Ariaya (not verified)

Well I'm going to just get in there and do it :)  Maybe not tonight though ... I'm not sure what time I'll get home so that'll make the difference :)  I'm aiming for white/offwhite with blue stripes ... it'll go perfectly for my grandmother's house if they come out okay.

 

francorios (not verified)

Hello Ariaya,

Thank you for joining the WAL. This will be ongoing over the next few days. So jump in when you can. Blue and white is always a good combination.

Thank you again!

Have a good day!

sandeleh (not verified)

I'm worried that some people may not have chairs that can be used for warping pegs. If someone has a challenge, let us know and we'll see if we can figure it out in the group.

 
That would be me!  LOL - see, there was a reason I bought the warping reel - I have no chairs other than one recliner and one adjustable office chair.  Neither has knobs on the top of the back or legs that I could use to wind warp on.  No table here to use a peg with, either, so I guess I'm stuck with the warping reel.
 
I went by Joann's today, too and scored a 14oz ball of beautiful varigated with turquoise and purple and white.  No pix yet, and I still have a scarf on the RH loom that needs to be woven off before I can wind on my cotton warp and start on my towels.
 
Thanks for the welcome and I will be a good girl and not get too uppity. :)
 
Sande in Fresno, CA, USA
 
 

Caroline (not verified)

I have warping posts that I clamp to a flat surface, but have similar space problems to you Sande. My last warp was done on top of my clothes dryer, as it was the most level space free at the time, and longer than my kitchen table. NO PICCIES!!!!!!!!!!! Thats one bit of DIY I keep to myself, lol! Just as well I don't do many long warps, hehe!

francorios (not verified)


Next, I laid out the warped loom on the floor. I open up some brown paper grocery sacks and cut them up so I can use them to wrap around the warp as I roll the warp onto the loom. As the warp goes around the loom bar, having paper to separate each layer helps the warp stay on the same level, allowing for even tension on the warp. Without a separator, the warp can be high and low on the loom bar, allowing for uneven tension.

So I comb out the warps with my fingers to be sure there are no tangles before I roll the warp onto the loom bar.


In order to get some resistance, I tied the warps to a weight (the bar stool) so the warp has something to pull against while I roll the warp onto the loom bar. I am warping on the floor this time. I usually enlist the aid of a boy to assist me while warping on the kitchen table. I can usually find one of my sons in the kitchen or on the computer, but I'm trying to do this solo as to explore possible solutions to problems.

This worked okay. In the past I've tied soup cans to the warps bunches and hung the warps over the edge of table. That was okay, but not great. If I find a great way to get resistance on the warps by myself, I'll post it. Spent over an hour playing with the paper and rolling the warp. Call it a day.

After a few days not weaving, I jumped back to the loom and started off. I forgot to take pictures of how I did the tie up on the loom. So here is the front loom bar. Notice the big loops?! That will come back to bite me later at the other end of the warp. Because I came up short a few inches on the other end! Because I used so much warp here on the tie up I ran out of yarn on the other end of the warp. So remember to wind your warp up as high as you can with as little knots on this end as you can.

 

francorios (not verified)

I wound the warp on as tight as I could to the warp beam (the far one). Then I tightened the knobs on the cloth beam (the near one). Then I tightened up the warp beam again. There was a little bit more slack in the warp beam then on the cloth beam.

I use shoelace knots when tying onto the cloth beam so I can untie and re tie as needed. Its very important to get the warp as evenly tight as you can. Uneven tension leads to uneven weft rows and wobbly selvedges on the sides.

Especially important is the outside inch or two on each side of your work. So be sure that your warp stays straight on the warp beam and that each warp layer is firmly on top of the layer below it under the paper. If the warp spreads out, the top layer has no layer below to support it and it falls down, creating loose warp on the outside warps.

So take some time to work on good tension, getting it evenly across the whole width.

Have a good day!

PattyAnne (not verified)

Hmmm.... I'll have the give the 'tensioning stool' a try!! 

 I think that I had the problem you spoke of Franco.  My outside warp threads kept falling off the paper because my paper was a tad too narrow.  I didn't think it would matter, BUT,  as I wove, I noticed that  my selvages were really weirdly loose and I couldn't figure out why.  I BET it was because of those loose outer warp threads.

Here's a picture (not my dish towels but rather something I had tried earlier).  Do you think that is what happened - the outside warp threads fell off the paper?  Would that cause the center part of the weaving to be fine and the outer edges to be messed up like this?

francorios (not verified)

Hi PattyAnne,

I get that same thing on my dish towels too. The inside warps seem to migrate closer together. The outer warps look looser. When I put the cotton towels in the wash dry cycle, it evens out a lot.

But I wonder if the spacing of the heddle is just too far apart for the yarn?

I usually use an 8 dent heddle. I have a 10 dent that I want to use next to see if the spacing is the issue. I know that even though my project is warped for 16 inch, it wants to narrow in to 15 1/2 inch or even 15 inch. I try to keep it at 15 1/2 consistent so at least it is an even width all the way.

Tomorrow I'll post "weaving in progress pictures"

Have a good day!

Caroline (not verified)

Another trick is to have a selection of old film cartridge cases, or pill bottles and use those to weight down any wayward warps. You can add nuts and bolts, or fishing weights inside them too.

And for those who do not have a handy stool when trying to keep their warp under tension, a bottle of water, tin of peas etc will do - I have a moggy who loves swinging on chains of warps, lol!

quejimenez (not verified)

hello everyone!

i'm very new to the group (just joined) and equally new to weaving.

i'd love to join this WAL but i may be a little slower to begin and will have to play catch-up next week. i just ordered my loom and yarn and will be waiting for it to come...hopefully friday but no later than monday.

i will be working on a kronski 32" harp...i have coming with it : an extra 10-dent reed (for doubling up), a 12-dent reed, an extra pickup stick...textures and patterns book and a ton of yarn.

i'm not sure if the yarn i bought was correct, but if i need to (and if possible) i can go to jo'ann or michaels to find the appropiate yarn...i've got a bunch of 8/4, 8/2 and some 20/2 (i think) cottom coming.

i'm really excited to join this community, i'm completely new to working with fiber arts...extremely new.

as soon as i get materials..i'll get to work and post progress...i hope that is okay.

have a wonderful day!

btw, franco i'm swooning over what you have going so far!