claudia (not verified)

Hi Dana,

So glad you found us. We need lots of experienced weavers to help us newbies along.

Claudia, Co-founder Weavolution

juvondajones (not verified)

Where can I find Pendleton worms?

TinaHilton (not verified)

Maybe it's the warp width then.  It's a 60" loom, but the warp is only 12".  The yarn is 10/2 mercerized cotton so no lumps or bumps and I wound the pirns carefully like I always do.  The next warp is for baby blankets so will be considerably wider and will tell me if it's caused by the width of the warp.

And yes, it does go over the cord to fly shuttle.  I guess it must dangle over the shuttle race sometimes at just the right time when the shuttle is going across.

Thanks Laura!

TinaHilton (not verified)

Other than a short sample that I wove for this project, everything has been at least 20" wide.  I was pretty tired yesterday from doing a lot of weaving and my back was sore too, maybe because I was adding a supplemental metallic weft in the middle in spots,   It just made my weaving awkward and I think affected the way I was pulling on the cord.  But I finished it today and hope to get it wet finished tomorrow.  I am sooooooo glad I've finished this piece.  I've been nervous the entire time about making a mistake on it.  Hopefully I won't find any bad surprises after washing it.

Thanks for all your help!


TinaHilton (not verified)

I currently have a 40" warp on the loom and there have been no problems.  The warp keeps the cord off the shuttle race, so I think it's just a problem with narrower warps.

Bruce McLaughlin (not verified)

Is your warp "off centered" on the loom.  Narrow warps should be off centered 1/2 the length of the shuttle when using a flying shuttle.  If you are off centered to the right (facing the loom) the yarn should come out of the end feed shuttle facing you.  If off centered to the left the yarn should come out of end feed facing the reed.  More problems usually occur when off centered to the right because of the yarn being on the outside (facing the weaver) it's easier to be pulled off its track. 

Also, check to see if your loom is "squared" and the race is level.

 

 

TinaHilton (not verified)

I'm pretty sure this is it.  I had it off-centered, but only by one 2" section and it needs to be two sections I think.  I have to weave off a baby blanket warp, then try again with a towel warp I have partially wound on the sectional beam.  It won't be as narrow as the problem warp mentioned in this thread, but I remember having it happen a few times with towels too.

TinaHilton (not verified)

Yes.  I forgot that sometimes it would go over the cord too.  I think maybe I just gotta give up the fly shuttle for the narrow warps.  I can weave so much faster with it though -- except when I have to keep picking up the shuttle.

TinaHilton (not verified)

I know what you mean Laura.  When it works it's faster, when it doesn't I spend a lot of time picking up the shuttle and getting the yarn straightened out.  I do get more exercise that way, though ;-)