As I check out drafts online, I see quite a few that have two rows that seem to use the same treadle.  Wouldn't the second row on the same treadle just unweave?  I imagine the solution to this is simple, and staring me right in the face.  But since I'm entirely youtube instructed, I'm guessing there are some gaps I need to fill.  This article discusses the fact that you *obviously* have to start and end with tabby weave.  But how is this accomplished on a patterned treadling?  I'm confused.http://weavermania.blogspot.com/2008/10/bubbles-bobbles-and-bright-beautiful.html  Thank you in advance for any help!

Comments

pammersw

If you have a floating selvage or go around an end thread at the edge it's ok. But I think "tabby" is the answer to your question in this case - something that as a new weaver, I haven't quite understood conceptually yet. It's something like an every-other-row plain weave, not shown on the chart, that holds stuff together. Figuring it out, and doing a sample of one, is on my to do list.

laurafry

Yes, it would depend on the weave structure.  An overshot is often just written out with only the pattern sheds shown in the treadling, generally with a notation to 'use tabby'.  Plain weave is any combination of shafts which will give you plain weave.  Not all weave structure are the same!  

Overshot is a type of 'twill variation' (as one way to describe it) and generally plain weave results in tieing up shaft 1 and 3 on one treadle, shafts 2 and 4 on a second treadle.

Bronson Lace otoh, needs (again generally, it depends on how the warp has been threaded) shaft 1 on one treadle with all the rest on the second treadle.

Summer and Winter - again threaded differently from either of the above - is generally shafts 1 and 2 on one treadle and all the rest on the other treadle.

So, the answer is - it depends!

cheers,

Laura

JuliannaHeiby

All directions to look into, thanks!  What I have currently on the loom shouldn't be needing that resolved, but I'm glad to know, because I've been avoiding drafts that have this "unweaving problem."  What sort of loom are you learning on, Pam?  I have a handmade, craigslist-found 24in 4h/6t floor loom.  It's a little... quirky!  But we are relating well to one another so far ;)

JuliannaHeiby

So, are you saying that the warp ends that form the selvedge on each side should follow a different threading pattern than the rest of the fabric?  I don't understand how you can start and end with tabby, if you're following a different pattern.

macontavern

I too am new to weaving but will try to explain how it was explained to me and made sense.... weave the first pick of the weft, then weave 1/2 plain weave (1/3), weave the second pick of the weft (what you are calling the unweave), and then weave the second 1/2 of the plain weave (2/4), weave the third pick of the weft, 1/2 plain weave (1/3), weave fourth pick of the weft, then second 1/2 of plain weave (2/4). the 1/2 of the plain weaves lock the picks in place and unweaving does not occur. I have not done a tabby yet but it made sense to me when it was explained this way. Hope it helps.

pammersw

The threading at the edges can be different,  and is in the draft you linked to.

My weaving lessons were in a 4 shaft Leclerc Voyageur table loom. I've rented a 4 shaft, 6 treadle Baby Wolf from the guild for about four months. I seriously want a loom of my own!

I've done a lot of plain weave so far, and some simple twills - so there is a lot I don't know yet! :)

ReedGuy

The draft as shown won't make that pattern. There are circles, but there are no diagonal lines anywhere in the original. If you look close at those photos you see a much finer 'purple' tencel weft thread used for the tabby picks. In the original draft the tabby treadles are on 1 and 2, far left. That is why you see checkering when treadles 1 and 2 move shafts 1 and 2.

Submitted by JuliannaHeiby on