In another thread, Michelle asked:

Hello Weavers,  I have been looking on the internet for boat shuttles.  There are quite a few to chose from. I would like to purchase a couple of boat shuttels and a bobbins winder.   What is a good one  to use with a Schacht Pup Loom????  TIA  Michelle

Any suggestions?

Comments

Weavalong (not verified)

Boat shuttles are very useful, mine are very well loved and used every day. I bought two 10" boat shuttles which takes 4" bobbins on E-bay.  I have seen a double bobbin boat shuttle and think that may be very useful as well when working two colours.

 

I bought an Ashford bobbin winder and find it does the job. When I ran out of bobbins the other day it was easy to make-do with a piece of stiff paper tube secured to the winder with cellotape. The bobbins are best but the paper ones are  just as good.

 

I work on an Ashford 4 shaft and don't have a beam to run the boat shuttle along, it goes directly over the warp threads and it works well for me. Your loom looks similar to the Ashford 4 shaft so its possible you'll also be happy. Happy weaving!

termiknitter2 (not verified)

If you have a power drill - cordless or regular you can purchase a threaded rod that will go thru your bobbins and 2 wingnuts.  I put the rod in the drill just as if it was a drill bit, then tighten.  Add one wingnut then the bobbin then the 2nd wingnut  - make sure that the bobbin is snug between the wingnuts.  Tie the yarn onto the bobbin and start winding.  Hold the yarn and control it loading on the bobbin - I do it in diagonals back and forth.

It is cheap if you already have a drill.  

Weavalong (not verified)

Great idea in an emergency..........

There are drill stands available but then you may as well buy a bobbin spinner.

 

 

 

Joanne Hall

When purchasing a bobbin winder, remember that the thin spindle bobbin winder will wind cardboard quills, paper and plastic and wood bobbins.  The thick spindle will only wind the bobbins.  And if you make paper quills on a thick spindle bobbin winder, you need to reinforce them with glue or use thicker paper, as they may collapse when you use them.  The paper quills made on the thin spindle winder are easier to make.  Joanne

Weavalong (not verified)

I imagine PVA glue would do quite well reinforcing card "bobbins" I'll try and make some..

Shall investigate paper quills, didn't know about them.

Jim the Mudge (not verified)

I made the threaded rod, wing nuts and drill system.  Works great and is inexpensive.  You may find a used drill at a garage sale or flea market fairly cheap.

swelch (not verified)

I have spoiled myself a bit equipment-wise... I am a fan of Bluster Bay and AVL end-feed shuttles and the AVL electric bobbin/spool winder.  For shuttles, I seem to go back and forth between my Bluster Bay mini 11" end feed shuttle and my heavy, 15" AVL end feed shuttles.  The Bluster Bay is just plain pleasant to the eye and hand, while functioning very well, but sometimes the extra capacity and weight of the AVL shuttle lure me away.

As far as bobbin winders go, I've used an adapted drill, one of those Swedish winders with gears, and a few varieties of double-ended electric winders.  I now use an electric AVL winder outfitted with a tensioner and yardage counter, as it works well and very fast for spools, pirns, and bobbins.  I couldn't design a better winder if I tried, and I'm an engineer who loves to tinker and improve upon things.  The only downside is the hefty price!

Hope this helps!

mneligh

I use an electric winder with yardage counter which also works for sectional warping spools.  It is great, but if I had to do it all over I'd get a Swedish crank-type winder because I frequently weave in places there there is no electricity (including my house during ice storms, but mostly museum & park events).

I have also been known to put a slip of paper over the shaft of a drop spindle or great wheel and slide the yarn cone off it and onto the shuttle.  This works best with large shuttles or rag (not ski) shuttles.  This bypasses the need for a winder.

Shuttles are very personal and depend on your hands:  which can you grip better?  Fat like Bluster Bay or slim like the narrower Glimarkra?  In general the bigger and heavier ones carry more weft and are easier to throw across wide widths, but make sure the length of your shuttle does not exceed your turning radius (edge of weaving to wall or other obstuction).  I also prefer blunt-end to narrow end.  I haven't noticed that solid vs open bottoms make a difference, nor do wheels.

One other consideration:  if the ends of the bobbin areas narrow too quickly, pulling sidewise on the weft of a side-feed shuttle will cause some bobbins to stop and not turn.  This is annoying, but can be remedied by bobbins that have little sleeves that protrude beyond the caps, or else by placing beads on either end of the shaft that holds the bobbin.  Narrow slots make this problem much worse. 

If I had to pick only 1 shuttle type, I'd go for the biggest leclerc, but my favorite is a 30+ year old one of unknown origin.  Then again, a fiber artist can never have too many shuttles or drop spindles.

 

laurafry

One of the video clips on my You Tube channel shows how I wind paper quills.  

cheers,

Laura

tien (not verified)

I was a fan of Bluster Bay until I tried one of their shuttles with a springy metallic yarn.  Total disaster.  I also find that they are very fussy to thread when using fine yarns (for which you need to thread through more hooks).  I had a set of four BB mini end-feed shuttles, which were wonderful and a joy in the hand, but I gave them up in exchange for a set of Schacht EFS, which are much faster to thread (just lay in the thread) and have not looked back.  I love the outsides of BB shuttles, but I am not a fan of the hook tensioning system.

The Schacht EFS does require an Allen wrench to adjust, but I hang mine from a little hole drilled in my loom (a tool space that came with the loom) so it's always ready to hand.

Barbara Keyser (not verified)

I prefer my Boat shuttles - wood only - the plastic doesn't move smoothly over the warp.  I have 2 sizes of single shuttles & a double one I picked up to do 2 colors - all work great. I got a hand crank bobbin winder & it works well.  No need for power for me, but others using finer yarns may prefer the power ones or that modified drill idea.  Weavers are so clever! 

thelmaweaves

My favorite shuttles are Schacht boat (open bottom) and Schacht EFS.  I have others but I always end up using my Schachts.  I like the feel and the weight, it's always just right.

Sharon

marlenedg (not verified)

 A cordless drill was part of my Christmas present from DH this last year along with a compleat tool set. I thought at the time,why do I need all that, I can just go outto you shop and get what I need. Then I got my loom. I have used most everything in that took kit but the drill is the best. I put a wood stick with some tape wrapped around it in the drill and just slide the plastic bobbins on. Set the thread on the spool holder and wind away. Only problem I have is not enough bobbins cause I get so carried away winding bobbins I fill them all up. I bought plastic ones for 99 cents instead of making paper ones. Next time I get back to the weaving store I am buying more. So fun to fill!

Marlene

sequel (not verified)

A double ended bobbin winder will wind up just about anything, from the tiny quills for damask shuttles to any size bobbin or pirn.  Mine is a manual one from Schacht.

A shuttle all depends... if it's too light, it may lack momentum needed for wide warps.  If the tips on low profile shuttles are too low, they may pick up warps from the lower shed on the way through, especially if you have a slack lower warp, sometimes a problem on LeClerc looms

If you use a shuttle with an oval bobbin cavity, like Schacht, you'll need Schacht style bobbins with extra collars at the ends.  Use LeClerc bobbins ("flat" ends), with LeClerc shuttles (rectangular cavity).

On the other hand, if you have a narrow warp and your bobbin unspools too fast, a collar type bobbin in a rectangular cavity shuttle will slow down the unspooling...

 

 

 

mneligh

You can also wind bobbins on the spindle of a great (walking) wheel.  I wonder why I haven't seen bobbin winder attachments from the big  treadle wheel manufacturers . . . It would really help at crafts fairs and re-enactments.

MorganAdcock

Does anybody know of any web retailers which not only carry Bluster Bay shuttles but allow you to see the actual shuttles for sale.  I get totally turned off by the "let us choose" method of picking a premium wood (or pretty much anything else).  It's all subjective, and that's not an option I'm willing to use.

Submitted by Anonymous (not verified) on