jander14indoor (not verified)

While I might disagree (again, being an engineer) and say a warp is exactly like a suspension bridge, fibers are just as much an engineering material as any other and all those things are calculable, I realize that's the, hmm, how shall we say, less than sociable side of me coming out.  I do realize I'm asking weaving questions and do appreciate your weaving experience in answering. 

 

I'm also a sometimes Cello player and understand that some of this stuff is better learned as muscle memory and experience.  I appreciate your reassurance that hand weaving is more forgiving and I can get good answers faster with experience than I can with calculations.  I also just need more projects behind me to get that experience.

 

On marking the loom to measure, I know no new loom comes that way, and no used loom I've seen (small sample, but consistent).  That's why I asked why something that seems so handy to me isn't so much in reality.  I will say it has helped this beginner in error checking as I thread and sley.  I assume this becomes less useful with experience.

 

Now to go try it (got the warp tied on last night) and start getting some of that esperience.

 

Hmm, I suspect the above in its side digressions isn't clear,

THANKS for the input. 

 

Jeff Anderson

Livonia, MI

jander14indoor (not verified)

Sara, your last comment came as I submitted mine. Correct, its a Bexell Cranbrook from the early '70's with the coarse warp beam ratchet and fine cloth beam ratchet.  Yet another adjustment from the Baby Wolf, but one that worries me less at the moment (hope I'm not missing something there).

 

It has multiple hang points on top of the frame for the beater, haven't counted them.  The beater also has adjustments to move the reed up and down. I have that set so the open shed is rougly centered.

 

But, you surprised me when you said the shafts can be hung in two positions.  I didn't see that on the instructions,  I don't I understand that.  There's a pin on the top beam that locks the jack frame in place front to back.  I don't see how the frame can move since the ties have to line up with the holes in the lams and treadles.  I know I can move the heddle frames up and down by adjusting the texsolv (I replaced the chains when I went to 8 shafts) but I thought the height should be set to have the warp threads run straight from back to front?  What are the two positions?

 

Thanks again,

Jeff

jander14indoor (not verified)

Thanks Sara, that makes sense on the positions now.  For future reference (since I don't always have to use all 8 shafts), what circumstances would have me move it to the forward or rear position?  I assume for everyday stuff the forward position is fine since that's where it goes with 8 shafts.

 

About my Cello playing, I'm a FAR better engineer than Cellist, and perhaps very like your husband.  I'm the loom mechanic as well as weaver and you can guess (being married to an engineer as you said) I always want to make things "better", sometimes at the expense of good enough...

 

And this project is relatively small, the Halcyon color gamp kit, and meant for learning more than anything serious (not that learning isn't serious).

 

Thanks again,

Jeff

claudia (not verified)

Hi Nancy,

I have been considering what could be causing your problems and a couple things crossed my mind. Are the heddles clear of each other and able to move freely as the warp is advanced? I have a few times found an errant warp thread that was caught on something in the shaft and it was preventing the warp from moving correctly. I would also check the cloth beam and see if everything is free to move there, nothing cathching where the warp is tied or lashed in front.

I hope this helps. Get a good light down inside the shafts and heddles and make sure it not in there. I'll keep thinking. It's happened to me before and I know how annoying this can be.

Claudia

Ellen (not verified)

I have a few times found that the tie on bar was not centered and got stuck against a side, which would pull the whole thing uneven. Just a thought. ?  It is so frustrating to have something happen you can't figure out. Sometimes it could be a help to have another weaver to stand beside or behind the loom while you weave to spot where something doesn't behave right. Alas seldom possible.

Good luck to you!

Guiding Myth (not verified)

 Hi Nancy,

You have done an excellent job figuring out the problem and coming up with the answer.  The paper should help.  What you are experiencing is common when the warp is beamed without heavy paper or sticks.  The "fix" is to beam with heavy paper between all of the layers - or to use lots of sticks.  When you beam without heavy paper or sticks the warp threads on the edge tend to slid off and wind on the beam rather than layer over the previous threads.  As you observed.  I don't know why it happened on one side but not the other.  It could be that the tension when winding on was slightly different on one side.  If it never happened before - well you were either lucky or (there are so many variables)...the yarn is different, the warp is longer this time, when you beamed the warp you used less tension.  

Centering the warp would have no effect.  I have to admit that I often misjudge regarding centering - as long as its not so bad as to make weaving uncomfortable - so what!

Just make sure the paper you use is heavy 60 lb or better.  Some people use rolls of cardboard.

The important thing is that you are on the right track!

S. Stanley

 

dteaj (not verified)

Paper and sticks are really useful. Another possibility: was the winding on tension the same on both sides? Using a warping valet and equal weights on each warp chain can help with this...

Debbie

Ellen (not verified)

I started out using paper and sticks when I learned to weave.

But many years ago I switched to using this fortified heavy plastic that people use to cover their trailers with, cut into strips of the width I need. and normally 3 to 4 meters long. This works wonderfully and is so much easier to use, I think, and I have seen a lot of weavers use it here in denmark. Just an Idea.

I don't know what it is called in America, but I'm sure something like it must be around.

Woolwench (not verified)

I came to this site looking for help with this very same problem. The side threads were getting tighter and tighter as I progressed. I cut off the weaving (sigh) and rewound the warp with sticks. All better :-) Learning curve.

lkautio (not verified)

If the paper and rebeaming didn't work, and you have a folding loom check whether one side is not fully extended or is out of square.  I've seen this happen on a variety of looms.

Laurie Autio