jordanj (not verified)

 As I have had to rethread my warp several times now, i have had an opportunity to try out various ways of warping/threading. I have a Flip and I think the easiest for me is winding the warp on the warping board, thread heddle two while it is in the neutral slot (and I am sitting at the side), move Heddle to the rear position, then put heddle on in the neutral slot and thread it while sitting facing the loom. I got quite the rhythm in my head. Slot, Slot; Slot, Hole; Hole, Slot. :-)

I have finished the first two samples and agree with Kellytwo that the 2nd was "nicer" than the first.

Looking forward to working on #3 tomorrow.

Jennifer

sally t. (not verified)

I have a question that is even confusing to ask.  So here goes.  I would usually raise heddle 1 for a shed. Or raise heddle 2.  Or lower heddles 1 and 2 (which would be my #3)  so on this last draft I think I need to be doing 1 and 3 at the same time.  Is that correct? Does that mean that I raise heddle 1 and lower heddle 2 to get that shed?  Hope this makes sense.  I have the book you used for inspiration, but he uses 3 heddles. I have a Schact Flip and 3 heddles seems impossible.  I can't  tell you how much I personally appreciate all the effort your posts must take.  I study them religiously.  I am somewhat of a closet weaver and they are so amazingly helpful.  Thanks Thanks Thanks! 

kellytwo (not verified)

On my Kromski 24" Harp, I am getting a good shed with using the two heddle blocks. But it's too much of a hassle to push them both down for shaft 3, so I'm using a pick up stick instead. I understand that it would work better by having both heddles in front of the first block, but I didn't like them hanging on the warp, so using a pick up stick for shaft 3 is working great. I haven't started the next sample yet, but I hope to have time to weave tomorrow. I'll post pictures when I'm done;

Doreen

amelia (not verified)

I am following along vicariously as my looms are busy with a variety of simple plain weave scarves at the moment.  I've woven a fair bit with 2 heddles on the Emilia, which has nice sheds; but as I get to the end of the warp, regardless of how many heddles I'm using, the shed shrinks, due to the shortness of the remaining warp. On the last one, I switched from boat to stick shuttles for a narrower profile of of the weft package passing through the warp. Your mention of David McKinney's methods reminded me ... next time, I will try his method of opening the shed and inserting a weaving sword (a fairly wide pick-up stick) and turn it on its side to make the shed generous enough for my boat shuttles to still pass comfortably through.

Thanks for that!

mmorse (not verified)

Hello,

Thanks for the clear warping instructions (I love your hand-drawn pictures) and for the time you're taking to put this together. It's fun! I, too, have been puzzled by the 1-3 combination. My Kromski gives very good sheds for 1, 2, and 3 sitting in the blocks, rather than any of them hanging. (yes, pushing them both down is a bit of a pain, but there it is). From your description of how to get 1 and 3, I'm wondering whether 1 (the forward heddle) in neutral and 2 (the back) down would do it. I'll try when I get home from work this evening.

--mm

 

Tuesday morning: Yes, that works. 1 (front) in neutral and 2 (back) down gives the 1-3 combination, and 2 neutral, 1 down gives the 2-3 combination. Exciting to see weft floats change to warp floats.

jordanj (not verified)

 I'm sorry, but I have had to drop out of this WAL. My choice of thread/sett was just not working. I was using 5/2 perle cotton with two 12 dent heddles and it was just too "sleezy". I think Claudia had predicted this! 

Since I have the warp on the loom, I didn't want to waste the thread and so I removed the heddles and recreated the cross and am now practicing my warp faced weaving techniques.

Thank you so much for organizing this WAL - all the work you have put into it is appreciated!  learned a lot and hopefully someone else will learn from my mistake!

Jennifer

mmorse (not verified)

Yes, I actually got them both to work. Pictures eventually. For what it's worth, I started with Dale Baby Ull, using 10-dent heddles. My warp and weft were too close in color, yellow and spring green, so I switched the weft to a charcoal sock yarn. Not nearly as pretty, but it's much easier to see what's going on.  I stopped the diamond twill after about 3 feet and rethreaded. For either, this yarn and dent combination produce a nice, fairly dense fabric.

I still have a lot to learn about e.p.i., draw-in, and the like. My sampler is about 3 inches wide, though I used about 50 ends, which would normally be somewhere approaching 5 inches. Would it be reasonable to guess about a third more ends to get the same width using this threading, given that you've got 3 ends for each pair of slots and holes?

--mlm

kellytwo (not verified)

Hi Jennifer,  I'm surprised that your 5/2 perle cotton wasn't working with two 12 dent heddles. I just took a workshop with Jennifer Moore, and we used 5/2 perle cotton set at 16 epi, and it was perfect.  I think (and I may be wrong because this is new to me too) that using two 12 dent heddles and a twill pattern should be giving you 18 epi. That would be even a tighter weave than what we used in out workshop.

I'm using 3/2 cotton with two 8 dent heddles, which I was afraid would be too tight, but it's just fine.

I haven't been able to weave this week, but I'll get back to the WAL soon.

Doreen

mmorse (not verified)

Thanks for the explanation!

Just a quick note. I couldn't get the first two of the latest ones to work--bunched up threads on the front and long floats on the back--kind of interesting for a padded effect, but not what was supposed to happen, I think. The third one, though, worked. I'm out of warp, and I'll try again when I've put more on.

--mm

klhow74 (not verified)

Hi.  I am late joining in this WAL but better late than never right?  So just to make things quicker I warped only 5" wide and it's weaving up about 4" wide so I will have about 4x4 swatches of each fabric, which is fine by me.  The threading chart was very easy to follow.  So far I've only completed the first 3 drafts.  For the plain weave I decided to just put 3/4" of it between each draft and have one continuous sampler because I think my warp will only yield about 60 usable inches.  We'll see.  This is fun so far and not really hard.  It's funny because when I bought my loom (just 2 weeks ago) the lady at the store told me, "Now all you will be able to do is plain weave on this loom." 

Here is a picture of the progress not that it is much to see but I noticed no one has posted any progress pictures so I thought I could encourage people to do so by being the first.  I'm just using size 3 crochet thread because I have no intentions of this being anything other than a sampler.