francorios (not verified)

So you had your loom warped at 12 epi.

Take a ruler and measure how many weft per inch in your weaving. It should tell you how many more weft you have in your fabric.

I know I was surprised find that my plainweave is not very balanced. I am reading Mary Black's New Key to Weaving and she writes that 50/50 balanced weave (equal warp epi and weft epi) is difficult to master.

That will be my next "apprentice" weaver goal.

Have a good day!

lkautio (not verified)

There is no problem with weaving bookmarks on a floor loom.  People do it often. 

If you are beating to a "feel" rather than beating to a number of ppi then a narrow piece will beat in much tighter than a wider piece (less friction).  Use a rule and make sure the ppi are what you want them to be - 12 will give you a balanced weave on this sett, like most of the samples in the Dixon book.

Finer threads will be a bit more elegant and distort the book spine less, but carpet warp will work. In cotton 10/2 or 20/2 would be thinner and allow more threads for more complex patterning in the width of a bookmark.  Other useful items for sampling include dish towels (cheap in 10/2 cotton!) and mug rugs (coasters).  There is a book by Penelope Drooker called Samplers You Can Use that you may find interesting.  It is out of print but can be found used and in guild libraries.  You might enjoy looking at the Complex Weavers Award ribbons, another type of use for narrow sampling bands.  I wove the ones in 2004:  <http://complex-weavers.org/awards.htm>

Laurie Autio

merrymac (not verified)

Thanks to all for the suggestions and info.  I believe I am beating too hard ... easy to do with that small an item?  The thread measures out at 20 epi when I do the ruler wrap method? 

I'm pretty stubborn and now have it it my head that I "can make a bookmark" successfuly!  Sooooo ... in a few days, I will try again but with a lighter thread?  I really was hoping to use the carpet thread for them, though, since I have quite a bit of that and I think it is good for trials? 

I will have to see about the book by Drooker.  I haven't seen one, I don't believe?  Also will check out the bag suggestion.  I'd really like to see what the material is going to look like before making final decision on something larger? 

Thanks again.  God bless.

Merrymac

claudia (not verified)

Merrymac,

When using the ruler method, make sure you wrap the yarns close to each other and the total number of wraps per inch is divided in half for plain weave and at 75% for twill.  Your wraps per inch do not equal your ends per inch.  That might be part of the problem.

I used up a whole lot of carpet warp on 6 placemats I just finished.  You can check them out here.  It was great, they are stiff being set at 18 epi but not inflexible.  They lay nicely on the table and not every crumb falls through.  One of the drafts showed lots of warp floats and I tried one placemat like that but it's a fork grabber so it'll stay in the drawer or get cut up into mug rugs.

Good luck with the bookmarks.  I think you may like the finer yarn.

Claudia

merrymac (not verified)

Well, duh.  Thanks so much for the info, Claudia.  I looked and looked through the weaving books I have and did not find that information.  It's probably there but I either skipped over it or didn't know what I was looking for?  I definitely have been beating way too hard!   :)

I've got a 22" warp on my Baby Wolf (Nemo) using the carpet warp.  I was (am?) hoping to get a decent pattern woven so's I can make a small throw rug?  But I may well switch that plan over to table mats so I can see the different patterns?  Then make a decision on the rug?  I plan on using carpet warp for the weft.  I have warped the loom with a 15 dent reed.  Is that going to make it too tight (again?  sigh.) 

I am now planning to warp my Gilmore with a finer thread to attempt the bookmarks or even the bag mentioned above? 

Before I forget, I really like your placemats. 

Thanks again.  God bless.

MerryMac

claudia (not verified)

The size of the reed is not the concern, it's the sett you are concerned about.  You can use a 15 dent reed and sley it every other hole for a sett of 7.5 epi.  Focus on the overall goal of the project, start with the basics, ept (and, therefore, sett), ppi and those will be determined by the yarn you are using and the hand you are trying to achieve.  Carpet warp is good for many types of projects but it is, at the end of the day, carpet warp.  

I have found the weaving calculator to be a very valuable tool, have you tried it yet?  It's here.  The fringe setting is not working you have to add it in yourself but everything else is great.  I know lots of people who are using and enjoying it.  I believe it's the best place for you to start.  When you wound the yarn around the ruler with the 8/4 carpet warp what did you get for sett?  The other place to find the answer to what sett to use is on Interweave's site, here.  Click on the Master Yarn Chart.  I believe they give 3 numbers for each yarn.  The first is the recommended plain weave sett, the second is for twill and the third is for lace.  You can check that on the first page. It's a great table with almost every yarn in it and the setts are already there.  I printed it and keep it near the yarns in my studio for planning purposes. 

I hope these things help you in your project planning.  The only other thing is to sample, sample, sample.  And don't be afraid to take the sample off the loom and wet finish it before you decide if it looks right or not.  Stretched out on the loom it's hard to really see what is happening.

Claudia

momframer1 (not verified)

I'm with you!!! I have no idea how to follow the draft in post #28 in the twill WAL to warp my loom. I've never used 2 heddles. Would you help me through the next step? I have the yarn. I have the 7.5 heddles. I have the will!!!

momframer1 (not verified)

Perfect, thanks Susan!!

momframer1 (not verified)

Thanks Susan!!!

I am so excited to try this out! These instructions make sense to me. I do have a few questions. When you warp for this you are using 24 warp thread over 9 slots if I'm reading this correctly. I am used to direct warping with 1 heddle where you pass 2 strands through each slot. There have to be some slots that you pass the yarn through twice (4 strands) to get enough warp threads. How should i do that? Do you thread the warp through both heddles at the time of warping or do you add the 2nd heddle in when you are arranging the warps into the right places? I know I am not using the proper terminology so forgive that please.-Deb

claudia (not verified)

OMG! Susan, you ROCK!

This is the most amazing, easy perfect explanation I have EVER seen.  Thank you, thank you , thank you.  I laid in bed, unable to sleep last night, thinking about the threading plan for this project.  I was hopeful I finally understood it but you have mapped it out so nicely I can just print and go.

It's really kind of you to take your time to help straighten this out for everyone.  Thank you,

Claudia