I doubt this is anything new, but I am hoping for some practicle suggestions on handling 10m warps (or about 11 yards for the non-metric-ers)?

 

I have been working with wool and find it difficult to manage a warp over 5 meters.  Other than the classic tangling troubles, which I am dealing with by keeping small bundles (10 ends or so) and I've started using sticks for the warp beam, which certainly does even the tension considerably, I would love to hear suggestions to make it more manageable.

 

I have been warping mainly from front to back, as I find the reed a great organising tool.  Of course, one does tend to fray the wool yarn a bit this way.  I hate to think what will happen with mohair!  Is beaming first at the back, then working foreward really better?

 

Thanks for any suggestions.

 

Jamie

Comments

Dena (not verified)

Jamie-The whole front to back vs back to front issue can be a can of worms (I expect you will see that soon by opening up this thread).  My personal take on it is that both methods are good if you are proficient with them and either can be a mess if you're not.  Personally, I am a front to backer and my warps tend to be around 30 yds long.  I like using heavy kraft paper (70 lb) to pack my warps because it is less fuss than the sticks.  I think ten ends in a bundle is very small.  My general rule of thumb is 8-12".  The most important thing is that you put a REALLY tight tie about 18" from your cross (or 36" from the beginning of your warp).  Then, when you are threading your heddles, give a gentle pull (not hard enough to pull it out of the knot) on each thread individually so that it pulls in a straight line out to your tie.  That organizes your threads so when you tie on they are all exactly the same length so that beaming is much, much easier.

The thing I love the most about front to back is that every thread is exactly where you want it to be for the entire warp.  While it is a bit more time beaming, it appeals to my OCD (we all are, really).

I use the reed as my "warning device".  When something unpleasant comes to the reed, the reed will move front the front position to the back position while beaming and you know it's time to clean out the warp.  I know that there are plenty of weavers who don't agree, but while I don't wind under tension, when I am organizing my threads in the front of the loom, I hold the threads under tension while I move my "knots" down the length of the warp.  Remember as you are cleaning out your warp that the action is to get all the threads the same length, not to "get the knots out".  It's a different hand movement.

Dena (not verified)

Jamie-The whole front to back vs back to front issue can be a can of worms (I expect you will see that soon by opening up this thread).  My personal take on it is that both methods are good if you are proficient with them and either can be a mess if you're not.  Personally, I am a front to backer and my warps tend to be around 30 yds long.  I like using heavy kraft paper (70 lb) to pack my warps because it is less fuss than the sticks.  I think ten ends in a bundle is very small.  My general rule of thumb is 8-12".  The most important thing is that you put a REALLY tight tie about 18" from your cross (or 36" from the beginning of your warp).  Then, when you are threading your heddles, give a gentle pull (not hard enough to pull it out of the knot) on each thread individually so that it pulls in a straight line out to your tie.  That organizes your threads so when you tie on they are all exactly the same length so that beaming is much, much easier.

The thing I love the most about front to back is that every thread is exactly where you want it to be for the entire warp.  While it is a bit more time beaming, it appeals to my OCD (we all are, really).

I use the reed as my "warning device".  When something unpleasant comes to the reed, the reed will move front the front position to the back position while beaming and you know it's time to clean out the warp.  I know that there are plenty of weavers who don't agree, but while I don't wind under tension, when I am organizing my threads in the front of the loom, I hold the threads under tension while I move my "knots" down the length of the warp.  Remember as you are cleaning out your warp that the action is to get all the threads the same length, not to "get the knots out".  It's a different hand movement.

sandra.eberhar…

I am generally of the back to front camp, and I usually use warps 25-40 yards. I use a lot of 2/18 wool. I keep the warp under tension and use a roller that I mount above the loom as a trapeze or valet.  I think the very small bundles might be part of your problems.  I find that larger bundles tend to stick together and not to tangle.   Although many people use lots of choke ties, I don't.  I  use choke ties  at the beginning and end, and in the middle if the warp is slick.  I think I handle the warp very little, being careful not to dislodge threads when I chain it.  I also apply no tension to the warp with my fingers when I reel it.  I rely on the hooks in the cone stand to supply tension, which means that the tension is always even.

Sara von Tresckow

When starting out, you need a good insurance policy, so to speak, when warping. By all means chain your warp with care - make 2 crosses, if possible. (It has happened more than once that one was messed up and all I needed to do was turn it around and start over). Choke ties, in the beginning keep things nicely together - you need this until you are comfortable with warping. Ideal warp chain size is enough threads for 6-10" weaving width - not too small, not too large. Direction? In every country but the US(ans perhaps Canada), warping is done by winding that warp under even tension on the beam before cutting the loops and threading anything. The most successful way to warp this way is to place your raddle (or coarsely sleyed reed) BEFORE the lease sticks and the warp beam. This way, the bundles for an inch or so separate, then they slide over the sticks, and then wind on the beam. Use your preferred method of packing - the sticks you use now will be excellent.

DO NOT TAKE SHORTCUTS - you first need to learn the long cuts until you are secure in your warping.

Joanne Hall

Hi Jamie,

It is also helpful to wind the warp with 2 or 3 ends, making a lease cross which is 2/2 or 3/3.  Then if you keep the lease sticks in this cross as you beam the warp, you will avoid tangles.  With experience, you will not have tangles in your warp.  So, keep observing how your warping goes and it will get better each time.

Joanne

gartenweber

OK, I need to digest this, as some of the terms are unfamiliar to me.  Most of my references have been in German.

 

Is there a video with the knots?  I can't quite visualise this.

 

With my last warp (5m) I had measured it in large bundles and then seperated these into smaller bundles for the placement.  This may have exacerbated the situation by dislodging the placement after the cross.  I do not use lease sticks; they are cumbersome in my small room and I have dropped the warp into a nice knot while working with them.

 

Clearly, practice and self-analysis is key.  All your suggestions and experiences are truly appreciated.  This is the stuff you don't get out of a book in any language!

 

cheers,

Jamie

Erica J

I use both methods of Warping. Being proficient with your method is key. For video, I recommend Daryl Lancaster's Warping Front to Back class. Weavolution.com/classes

ReedGuy

gartenweber,

If you have sufficient yarn for each bout you make, the only knots will be at the start and the end binding the 2,3 or 4 ends your winding at a time. This will change if you come to a knot in the yarn or you run out before you complete a trip around the reel or board. Most will back up and tie the new knot at the turn peg, so there is no knot in the middle of a warp end. I have never had to need for two crosses, but it is added security.

For fine threads I put sectionals on my warp roller and use tension box and spool rack. My space is limited so this is one of the consequences of that.

I do not warp longer than 10 yards. I certainly could, but I like to go on to new things by the time 10 yards is woven. You may find this to be the case as well if your new to weaving. If you do overshot or doubleweave you will become aware. ;)

debmcclintock

The question in my mind is once you chain your warp are you tying it with a separate bit of yarn to keep the chain from slipping apart. Once you secure your warp chain you can move it around as needex without it coming apart. I've also given you a link to a raddle discussion. There is a photo with the raddle and lease sticks inplace that might give you a starting point for your work area. http://www.weavolution.com/group/diy-looms-tools/raddle-make-your-own-o… In my mind, no matter if warping from back to front or front to back a secured warp chain, lease sticks and a raddle are necessary basics. No question you can warp without them but I'm alot happier with them.

Sara von Tresckow

IF German is  your main language, try to get a copy of

Erika Arndt "Handbuch Weben"

Ursula Kircher "Am Webstuhl mit 4-schaeften"

or any other comprehensive book on weaving. You definitely will need to learn correct terminology and methodology - weaving on longer warps is not something that can be done haphazardly. Learning to weave is a series of "not yet, maybe next times".

Weaping 10 meters without using lease sticks is pure folly - they cannot hinder your process if you tie them together, and then to the loom where they are conveniently placed, so they cannot fall out - the cross, held in place by those sticks is the heart of the warping process. If that is not orderly, the warping process will be nothing but tangles.

sandra.eberhar…

My lease sticks used to flop around a lot and were a pain until I started connecting them with pipe cleaners to tie them together. No more floppy sticks.

Submitted by gartenweber on