TinaHilton (not verified)

I have some Procion dyes.  Does that count?  I actually did use the dyes at Convergence in 2008.  So I have dye, and I have fiber to dye.  I just need to actually dye!  I have tencel, tencel/silk, and bamboo that I bought just for dyeing.

tien (not verified)

Hi Su,

I used to dye with Procion dyes but have moved over to Cibacron (Sabracron) F, available from Pro Chemical.  It's also a fiber-reactive dye - requires slightly higher temperatures for vat dyeing than Procion MX, but is WAY easier to wash out excess dye afterwards and the color in the dyebath is much closer to the final color than with Pro MX.  It isn't available in quite as many colors, but since I usually mix my own colors it isn't an issue for me.

Tien

Little Meadows (not verified)

A general question for Procion/Sabracron dyers;  last night I sat at the back listening to a small group of weavers talking about their tencel dyeing workshop and having to rinse and rinse.  Now I read these posts and read about rinsing out all the dye.  As I mentioned above I use the Acid Washfast dyes on my sheeps' fleece and when I do I have complete or darn near total take up and have clear water going into my spetic tank.  So what gives that when dyeing cellulosic with appropriate dyes the fibers aren't fully taking up the dye?  Liese

tien (not verified)

Hi Su,

What I've found is that, with MX, it takes four or five rinses to get the water to run clear.  With Sabracron F, it only takes two rinses.  Also with MX some of the colors look different in solution than they do in the finished fabric - can 't remember which ones offhand, but it was enough to be noticeable.  Of course, your mileage (and water, and dyeing methods) may vary...

As for why the dye doesn't take up completely - it's because fiber-reactive dyes react with water as well as with the fiber, so some of the dye bonds to water and won't bond (permanently) to the fiber.  This means some dye stays in the water, and some clings to the fiber without bonding permanently, so there will be dye in the water and in the rinse water after dyeing.

Tien

Little Meadows (not verified)

Thanks to you Sue and Tien for your thoughts but I just can't think this is right that the dyes if weighed & measured used with weighed and measured fiber should bleed like this.  Rinsing this stuff down the drain is polluting; I've talked to Bob a bit last night,  he's an inorganic chemist and I'm going to call Pro Chem on Monday to get more tech info so will report back here with what I learn.  Bob's worked for many years in water treatment in automotive plants so hopefully tech service can tell me what  the components of the MX dyes are and he can weigh in on what he knows. 

Liese

Little Meadows (not verified)

Just following up on what Pro CHemical Tech support had to say...which wasn't much.  Any info about components in the dyes is proprietary,  they are made in India & China, the best & only solution she had was to set the rinse water out to evaporate and then dispose of the residue in with hazardous waste.  So if and when I decide to dye my tencel I'll set up an evaporator, that would allow me to see how much these solids amount to.    Liese

Little Meadows (not verified)

I think you are exactly right!  Imagine those fringes all barber poled versus what you did ... your fringes compliment the scarf much more than they would otherwise.   Now may I ask about your red waste yarn?  Why do you do this and not use tabby for the first 2-3 picks?  Liese

Ellen (not verified)

Hi Liese,

Well, I always start out any new weaving with a couple of picks of another yarn (from little bits of leftovers you always have lying around) preferably in a contrasting colour, and preferably something very smooth when I plan on fringes.The first because it is often easier to spot possible mistakes in the set up, I find, and the second so it is easier to slide out the yarn 10 or 12 threads at a time, when I get to twisting. And very often I do patterns where there are no tabby shafts, as with this scarf, for example.

I suppose you do many things just because that's the way you learned it in the first place and never considered any other alternatives. That's one of the things that is so great about this Weavolution : you come across so much inspiration :-)

And what I especially liked about these fringes was the very nice way they seemed to be balanced and close to the fabric, when I tied the first half-knot.

Ellen

Little Meadows (not verified)

Well, I  think you've given me enough reasons to try your method with the waste yarns and compare the finishing to what I've been doing.  I've been  hemstitching, so my fringe bouts are all ready to go but that gives me a different edge to my pieces than what I see on yours.  Sometimes it's the little details that make a difference.  Liese

Ellen (not verified)

Glad to have inspired you to try :-)

I have tried hemstitching a few times, when first following instructions from a Handwoven draft, but never liked it much, and don't consider it necessary with the method I use.

I looked for examples of your scarves, but didn't see any. But what a wonderful place You have got :-)

Ellen