janh (not verified)

 Hi there -

My backstrap is a length of blue nylon (?) belt material - sort of like a seat belt for an auto.  I put LARGE key rings in the ends and use a baby-diaper-size safety pin to secure the rings in the belt.  It isn't the most wide belt in the world but it seems to work.

The other end of the backstrap "loom" is a length of green cord from a mountain-climber of some sort.  I put an overhand knot in the middle to make a loop and put loops in the ends.  I use a carabiner to attach the middle loop to an eye-bolt that is in my floor loom and the end loops attach to the loom bars that are tied to the warp.

The warp is twined onto small diameter dowel that is attached to the loom bars (a broken closet pole).

Photos are below.

J -

francorios (not verified)

This weaver in Bali, Indonesia is using  a stick instead of a backstrap.

http://iweb.tntech.edu/cventura/Songket.htm

Notice also that her work is on a kind of frame.

Have a good day!

Franco Rios

Caroline (not verified)

A lot of the far eastern weavers sit with their feet straight out, and many of them do push their feet up against the far beam of the loom. I'm not sure if this is how they tension it - Carol V thinks not, but  lot of the older photos I've seen suggest they do. If you check the file I directed Virag to, there are some fantastic photos of Taiwanese weavers, and their looms have the most amazingly large back beams - they are these hybrid looms that are semi-portable, though I'm not sure that these are, hehe! Also, in the book I have on Ladakh, the warp is stretched straight out, and held down by large stones or rocks, so they must move towards the back beam as they weave!

Found the url for the Taiwanese weavers!

www.cs.arizona.edu/patterns/weaving/articles/nb55_abr.pdf

francorios (not verified)




Here is an easy way to rig a backstrap. Take a belt that fits around your waist. Put two loops of rope through it that extend about 12 inches from the belt.




Place the belt around your back with the buckle facing away from your back and the loops extended.



Hook the loops onto your loom bar. You will have to experiment a little bit to get the right loom length. It's not fancy but should hold up until you weave a fancier backstrap.

Have a good day!

francorios (not verified)

Update on my backstrap project

I had to re-warp my backstrap project due to crossed warps and other issues. And I lost my shed sticks before I tied them so I tried to pick my way back, but it was easier to take it apart and re-warp. Which I did.

I'm letting it sit for a couple of days until I'm not mad at it anymore before I start to weave. If I was in a more primitive setting I would go out and shoot a buffalo.

Have a good day!

francorios (not verified)

 

Here is the finished towel. Woven dimensions were 16 inch wide, 24 inch long.

Off the loom without tension, it only measures 13 wide, 21 long. I haven't even wet finished it yet. That would reduce it another 10 percent. I had some missed picks, but I wasn't expecting perfect on the first try anyway.

Peaches & Creme cotton worsted yarn white warp/weft, Sugar & Creme cotton worsted yarn variegated black/white for borders. Sett is 8 per inch. Woven on a backstrap loom.

Have a good day!
Franco Rios

Aquinnah (not verified)

 As I am heading off to get some dowels tomorrow to make a loom, I am reading old bits to ensure I am not forgetting about anything: I noticed that Laverne asks how to make a good backstrap: am I being too obvious, but wouldn't weaving a nice, broad band be the thing? OK maybe the pillow case improvisation at first, but then a nice band. Or am I missing something crucial here?

I already have one, passed on to me from an elderly relative. It's arather coarsely woven band, I think the kind of thing used for saddles et c(I am not a rider so I could be very wrong here), in a natural colour, with leather toggles attached at either end, to hook onto a stick in front of your body. Now looking at it more closely it looks rather homemade, but I hadn't realised before so it is also well made. 

Aquinnah (not verified)

 I am moving ever closer to starting something: Today I went and bought bits of dowelling etc (I find my broom handle rather useful when attached to my broom, so short of chopping down a tree branch, buying a dowel was, for me, just now, a must). Now I have plenty dowl. next fix a something on the wall where I can affix said dowel. Etc, etc. slowly getting there!

I have also decided (I think) that left over bits would make a really nice Christmas pressie for my daughter - a small portable homemade loom! What better! Even my husband got excited about that!

By the way, Laverne, each time I look I find something new on this site: Today I found links to your bits of work. Wow!!! They are lovely! And makes my finger itch to start having a go! I liked the knobbly edged beginners strap too. it gives it a nice homemade look. I was also impressed by the pic of your danish friend weaving by the roadside! Way to go!

Aquinnah (not verified)

 We'll see. It would be nice wouldn't it! But sometimes I find that my intentions and my actions don't exactly meet - a gap, at times, as wide as an ocean! So, as yet, one step at a time. 

DianneStucki (not verified)

Okay, I've been reading everything I can find--including repeated readings of Laverne's article on Weavezine--and I have one question I'm just not completely clear on.


As you work your way up the warp, do you wind up scooting closer and closer to your anchor point?