francorios (not verified)

Okay, I got it. That's similar to something I did using a short section of coat hanger wire.

I might go ahead with an edge cord for the first piece.

Do the "traditional" weavers usually slide the piece off the loom bar and weave with a needle to finish the edge?

Have a good day!

francorios (not verified)

Laverne said: The start edge needs no work once off the loom. If they want fringe on the far end, they remove the loom bar and braid or knot the remaining unwoven warps. If they don't want fringe at all they weave to about half way, then turn the loom around and weave in from the other end.

------------------------------------

Let me re-phrase my question.

If I don't want fringe at all, when I remove the loom bar, what do I do to the remaining unwoven warps?

Do I replace with smaller loom bar and then finish with a needle?

Have a good day!

francorios (not verified)

I'm not asking the question right.

Let me start at the end.

 

This is a washcloth I wove on a frame loom. The bottom and top edge are where the loom bars would be. I want the start end and the finish end to look like this. How would I do this on a backstrap loom?

Thank you so much for your patience Laverne. I'm sure if I was in the same room you could point to it and make it totally clear.

Have a good day!

Franco Rios

francorios (not verified)

laverne wrote: B...an edge cord ,knitting needle or coat hanger piece has been passed through the warp loops at BOTH ends and this has been lashed to the loom bars.

---------------------------------

That's the confirmation I needed. I was wondering if the "traditional" backstrappers had a different way of doing it.

Thankyou-thankyou again for your patience and I love the drawing!!!

Have a joyful day!

Franco Rios

francorios (not verified)

Groovin'

- Did not get much work done on the backstrap loom today. Most of the tutorials online suggest putting a groove in the loom bars to help hold the ropes in position. One site says to cut a groove with a saw one inch from the end and use a chisel to cut a groove.

Since my goal is always to go with tools found inside the house, I decided not to use the chisel, which is outside in the garage. I could have done it with a sharp knife. But I used some rough sandpaper (60 grit) wrapped around a ruler to make a row of grooves around the dowels. And yes we keep sandpaper in the kitchen because we always seem to need it for one thing or another.

It was fairly easy to do, I did grooves on 4 dowels in under an hour while watching television. I marked a line one inch from the end, then sanded groove in sort of a V shape, but with more angle to the vee side near the end of the dowel. As you can see, our trusty wooden bar stool was the work bench for this job.

Have a good day!

Caroline (not verified)

A bastard file works just as well!

For the correctness police - its what Australian hardware stores call a particular kind of rasp.

My rasps and files live in my fruit bowl on the kitchen table, along with an assortment of pliers, snips, drill bits and drills, so they are always on hand! I may not know where a sewing needle is, but I always know where the tools are.

francorios (not verified)

Caroline wrote: My rasps and files live in my fruit bowl on the kitchen table, along with an assortment of pliers, snips, drill bits and drills, so they are always on hand! I may not know where a sewing needle is, but I always know where the tools are.

------------------------------------

If you get a florist frog or some foam you could probably make a nice tool arrangement as a table centerpiece.

Have a good day!

esmecat (not verified)

i am definitly going to have to try this soon.... but i will have to make a string heddle to do it, since it would be impossible to remove the rigid heddle after weaving...

esmecat (not verified)

 

since this was my first piece of weaving, i don't have any secrets to share, lol. i left a fair bit of fringe on each end of my weaving... i am loving the information on ways to work with more selvedges! i am going to be giving it a try as soon as i get some free time!

i am preping for a retreat (leaving tomorrow) and haven't had time to sit down and cut/sew it. (not to mention, a fair does of fear about design decisions...) when i get back, i'll work on turning my first cloth into a bag for the loom and post pictures... i promise! in the mean time, here's the fabric off the loom:

and i blogged about it here:

http://www.jenminnis.com/artblog/?p=240

 

francorios (not verified)

Ideas for making the backstrap include some that have been mentioned on this thread already.

- Cut off legs from a pair of jeans for improvised backstrap. I thought about that one because I save old jeans for the purpose of rag strips for making rag rugs. You can also convert the "shorts" into a shoulder bag by sewing the bottoms/legs closed and using some fabric of the legs for sewing the shoulder strap.

- Take a dishtowel, tie a knot in opposite corners so you can attach a rope. You can also take an old terry cloth bath towel and do the same thing. You might have to rip it in half to reduce the bulk.

- A pillow case can be used with knots in the corners.

- In the Curious Weaver Journal #2 article they suggest using a length of rope around your body as a strap while you weave yourself a strap as a first project. You may want to pad that rope with a towel or something.

- I have a leather belt that is too small for me (it shrunk! I swear it shrunk!) but if I put loops on each end it should work as a backstrap. I also figure a regular belt can be used without anymodification at all. I'll try to take pictures of that idea soon.

- Old sheets can be ripped down to a wide sash sized strip, a knot in the ends, attach a rope.

Just some ideas.

Have a good day!