Been trying to understand reading drafts and thought I had a handle on things and then I run into this draft (http://www.leclerclooms.com/pattern/2012/Novembre/Anglais.htm).  Does anyone know a good resource that I can get that would help me understand how to read this? 

Comments

Sara von Tresckow

This is a standard format for an overshot draft. The same conventions are used in Davison's "Handweavers Pattern Book".

To understand how to set up and weave this project, some understanding of overshot as a supplementary weft technique is needed - this information should be in just about every basic comprehensive weaving book. 

A draft is shorthand for how to make a particular structure of fabric - the draft assumes that the weaver is also familiar with this structure.

mrdubyah (not verified)

     Not sure what you need help with, but this is an overshot pattern.  That means you have to throw a tabby (aka plain-weave) pick with the white yarn after every pattern pick with the blue yarn.  You'll need two shuttles.  Throw a pattern shot (blue), then a right tabby (white), then another pattern shot (blue), then a left tabby (white) and so on.

     The top part is the threading.  It shows which frame of a four-frame loom to put each warp thread into.  Read it from right to left.  Each x indicates a thread and its position indicates which frame to thread.  This says warp thread one goes through a heddle on frame 1, then warp thread two goes onto frame 2, three into 3, four into 4, and five will go back into frame 1 again etc.  When you come to the end of the top drawing, move to the right side of the next drawing down (starts with 3,4,3,2,3) and keep reading right to left. Repeat until you come to the part marked "centre".  This part (indicated by the long vertical lines) consists of 30 threads, but you have to repeat that threading six times so that you have threaded a total of 180 threads with the "centre" pattern.  Then keep going right to left through the rest of the threading. 

     The next part of the drawing shows the tie-ups, i.e. which treadles tie to which frames.  This drawing assumes you have six treadles and ties two frames to each treadle, with the first two tied up tabby (1+3 and 2+4) and the rest tied up in a 2/2 twill (1+4, 1+2, 2+3, and 3+4).  Ignore the line that says "tabby", it's just there to tell you where the tabby picks are. 

     The final part of the drawing shows the treadling order.  The numbers indicate which treadle to push down for each pattern pick.  Note that the tabby picks have been omitted for simplification.  Reading from the top down you'll weave 4 (tabby), 2 (tabby),3 (tabby),2 (tabby) etc.  This will make the top border of the runner.  When you get to the part marked "centre" just keep repeating that part to make the runner as long as you want.  When it's long enough, weave the part marked "end of centre" and then weave backwards (up) from the asterisk* to the beginning of the pattern.  This will make the bottom frame as a mirror image of the top frame.  Voila!  

ReedGuy

A book I would have is 'Weaving Overshot: Redesigning the Tradition', by Donna Sullivan. It may be hard to buy new, I think it's out of print.

It's overshot, so the ground cloth (warp and weft) is tabby or plain weave which is woven on treadles 5 and 6 with the 16/2 cotton as the warp and background weft. That is the function of the thinner yarn, is to make plain weave cloth. The patterning (and half toning) is with the 8/2 cotton. So how it is treadled, is treadle 5 is tromped for the first shot of tabby weft from one shuttle, then followed by threadle 4 with the pattern weft from a second shuttle, then tromp 6 for another tabby shot, then tromp 2 for the pattern weft. Your going back and forth from tabby to pattern. The draft is written to be threaded starting from the top row on the right and moving left. Some sections of the threading indicate they are repeated. The treadling begins from the top under the tie-up and goes down the page. They have not shown the tabby pics in the treadle sequence, because the draft would be elongated. In software like WeaveDesign (free) I double the weft picks so it displays square on screen with the tabby ground picks included. So a sett of 30 epi in the warp, I set the weft ppi to 60 in WeaveDesign. But actually what happens in overshot is the pattern wefts float over the tabby cloth, and in many drafts much longer floats are on the back side. Some drafts are designed to be actually good on both sides. Overshot can use very big drafts and may incorporate elements (blocks) from many well known patterns which can be varied simply by modifying the treadling sequence in certain areas of the woven cloth. Like borders and headers and such.

Once you have a good handle on reading drafts in general, this will be a breeze, but takes much attention and rather slow weaving.

A lot of overshot patterns are written for jack looms. So, if you have a counterbalance or countermarch loom the pattern will be on the underside unless you change the tie-ups from rising to sinking. So on a jack the O's rise, tie it so it falls on a counterbalance-marche loom.

Information overload, others got ahead of me. :)

sally orgren

is there is no language barrier. So once you learn how to read them and "see" what is there, you can look at drafts from many different countries, understand the pattern and how to weave it!

mrdubyah (not verified)

On the contrary ReedGuy, I think you contributed a very concise explanation, more so than my own.  Well said.  The only thing I would note is that, in this particular draft, the tie-up shows the tabby on treadles 1 and 2 instead of 5 and 6.   

ReedGuy

I number mine from the opposite direction, we are talking the same treadles. ;) I also number my shafts from the back to the front, one at the back. And in the draft, 1 is the top row of cells in the threading for me. It's like I'm looking down from above. I make my drafts so I am treadling from bottom to top. And really doesn't matter because you end up with the same cloth in either direction. ;)

Submitted by mjcallsr on