Now I'm moving onto a four shaft loom, and using some fairly fine yarn, I was thinking of buying a reed/sleying hook, but the only ones I can find (UK) are too thick for most of my reeds. I figure I'll cut some plastic folder or book cover and make my own, but I was wondering what does everyone else do? And what was used in the days before plastics, anyone know?

Comments

ReedGuy

Thinly sanded wood was used sometimes. I use card stock doubled and put tape on the edges. Been working fine so far. One doesn't always have to buy all the time. ;)

Dawn McCarthy

You can use a heddle hook to sley a reed, they are quite slim and work really well.

Dawn

Bewove

 

kerstinfroberg

also, there is some "give" in the middle of the reed. Nearly no hook I have can be used near he top/bottom - esp not if there is yarn involved, too :-)

Woodburner

Thank you Kerstin. :)

I had tried my heddle hook on a fine reed before, and it was clearly too thick . . . ahem! . . . I never thought of trying to move the reed bars to one side! I just assumed they didn't move. lol

Thanks all. :)

ReedGuy

I do that all the time in my 8 dent reed and my wooden 1/8" thick reed hook. :)

debmcclintock

An old butter knife with a slit sawed and sanded works nicely. However I think a heddle hook might be easier to obtain.

Bonnie Inouye (not verified)

Have you tried a reed hook? If your weaving class did not mention this handy tool, a quick online search brings up photos. They are inexpensive and effective with reeds up to around 16 dents per inch, with some variation in thickness from one brand to another. I prefer to have at least 2 warp ends per dent, so I have not needed anything finer than 16.

A reed hook is shorter than a heddle hook and broader when viewed from the side. It is much easier to sley with a reed hook than it is with a heddle hook.

Bonnie Inouye

Yvonne K

My reed hook came with an old loom and it had been cut from a sheet of copper. It is both fine and stiff.

MaryMartha

There is a flat brass tool on the market with a heddle hook on one end and a reed hook on the other, about 1/16".  I have had no trouble with up to a 16 dent reed (in the middle).  Halcyon carried them, and so does the Mannings and other outlets.  Not to promote any one source, but here is a convenient picture from the halcyon catalog.

For some reason, I think these were originated by Harrisville?

Yvonne K

My reed hook is brass, not copper. Copper would be too soft.

Weeweaver (not verified)

And I have made several from laundry detergent bottles. Find one with a longish straight side and just cut one or more out with scissors. They work great and if you misplace or the dog eats it, cut another!

Catweaver

I'm interested you say 'I prefer to have at least 2 warp ends per dent'. I usually have 2 or more ends per dent but that is because I only have a 10 and a 12 reed and I like weaving finer cloth, rather than any conscious preference. Could you explain your reasons, please?

sally orgren

1) You can pinch the yarn to fold it, and pass it through the dent. Some folks are very fast using just their hands. (Not me, but some folks!)

2) Bend a long piece of wire in half. Use this tool like a needle threader. Poke the loop of wire through the dent, poke the threads through the wire loop, and then pull the wire back through the dent with the threads. (This idea from Jason Collinwood.)

How fine of a dent are you looking at? (I sley 15 regularly with 2 per dent, but my finest reed is a 20 epi.) For these reeds, I use my heddle hook as it is thinner than my reed hook, and I have one that is not too long.

And I always sley near the center of the reed (center as in from top-to-bottom) because the dents flex more at that point, as Kersten pointed out.

Hope you are happily sleying soon! Now, if only there was a tool for helping us avoid errors when sleying irregular denting orders, like 2,2,3. ;-)

Bonnie Inouye (not verified)

It saves time to sley 2 per dent. I think it places less stress on the threads. Any little thicker places or knots with slip through a wider opening. I use 4 per dent in a 12-dent reed and haven't had problems; any reed marks disappear when the cloth is washed.

Bonnie Inouye

Joanne Hall

Hi Sally,

Your number two suggestion is a description of a tool we send with each loom we sell.   We call it a threader for the rigid heddle loom and a cord threader for the floor looms.  It is great for pulling Texsolv cord through holes in the loom parts.  The wire loop is secured into a wooden handle and it works very well for sleying fine reeds.

Joanne

Woodburner

Thanks to debmcclintock's idea of adapting a butterknife, I now have the perfect tool. :) My Mum has a pair of old butter/cheese knives. They already have a hook on the back! The thin blade passes easily between the wires of a 25dpi reed, so one of them has now been transfered to my weaving toolbox. :D

sally orgren

I was helping a guildmate warp her loom. She had both a regular heddle hook and the Halcyon brass tool. Since she was on a table loom with limited space inside the castle, I suggested she use the Halcon tool as it was far shorter than her heddle hook. So the right tool might also depend on which loom you are threading! I would not have thought of that prior to following this conversation.

MaryMartha

And I have that cord threader Joanne mentioned, but hadn't considered using it in the reed.  Also, Sally, your #1 is a viable option for threading texsolv heddles.

-- All the requisite equipment, but still so much to learn.

Mary 

debmcclintock

Yeah for mum's extra knives! I learned that from some Lao equipment makers that were prethreading a very high epi bamboo delicate reed with a dummy warp and that is what they used. Nice handle for your grip and a thin tool for the fine dents.
Submitted by Woodburner on