Hello;  I'm hoping someone will have an answer to this query.  How does one accurately calculate the correct heddle size for a loom.  Can someone advise me how to do this?  Thank-you in anticipation of your help.

Comments

Michael White

I am not certain were you are going with this question so I will give you two answers. On a counterbalance/march loom the warp yarn goes through the center of the reed, on a jack loom the yarp yarn sits on the bottom of the reed/beater. Keeping this in mind you will have to adjust the eye of the heddle to meet the above needs. The size of the heddle "eye" is determented by the size of your yarn. If you are weaving with "mop" cotton your "eye" would have to be much larger then if you where using 120/2 silk. Hope this helps. 

Michael

Joanne Hall

You won't have a choice of heddle size if your shafts have sides.  If they do not have sides and there is plenty of space for the tie-up, then most floor looms have heddles from 9 1/2 inches to 11 inches.  Longer heddles can be found on computer operated looms and some looms that have shafts with sides.

Joanne

WEAVEblah (not verified)

Hi Michael;  thanks for your reply.  I've rephrased my question if that helps.  Your comments re: counterbalance/march/jack looms make sense.  It sounds like one needs to tie-up the lift system before one can take measurements to gauge the correct heddle size.  On a countermarch loom (with over-slung beater), for example, lamms would need to be horizontal, and the reed would be in place in the batten. Would shafts also need to be assembled (without heddles attached) and hanging in position?

WEAVEblah (not verified)

Thank-you Joanne.  The loom is constructed much like a GlimĂ„kra Ideal and has an over-slung beater, a counter-balance lift system (which can be converted to countermarch) and a weaving width of 100cm.  The owner wishes to replace the hand-made cotton heddles with Texsolv.  I have suggested installing 280/12 heddles, but I thought it might be useful to accurately gauge the correct size.  I've never had to calculate heddle size before, so I thought I might ask the experts how it is done.

Michael White

This changes my answer. Like Joanne say, since you have a frame (shaft). The size of the heddle would be from the top of the heddle bar to the underside of the bottom bar. You would then adjust the location of the heddle eye by adjusting the frames.

Michael

Joanne Hall

Yes, the 280/12 size is correct.  To determine how many to purchase, decide the highest sett you would use for the 39 inches.  If you might go to 20 epi for the full width, you would need 800 heddles.  They are $17. per 100 if that makes any difference in your decision.

Joanne

kerstinfroberg

I have been pondering your question - don't know the right answer (except I suppose Joanne is right, esp if it is about getting ready-made heddles).

Approaching it from the theoretical angle - it has to be a balance of

the space between the shafts, the lamms (one or two sets) and the treadleshow big one wishes the shed to be (can only be half of the heddle length)how tall the reed is (impossible to get a shed bigger than the reed will take)

As the warp line is fixed, we already know where the heddle eye goes. Using simple figures - say that the heddle is 30 cm. This means the shaft/lamm/treadle will move max 15 cm up/down - except that the lamms usually have a pivot at one end. This means that the end of the lamm will move more...

As this is purely a theoretical discussion, I'll stop here, for several reasons. Like: on my old "homemade" CM, the lamms need to pass each other, which they usually do without problems. Therefore the point is moot?  When I first tried that loom, it had a curious CM with one set of horizontal jacks (the top ones, they are called jacks?), which meant the whole warp moved sideways slightly when a treadle was lowered. The whole thing was a nightmare to balance... The loom came with two different lengths of heddles, and I had put on (sort of a random choice) the longer ones. When I tried the shorter (a difference of maybe 2-3 cm), everything worked better. The heddles were hand-tied.

I gave up, got a modern CM with vertical jacks and texsolv heddles and have never looked back. - if I want to use all treadles (there are 20), I need to use a smaller shed, or he treadles will interfere with the lower lamms... These are the times I wish I knew how to do these calculations properly. :-)

Here is a picture of that loom in it's current incarnation (top pic). I think it has 12 shafts/treadles mounted. I don't have a picture of the first CM, but here is a scan from Cyrus: Manual of Swedish handweaving:

And.. had I not found that picture, it would have taken me a lot longer time to assembel/weave on it...

Joanne Hall

Hi Kerstin,

I have read about the sideways movement of this type of countermarch.  Believe it or not, a beginning weaver acquired one of these here in the US and it was hard to explain to a beginner what he had and what the disadvantages were.

The other complication with countermarch here, which affects the size of heddles and the measurements is that on the very old looms with horizontal countermarch, the lower lamms are not heavy enough to hold the shafts up.  Toika looms are still made this way.  When the shafts fall, there is even less space for the moving parts.

Joanne

kerstinfroberg

Joanne, I see what you mean, but I don't quite agree.

Mine also tend to sag some. If I come to the loom, and the shafts hang too low, I step on "all" the treadles at once. This will lift the shafts, and once I am weaving (one treadle at at time), I have not experienced any problems. I admit I have not tried to start from a sagging position - that might, perhaps, cause some ends to ... I don't really know what, but anyway, I like the warp to sit right before the firts treadling. And *if* I have a warp (threading/tieup, I should say) that sags, I put in the pin when leaving for the day. I have never tied "extra" treadles

What I did when I was still at the odd CM was to get the biggest nuts I could find at the hardware store and hang them at the outer end of the long lamms. (After that, I became addicted to big nuts, they are useful for so many tasks!)

Joanne Hall

I visited a damask weaver in Sweden who always tied up an extra treadle to all the lower lamms to give them just a little more weight.  I have instructios for this in my countermarch book.  And I have done this on Toika looms, with additional weight on the treadle to keep the shafts from falling so much.  They actually fall a lot.

Joanne

WEAVEblah (not verified)

Thank-you Joanne, Kerstin and Michael for your comments.

Submitted by Anonymous (not verified) on