tien (not verified)

Have you considered removing the beams rather than leaning over them?  I always did that when I was weaving on my Baby Wolf (fondly remembered - that was my first loom!), and it made life a LOT easier.

And are you warping back to front or front to back?  I recommend B2F, because then you can use a trapeze to make your life easier when beaming on.  Laura Fry has info on warping with a trapeze (she calls it a "warping valet") on her website, http://www.laurafry.com .  It makes life a LOT easier - if I weren't beaming sectionally these days I'd use a trapeze for every warp.  Definitely worth looking into!

lkautio (not verified)

Sally Guy is a knowledgeable weaver (with a fun sense of humor).  She taught for years and may still be teaching.  Haven't seen her video, but it could be worth seeing if you learn well that way.  Look for Peggy Ostercamp's book on warping.  Lots of good pictures.  Or, get an experienced weaver to help you in person next time you put on a warp.

I like back to front also because it does not have to go through the heddles as you beam on (extra wear) or have to have the ends cut (tough to get them perfectly aligned when you tie on, and all those difference have to be worked through the entire length of the warp.  There are ways to minimize that problem with a choke tie and careful tieing, but it is just more work.  You also have a bit more loom waste.  That said, if you were careful, there is no reason you couldn't try rigging a trapeze somewhere in front of the reed if you wanted.  It would probably take more fiddling, but it would work.  I'd envision the warp going under the breast beam then over the trapeze for f2b.

Another good book with tons of tips and tricks is "Thrums" by Faith Nunnely.  It's like having a calm, experienced weaver with a sense of humor sitting beside you, feeding you good ideas for easier ways of doing things.  She has a picture of a simple trapeze in her book (first place I saw one).

Laurie Autio

weaversouth (not verified)

This isn't very helpful, but it's funny.

I had been putting a very dense warp on my Macomber and was in the habit if sort of draping myself over the breast beam (which will be seen to be rather ironic in a minute).  I reach with my left hand for the ends and pull through with my right.  It was right comfy!

A day or so later, I was getting dressed and caught myself in the bathroom mirror and one of my "assets" was purple nearly all over.  PANIC ...call the dr, tell them I need to see him TODAY and I get myself over there, wondering if my will is in order, can I cope with a mastectomy etc.  While sitting in his waiting room I had time to think. It was on the left side..hmmmm.  By the time I got in there I told him "I either have a terminal disease or a truly amazing bruise."  Yep...every time I "reached" I was mashing away and, that tissue being quite sensitive I had given myself a massive hematoma.

NOW THAT IT IS OVER..it's pretty hilarious, but, when first seen, it was pretty terrifying.

Now I remove beams and make sure I am at right heights, etc.

Look after your assets (-'

On a more helpful note.  I thread f2b now, having used the other method for years.  I find it far more efficient. I have NO tension issues (to my great surprise)  and far fewer abrasion problems (I know that sounds odd, but I don't).  Granted, with sectional beaming, I'm back to the b2f method, but I really like doing f2b.   I do like to use a "roomy" reed when I can, as in, using a 6 reed sleyed 2/dent for 12 epi etc.   If you worry about abrasion, this is a great trick.

Nancy C/

weaverbird53 (not verified)

I have an 8-shaft Baby Wolf, too. I warp f2b, and for threading I use a low stool that puts me nearly eye-level with the heddles when the loom is unfolded (i.e. in weaving position). That way I can get right up against the back beam, with the heddles in easy reach even with my back almost straight.  Threading and knotting onto the rod goes quickly and no sore back!

Good luck finding a method that works for you. There's often a period of trial and error, but you'll soon discover the best way to go about it, I'm sure.

Happy weaving,
G

hlf (not verified)

OK, that's awful and absolutely hilarious (to have happened to someone else!)  :-)

Thank you for sharing the story; I shall hold it to my chest carefully.  Very, very carefully. 

 

-heather f.

hlf (not verified)

I think that's what it's going to boil down to - a shorter chair/stool, and practice!  My spinning stool is still too high, and the weaving bench is WAY too high for dressing the loom.

Thanks!

-heather f.

hlf (not verified)

Hrm.  Didn't actually know I could do that.  I'll have to look that up!  I do F2B.  I can't logically wrap my brain around B2F.  It sounds like putting on pants before underwear to me.  :-)

 

-hf

Belinda (not verified)

Is there a book specific to the baby wolf? Purchased an 8 shaft in hope it would be kinder on my aging body and I would be able to weave outside in the summer. Seem to have many questions. My other loom is an old Canadian counterbalance and it seems to be more forgiving. Just wondering. Thanks , Belinda

claudia (not verified)

The best method, teacher and video I have found is the one by Tom Knisely of The Mannings. His video covers it all from beginning to end, very efficiently and the warping method he teaches and has used for years is a variation of f2b. I don't use it every time I warp my baby wolf but it is the method I use when I want it done quickly and easily. I can't find it on the web but you can call or email The Mannings.

I wrote the Mannings and learned they still have the video available for $44.95. Just call their toll free number or write to them as I did and you can order it. I believe it's worthwhile. Tom does a lovely job on all the basics, especially warping and threading the loom.

Claudia

Belinda (not verified)

Thank you so much Claudia. Appreciate you taking the time. Have been checking out ways to be more comfortable and make life easier. Will call today. Belinda