caloosa (not verified)

I am a new weaver and concerned about the loom waste involved with hand spun warp. 

Will I get over this or is there a solution that I am unaware of?

 

Charlene

jj50 (not verified)

I have been using hand spun as warp since I started spinning because I don't know how to knit or crochet. I learned that worsted spun is the best method of spinning for warp so that how I spin the majority of my yarn. I prefer 2-ply, but I'd like to try wool singles sometime. I've never had a problem with warp breaking except for my first alpaca warp in which I had a bad join and one of the plys came apart. So far I've woven with alpaca - suri & huacaya, wool, silk, linen, cotton blended with silk, and silk-wool blend. I've never used sizing.

Charlene, for a long time I only used my table loom when weaving with my hand spun to minimize loom waste.  I got over it eventually, and mostly because my table loom has only 4 shafts, I started using my floor loom with 8. I have a nice collection of hand spun thrums. :~)

Jan

Kurt Pippin (not verified)

Hi, Liana--

Which spindle or wheel do you use for making the big chunky yarn?

Pippin

liana (not verified)

Hi Pippin,

I use an Ashford Joy for most of my spinning.  It has a "Wooly Winder" for spinning any size yarn imaginable.  I also have an Ashford Traditional I won in a silent auction that I have all the sizes of bobbins for and the country bobbin size is great for chunky yarn especial when I am plying because the 2 or 3 ply needs a big bobbin if you want a lot of yarn.  I had a spindle that I knit directly from the spindle to the knitting needles.  It works great for a fine, delicate angora yarn.  The spinning of singles though, in either knitting or weaving requires a bit of extra twist so that when it relaxes it doesn't untwist.  Then when you wash it, it fluffs so beautifully and it fulls some to give you a solid structure that will never unravel.

You also asked how I use my handspun on a loom as the warp.  I use a rigid heddle and I over-twist the yarn and set it.  The it works well.  I haven't tried the starch or gel because I haven't needed it, yet.  But I do like the comments from those who have.

As far as advice goes, I suggest you do as I do, read, read, read.  And then try it for yoursel.f.  There's no amount of reading that can substitute for experience.  And your own experience is the best place to start because then you know the questions to ask to hone your craft.  And you have something to show, that, for example, let's you ask, "This is sett to close and is too thick, how do I change the sett and what should I change it too?"

I am so grateful to the weaving community for making so much information availble that I can learn from my home.  I never would have done what I have if it wasn't for the books and magazines availble.  They inspire and teach so much.

Hope this is helpful.  Just one person's opinion!

Liana

jenadina (not verified)

You might enjoy reading about Holly's process at hjsstudio.com. She weaves with low-twist handspun singles as both warp and weft and has a rundown of an entire project (a coat) from start to finish. There are also a few articles there about spinning low-twist singles.

Alison (not verified)

Here are a few more thoughts about spinning handspun for warp:

It has to be able to withstand the tension and the abrasion of the reed and heddles.  So a softly twisted yarn generally won't work (unless fulled before warping) unless you weave it under low tension, perhaps with a bulkier yarn (fewer beats - less abrasion).  Practice your joins as a bad join can fray with the abrasion.  I think the sizing idea is great, at least until you're confident enough in your spinning product.  You can also test your yarn by running it against something smooth but hard such as between your fingernails, or in a reed - you get the idea, something to simulate what the yarn will go through.

Regarding reducing loom waste - another thing you can do is to tie on your warp rather than start with a new warp.  There are a number of sources for explaining how it is done.  One of the ones I have is in one of Peggy Ostercamp's books.  In short, you tie your warp threads to a set of warp threads already on your loom (for example, from you last project).  I haven't done it, can someone else explain it?

 

Alison (not verified)

Nice lace picture, btw - did you make it?

Kurt Pippin (not verified)

I decided last night on a Fricke single treadle wheel with the WooLee Winder and 4 bobbins, plus the Jumbo Flyer/Bobbin with an extra jumbo bobbin.

We can always save our thrums and toss them into the carder to make 'art' yarns.  :-)

While I'm waiting on the wheel, I'm getting some drafting experience on a variety of top-whorl and Turkish spindles, and something called the Rakestraw Spinner, a paddle spinner that turns like a party noisemaker. My first plied Icelandic wool yarn is drying in the laundry room, and a couple of Rakestraw singles are resting.

And, yes, reading reading reading.

Kurt

dteaj (not verified)

I've used a dummy warp once when I had a limited amount of fiber and hence yarn, with no access to more. There's a picture of the dummy warp with the project. In this case, I didn't tie on to a previous warp. I just used junk yarn to eliminate the loom waste on this short warp. I probably eliminated about 18" of waste. My Schact typically has 24" of waste. Let me know if you have any questions.

 

Kurt Pippin (not verified)

'I have read that some of the most meticulous weavers in Scandinavia would never dream of spinning their warp by any means other than on a handspindle. In their opinion, a spinning wheel was fine for making the weft, where minor inconsistencies would not threaten the weaving's sound structure!'

from Spinning in the Old Way by Priscilla A. Gibson-Roberts

She also writes that a high-whorl spindle can reach the speed of the average spinning wheel. I have far to go....

Pippin