dognapper2 (not verified)

(mis)Adventure UPDATE:
 

I cut off the 1st set of heddle strings and prepared to scrap the project. But I had carefully saved the cross as I considered whether or not it was worth a try to change out the heddle strings to match same as warp.
 
I FINISHED it!   Not sure I did the braid ends right but it is D.O.N.E!!!   
It's a little "primitive" as my daughter said "I like it...it looks primitive." :)
I can accept that!
 
Weaving did get easier, although after a few inches started matting up again. The first & last warp (the ones that had a slip knot to start with) were not the right tension - too loose - and contributed a little to the funky edges. Along with all the other things that this beginner did wrong, I'm sure.  But I'm so pleased to have completed it rather than quit.
 
I was wondering about an extra cross - to control the sliding around issues, of both shed rod & the ends themselves. I thought I might have missed a step. I drilled extra holes in the knitting needle I was using as a shed rod and it seemed to help.NEXT TIME I will add the extra cross in the back to see if it will help with stability.
 
THANK YOU for the wonderful introduction to this art!! Your blog, articles and tutorials are amazing. Above & Beyond HELPFUL. As well as the supportive community I've found here. Thank you all... I look forward to following the helpful advice offered!!!
 
Laurie in Maine ;)
 

Caroline (not verified)

Laurie, that looks good! Please put it on the projects page. Its good to have a record of how we progress.

Your selvages will come good - its something every weaver has in common, and we all struggle with it. The more we concentrate, the worse it seems to get, so its probably something we should not obsess about.

Have you fulled/washed your scarf yet? You will find that once that has happened, a lot of the faults you can pick out now  will even themselves up, and that the selvages are not nearly as bad as you think. Also, remember, you might know what went wrong as you were weaving - its not nearly as obvious to the rest of us, so give yourself a pat on the back! Well done!

franee (not verified)

It looks lovely! I'm so impressed that you kept going, you have a right to be proud. :D

I also have problems with my edge thread getting looser as I go and I can't blame the knot, because it is definately not slipping :)

Fran

dognapper2 (not verified)

Yes, you are right in saying "you might know what went wrong, but..."!

The picture shows the 2nd half of progress in the top fold. I can see improvement, but also exactly where heddles were changed; where they started acting up again. A couple of places where a sticky warp was out of place or more tension issues.

In the lower fold I see where I moved (smooshed?!) rows with my finger and they all moved in a wavey line :) Possibly a couple of places where I opened and closed a cross without throwing the shuttle through...not sure but it felt like I might have at done that a time or two.

Eagerly looking forward to the lesson in 2 color work ...will actually try sticking to the Beginner Lesson 1 page!

Laurie in Maine

rose Goldielocks (not verified)

Looks great!  (much much better than my first try, which got rolled up in a bundle and shoved in a corner for a couple of years!  I moved on to inkle with, and came back to backstrap ... by that time, I knew how to deal with sticky heddles/sheds)

Handwash the textile, and let it dry, and then look at it to see if you can still find the problems, but remember, normally only another weaver/textile person can pick such subtle changes up.  Be sure to measue the backstrap before and after washing, and keep a record (the projects page is great for that!). Next time you do plainweave on this kind of yarn, you will know how much it shrinks after washing!

 

Caroline (not verified)

I use small fishing weights to keep unruly warp threads under tension. They come in all different weights and sizes, and all have a hole in them, through which I stick a jewelry wire finding to make a loop I can use to attach it to the warp/s that need the extra tension.  I have also used a fishing weight when I have missed a warp. The missing warp is wound around a little paper bobbin, weighted then it hangs over the back beam independently of the rest, but under the same tension. You could also use the weighted wooden bobbins used for kumihimo - they are much prettier.

franee (not verified)

Hi Laverne,

Thank you so much for letting me know it's not just me :)

I have to take a photo today of my progress, I have been going in the order of the tutorials and am finishing my piece from Tutorial 3 - one weft double weave - it has been a steep learning curve!

Fran

francorios (not verified)

Good for you!

I think it looks great. The braids look fine too.

Every piece builds experience toward the next piece.

Edges are one of those things we are continually striving to perfect, or at least improve.

Have a good day!

bibi (not verified)

 lol, in yours it's a rabbit ??? in mine, as I was taught by my nautic teacher, it's a snake which comes out from the well , goes around the tree and go back into the well ! I know the name in french : "noeud de chaise" which if you translate word by word would make "chair knot"... does chair knot exist in your language ???... checked into the dictionnary and it seems you call it a "bowline" !

HAPPY NEW YEAR EVERYONE !

Michelle

bibi (not verified)

euh... well... I just repeat what I've been told... and I do agree with you, what on earth a snake coming out of a well has got to do with a chair ???!!!  and all of this to be used on a boat !!

my wavy waves are waving quite well... I was very busy packing all my stuff these last days, so I didn't wave much, but, I'll do my best to show you very very soon... as soon as light comes back (it's already night here )