Claudia Segal (not verified)

How lovely!  Your colors are great and I'm glad you posted a photo of yourself weaving.  

Claudia

Caroline (not verified)

I use warping posts, and have done a 15 metre warp on them - once. They are basically like the 2 side pieces of the warping board, and I clamp them onto a table, or the ironing board, or whatever is handy at the time. Yes, I found that with the wider distance it was harder to maintain a consistency in the tension, but I did it in small amounts at a time, took it slowly and carefully, and in the end I wasn't too far out in the length, just a matter of a couple of inches, which really surprised me! I probably won't do it again.

I think the key is towind the warp inch by inch, if necessary, and to take care as you go. If you try to warp up too much at a time, there is a very real chance that you could bend the pegs out of alignment.

My first board was one I used vertically, and anchoring it securely was the biggest problem. I didn't like it.

The beauty of my current system is that I can choose how long I want the warp to be by where I clamp it, and its so easy to store. Its basically two lengths of 3" x 6" with large dowels inserted into it every couple of inches. I have a 6 foot long kitchen table, which is how I can do a longer warp, but I also have a wooden tray that is 1 yard wide, so if I clamp it to either end I can get the shorter length in a very little space, sit down to do it, and not have to do much bending or moving around!

I'll be interested in what answers you get so I can improve my own set-up, though I find its perfect for my own modest needs.

3looms (not verified)

Have you thought about a warping mill?  I find a mill much easier on my arms and shoulders than a board.  They usually fold flat for storage, so they don't take up a lot of room.

But you asked about boards:  I have 2, a 14 yd LeClerc, and a smaller Schacht (about 5 yd capacity).  For me, the pegs on the smaller board are too close together & I hit my knuckles against them unless I'm very careful.  I attach the boards to a shelf in the studio with C-clamps so they don't take up extra wall space. 

 I think getting an nice even warp package is less about the tool you use to measure than about not crowding too much into one bout, no matter what tool you use.

Weaverchick007 (not verified)

I once read an article or a post where a guy put posts into the door frame of the door of his studio.  Just drilled large holes, and then glued the pegs in.  I bring this up as it is a frugal solution, and it would also give you some flexibility as to the number of pegs you want to work with.

Also, I attended Ruby Leslie's class at Convergence (GREAT class) and she warps with 2 warping boards at a time to get her extra long 20 yard warps.  She also recommends warping in a vertical path as opposed to a horizontal path, as it gives your arm more frequent "rests" when you wind on the lower pegs on your board, and it is easier to maintain tension of the warp.  Her warping boards are vertical, mounted on the wall.  She loves it, and there were a number of "ooohs" in the class and great interest in this technique.

Me I'm a warping mill grrrrrl.  I think it is the most efficient, winds the best tensioned warp (for me), and the most comfortable.  I ran into this old, decrepit, dried out warping mill at a guild sale for $5.  Brought it home, cleaned it up and gave it some love and it works great.  Rubs on the side (I call this the "brake"), and squeeks (I prefer to think of it as singing), and doesn't fold up, but it works great and I absolutely love it. 

Just some thoughts...

~D

 

Guiding Myth (not verified)

If you are looking for a warping board - I agree with Lara - vertical and horizontal pegs is easier on the body.  I would also recommend one that's about 1 yard or 1 meter wide to make it easier to measure your warp.

As for keeping even tension - 1.  You don't need any tension on the yarn at all.  Just let it pass over your hand without tension - don't hold it - just support it.  The tension produced by passing over your hand and exiting the cone is sufficient. 2. Warp quickly - if you wind the warp slowly (If you're like me) you will think too much about it and start putting in too much tension!  Most important - enjoy it!

Stephanie S

lkautio (not verified)

I agree with the suggestion to consider a warping reel/mill. I find they cut my time to about a third of using a warping board, and are far easier on the back. Mine folds to less space than my (now unused) warping board, and a fair woodworker in the family could easily put one together for you for the price of buying a warping board. See if you can try one before buying the board.

http://www.yarn.com/webs-weaving-spinning-weaving-tools-warping-warping…

Before I got the reel I used to put my board on a big chair at an angle and sit in front of it to wind. That seemed easier on the back.

Laurie Autio

whiteoakgrandmother (not verified)

The book "Spinning and Weaving With Wool" by Paula Simmons has plans for a horizontal reel. I haven't made one, but the plans look simple enough for my limited woodworking skills. It also folds up or disassembles for easier storage. Mine doesn't, so I often don't get it out of storage to use, and make do with pegs or something else for small warps, but the reel is definitely nicer to use.

TinaHilton (not verified)

I'm trying to get caught up on the Weavolution posts and this topic really caught my eye.  I'm getting a table loom to take with me in the motorhome when we go down to Florida this winter (hope to attend one of your workshops Laura!).  I'm trying to figure out how to wind warps, though.  My warping board is too big to take.  It looks like the pegs won't let me include a cross, if I understand how they work.  Any suggestions? 

suzyhok (not verified)

I used to have a vertical warping reel - a Harrisville - and loved it!  When I thought I wouldn't be able to weave due to rheumatoid arthritis I sold it.  I now am back to weaving - yahoo! (thanks to heavy duty meds.)  When I got my new-to-me Mighty Wolf it came with a warping board.  It is MUCH more tiresome to wind a warp with the warping board.  I've finally found that leaning it against the back of the loom at an angle, the top resting on the castle that holds the harnesses, and bottom resting on the back beam provides a comfortable angle.  I can sit on a regular chair to wind the warp.  But... I hope I can find another warping mill sometime soon!

:-)  Suzy

Thumper70 (not verified)

I use a rigid heddle loom - but have a set of warping pegs for those longer projects - and like you I prefer them not only for their space saving, but also because they're more flexible. I've considered a "proper" warping board - but space is an issue. I'd not previously thought of issues of tension etc - but for my part I'd think that I'd have more control using pegs.