I have figured on my first project that I need 288 E.P.I. and 872 yards. But on a 2 yard warping mill how do I figure how many times I need to go around the mill to have the correct amount of yarn for my project? 

Comments

lkautio (not verified)

It looks like you want to make a warp that is 3 yards long. 

Cut a guide string with knotted loops on the ends to go over a peg.  The finished length of the string (with the looped ends) should be the same as the length of the warp you want, in this case 3 yards. 

Wind it onto the reel as if you were doing a real pass of a warp thread, following the path of the cross.  Angle it so that it comes out evenly to a peg and/or adjust the end peg to hit at the end of the string.

Follow the guide string down and up when you warp.  It's easy and quite accurate.

Happy weaving,

Laurie Autio

 

TNWEAVE (not verified)

I am still confused, when you say 3 yards which would be 108", who many times do I go around the 2 yard warping mill to obtain the 3 yards. Example of the answer I am trying to understand, would I go 10 times around and bundle that 10 and do that 22 times to give me the amount of yarn to do the project? I guest where I am getting confused is a 2 yard mill should give you 2 yards after you go around it once and 3 yards would only be going around it 1 and half times, and I know that will not be near enough for the project. So I just trying to get it straight in my mind, and I am sure I have made it more complicated than it is. Once I understand the concept I think I will be ok. Here is my project, it might make it easier, to get me started on the correct path. 4 towels 16" wide X 22" L with 2" between each towel. I want to know how many times I need to go around my 2 yard warping mill to have enough to do all 4 towels on one warp. Hope that makes my question more specific. Thanks John Teague

claudia (not verified)

Hey John,

It's hard to explain without diagrams and there aren't many online.  Do you have any basic books like Deb Chandler's Learning to Weave?  I'll do my best here.  Do as Laurie says, measure a piece of yarn 3 yards long (allow for a loop at the top and bottom just as Laurie explained) in a color that is contrasting to your warp.  Now, put the first loop at the top of the warping reel and keep going around, it will go around one and a half times.  Every thread or end of your warp will need to be that long times the total number of ends.  So, when you use the weaving calculator in the Resources section here, you may find that your warp needs to have 170 ends or threads (I am basing this number on a sett of 10 ends per inch) and each end needs to be 3 yards long for your 4 towels to be 22" long once off the loom and finished. 

Going back to the warping reel, each thread will go around the reel one and one-half times, turn on the bottom peg and return to the top of the reel, that's 2 threads total; one each time to go around the reel.  You will need to keep a counting thread and make certain you put a cross in at the top or the bottom so the threads stay in order to make it easier to beam and thread them.

Is this your first project or just the first time on the warping reel?  Keep asking questions, we'll do our best to help you out.

Claudia

suzyhok (not verified)

 Hi John...

Are you talking about something that looks like this:You can see how the yarn is wound around and around the mill one thread at a time.  Sometimes you can use a warping paddle to wind more than one yarn at a time. Here's what a paddle looks like:

These items are from the Schacht website.

I tried to find a YouTube Video to show you how its done, but couldn't find a good one.  

Good luck.  

:-) Suzy

lkautio (not verified)

Is 16" your finished width or width in the reed?  I'm asking because 288 ends divided by 16 inches wide gives 18 epi.  That's certainly a viable sett, but one less commonly used by beginners.  It suggests to me that you are using something about the size of 5/2 cotton in plain weave or simple twill.  And, is 22" your finished length or length on the loom? 

I'm going to run some calculations for you based on *finished* lengths of 16x22":

4x(22" long + 2" divider)x1.10 (for 10% shrinkage and takeup) + 36" (for loom waste) = 141.6" = approx 4 yard long warp.

16" final width /0.9 (shrinkage and takeup) = 17.8" wide in reed

Sett = 17.8" in reed / 288 ends = 16 epi (good plain weave sett for 5/2 cotton)

288 warp ends x4 yards each = 1152 yards total

After you make the guide thread (as above) - which looks like it should be 4 yards, not two, each warp thread is one pass down OR one pass up along the path of the guide thread.  Use a counting thread or raddle cross and a threading cross.  So, you will be making 144 round trips along the guide string with your 288 threads.

Laurie Autio

TNWEAVE (not verified)

Thanks Laurie, I think from your explanation it is clear to me now and I have started. This is my first project on my own and I expect some confusion during this initial project. I am using 8/2 cotton witth a 12 dent reed. I believe I should slay the reed 211211211211 for my 16epi. May post future problems, so keep watching the threads. Once again thanks. John Teague

lkautio (not verified)

John, with 8/2 cotton the sett of 18 epi (2,1 in a 12 dpi reed) may be better.  A sley of 2,1,1 in a 12 dpi reed will give you 16 epi.

The more accurately you can follow the guide thread, the less tension problems you will have.

Laurie Autio

Submitted by Anonymous (not verified) on