kellytwo (not verified)

I'm back working on my sampler, and I agree with mmorse that sample # 6 and #7 aren't quite right.  In #6, thread 2 just floats along the back and never gets connected, and in #7, thread 1 floats the whole way. So after an inch of #6, I went on to sample 8 which is working okay. I hope to continue weaving more tomorrow.

Doreen

claudia (not verified)

What's a winkle loom?  Got any pictures?

I am still threading, had a few other distractions this week.  More on that in the Weavolution News tomorrow.

Claudia

mmorse (not verified)

Something that's true on my Kromski is that sometimes there are two sheds, an upper and a lower. Does the same thing happen on yours? Although I tried to be careful and consistent about using the wider one, it may be the wrong one. I need to get more scientific about figuring out which warps go with which heddle positions--I'm still using the "it's magic" approach and things often work out, but not with 6 and 7. More experimentation to come.

--mm

kellytwo (not verified)

On my Kromski, because I'm using the two heddle holders, I also have what appears to be 3 sheds because the holders are spread apart. If the heddles were held together like Susan suggested, I don't think you would have this problem, but I like to have my hands free, so I'm using the holders. If you're only raising one heddle you'll use the top shed because you've only raised one layer of warp, but if you raise, say shaft 1 and 2, then you would use the bottom shed because you've raised two layers of warp and you have to get under the two, and that leaves layer 3 unused on the bottom.  It's kind of hard to understand without being shown.  If you still don't understand, I can draw a diagram.  Let me know.

Doreen

mmorse (not verified)

Hello, Doreen,

That's clear. I'm still not getting 6 and 7, and by your description, the long floats on the back and general padded appearance may be the result of using what in other circumstances seems to work as shaft 3 (both down). I'll do some more testing. To add some additional challenge, I re-warped with my own handspun (spinning my way through a fleece toward a large project and I wanted to see how it would look), which sticks together a bit. The twill is more uniform with tamer wool (I need more practice spinning).

--mm

kellytwo (not verified)

Thanks Susan, I still have to do sample 10 before I start these last two. I really like sample 9, it's my favorite so far. I haven't looked at the under side yet, but the draft makes it look like both sides will be the same, which is the type of pattern I was looking for. If I use it for a scarf, I want both sides to be the same.

If you look at the sample 6 draft, the shaft 2 thread never gets picked up, so it just floats along under the bottom. The same with the draft for sample 7, the shaft 1 thread never gets touched.

Doreen

 

 

 

 

 

claudia (not verified)

Hi Susan,

I just dropped in while on vacation, to say you are doing a great job and, although I cannot join this WAL, I am using your drafts to weave along on my new to me Glimakra while I get used to the countermarche system of weaving.  You have inspired me to return to some of the basics of weaving with 3 and 4 shafts.

I do have my Harp with me now and have been working on a quick tencel scarf I want to finish before our next show on 6/5.  I needed something quick so opted to let color do the work and am doing plain weave with a hand dyed Just Our Yarn 5/2 tencel weft and a plain yellow/gold warp.   It's fun watching the weft colors develop as I weave.  I will post the project when we get home tomorrow.

Thanks for your hard work and the inspiration you have provided beyond our WAL.

Claudia

claudia (not verified)

How goes the WAL?  Does anyone have pictues to share?  Has anyone finished all the patterns Susan provided? 

Claudia

kellytwo (not verified)

I still have 3 more samples to weave. I'll take pictures as soon as it's off the loom.

Doreen

Jean9 (not verified)

Hi

Very late joining this WAL but have enjoyed reading the posts. I will be doing the patterns as soon as my loom is free. I was just wondering if all the treading possibilties are posted somewhere?

IE:

shed 1 - Heddle 1 up, heddle 2 neutral.

Shed 1 and 3 Heddle 1 up, Heddle 2 down. (no idea if that is correct just using it as an example).

I have used 2 heddles for double dpi weaving but have yet to try any patterns.