claudia (not verified)

Hey Joanne,

There are lots of Harp users here, welcome.  I'll go join the Kromski group, too.

As for the cords, you can also get in touch with New Voyager Trading or just buy some nylon cord.  I keep tons of the nylon cord because I use it to lash on my warps.  I bought a roll at the local hardware store for very little money.

It is very important that the cords be the exact same length.  If you are a quarter inch off it will have a very negative effect on the warp tension.  If you shorten one, shorten them all or just use a different method for attaching the apron bar onto the beam and not worry about it.  Even tension is everything so be careful

Claudia, RH group moderator

claudia (not verified)

Hey Joanne,

There are lots of Harp users here, welcome.  I'll go join the Kromski group, too.

As for the cords, you can also get in touch with New Voyager Trading or just buy some nylon cord.  I keep tons of the nylon cord because I use it to lash on my warps.  I bought a roll at the local hardware store for very little money.

It is very important that the cords be the exact same length.  If you are a quarter inch off it will have a very negative effect on the warp tension.  If you shorten one, shorten them all or just use a different method for attaching the apron bar onto the beam and not worry about it.  Even tension is everything so be careful

Claudia, RH group moderator

quejimenez (not verified)

 Claudia,

i took your advice concerning my irregular nylon cords on my harp and yesterday morning sat myself down and fixed them up. it wasn't as bad as i thought it was going to be and i came away with a bit of a trick to do it (at least to me). maybe this will help other kromski harp newbies/owners.

What i did to get even tie on strings:

first off, the first time i did the burning and connecting i got most of them "about" the same size...and figured it was okay...well thanks to claudia, after my first project (which did have some tension issues...which i thought it was because of my inexperience...but was probably because of my strings) i decided to re-burn...and it wasn't as hard as i thought...

i took out my quilters pressing board (basically a padded ironing surface), grabbed some quilting pins and pinned all the loops down...and stretched them out...and measured them using the guides on the pressing board.

from there i was able to see which ones were closer in length...and devise a strategy...

i had to cut about 4-6 cords and shorten them because one cord was about 1/4" shorter or more than the rest.

i measured that one out...pinned it to the board to hold it taunt...cut the burned tips of the longer cords....and measured the cut one to already connected cord...i cut the cord to be about the same length connected...with a little extra to allow for burning and melting.

i then burned the tips (just a bit at a time) and while they were still hardening measured it around the straight pins to see if i was on target...if i wasn't it was still soft enough for me to burn more if need be.

i did this for all the cords that needed to be shortened...and created two sets.

the two sets are not the same lengths...but all the cords in each set is the same length...i.e. the cords in the back beam are all one length...and vice versa...but the back set and front set doesn't have to be the exact length...just as long that all the cords are the same in its set.

okay...i hope that made sense and will help.

sorry its so wordy...its one of those things that takes a bit more to explain than to do...

and hey....i told myself...if i mess it up..it'll just be a trip to jo'anns to get some more nylon cord...once i realized that...the fear was gone!

enjoy your harp's they are wonderful and a joy to weave on!

quejimenez (not verified)

 Claudia,

i took your advice concerning my irregular nylon cords on my harp and yesterday morning sat myself down and fixed them up. it wasn't as bad as i thought it was going to be and i came away with a bit of a trick to do it (at least to me). maybe this will help other kromski harp newbies/owners.

What i did to get even tie on strings:

first off, the first time i did the burning and connecting i got most of them "about" the same size...and figured it was okay...well thanks to claudia, after my first project (which did have some tension issues...which i thought it was because of my inexperience...but was probably because of my strings) i decided to re-burn...and it wasn't as hard as i thought...

i took out my quilters pressing board (basically a padded ironing surface), grabbed some quilting pins and pinned all the loops down...and stretched them out...and measured them using the guides on the pressing board.

from there i was able to see which ones were closer in length...and devise a strategy...

i had to cut about 4-6 cords and shorten them because one cord was about 1/4" shorter or more than the rest.

i measured that one out...pinned it to the board to hold it taunt...cut the burned tips of the longer cords....and measured the cut one to already connected cord...i cut the cord to be about the same length connected...with a little extra to allow for burning and melting.

i then burned the tips (just a bit at a time) and while they were still hardening measured it around the straight pins to see if i was on target...if i wasn't it was still soft enough for me to burn more if need be.

i did this for all the cords that needed to be shortened...and created two sets.

the two sets are not the same lengths...but all the cords in each set is the same length...i.e. the cords in the back beam are all one length...and vice versa...but the back set and front set doesn't have to be the exact length...just as long that all the cords are the same in its set.

okay...i hope that made sense and will help.

sorry its so wordy...its one of those things that takes a bit more to explain than to do...

and hey....i told myself...if i mess it up..it'll just be a trip to jo'anns to get some more nylon cord...once i realized that...the fear was gone!

enjoy your harp's they are wonderful and a joy to weave on!

alms (not verified)

I am new to the group[ - recieved a Kromski 24 inch plus stand for my birthday in August - really like weaving on it .  Also bought myself a 12 inch Ashford knitters loom to travel with - knit a mohair scarf on it - warped it too thick so have a couple of ideas for my next try wit h it [bulky Robin Illusion yarn from years ago]  Also knit a blue and green Fibbonacci series scarf for a friend of mine when I was up visiting her -using her yarn - don't have pictures but it came out pretty cool.  I prefer the Kromski - am thinking of following one of the members suggestions and using the tesslov instead of the plastic warping stuff - don't like the way the plastic attachments feel, look, or work when you are warping - any other suggestions?  Anyone know how long a warp you can weave on the Knitters loom? Thanks

alms (not verified)

I am new to the group[ - recieved a Kromski 24 inch plus stand for my birthday in August - really like weaving on it .  Also bought myself a 12 inch Ashford knitters loom to travel with - knit a mohair scarf on it - warped it too thick so have a couple of ideas for my next try wit h it [bulky Robin Illusion yarn from years ago]  Also knit a blue and green Fibbonacci series scarf for a friend of mine when I was up visiting her -using her yarn - don't have pictures but it came out pretty cool.  I prefer the Kromski - am thinking of following one of the members suggestions and using the tesslov instead of the plastic warping stuff - don't like the way the plastic attachments feel, look, or work when you are warping - any other suggestions?  Anyone know how long a warp you can weave on the Knitters loom? Thanks

armanda (not verified)

Hi!  I live near Harrisburg, PA and I have been weaving about one year.  I mostly make things using color and texture in plain weave, but I am starting to plan more complicated projects.

armanda (not verified)

Hi!  I live near Harrisburg, PA and I have been weaving about one year.  I mostly make things using color and texture in plain weave, but I am starting to plan more complicated projects.

Barbara Fessler (not verified)

Hi:  I have a shop/studio just outside of Millersburg, Pa about 35 miles north of Harrisburg.  I've been spinning, weaving and knitting for 20 plus years. 

 

Barbara Fessler (not verified)

Hi:  I have a shop/studio just outside of Millersburg, Pa about 35 miles north of Harrisburg.  I've been spinning, weaving and knitting for 20 plus years.