Ok, so I read Steve's wonderful description of how to direct warp the log cabin pattern and was thrilled he added it to the choices.  Now, I discovered that I was doing it ALL wrong.  Instead of separating my darks and lights from the pairs they were in when I wound the warp, I had threaded them in alternating pairs.  Here's the picture, my explanation stinks.

And, I was weaving the same way and knew it looked wrong.  So, I took the whole thing apart and rethreaded and tied on, spread the warp and began weaving again. 

Now, I have this:

The contrast of the taupe and dark blue is not sufficient to show the log cabin pattern.  Plus, although they are the same weight in yards per pound (ypp), the taupe yarn is round and chained and the blue is a thin worsted. 

The photo is fuzzy but I think it you can see what I mean about the difference in the yarns.

Now, I need help figuring out what to do,  I want to rewarp the entire project and somehow keep the navy warp and replace the taupe with a white wool yarn that is close in weight to the navy and will add more contrast.  The only way I can figure out how to do this is to direct warp the white onto a large dowel which will act as a second back beam and I can hang it from the back of the loom.  Sort of the warp weighted idea.  Then, I would replace the taupe in the threading as I wind the warp, put it on this 2nd beam and beam it separately over the navy warp which is already tensioned nicely on the existing back beam.

Or, do I scrap the entire project, save the yarn (which was all free at a yarn swap) and start all over again.

I need some advice and ideas. 

Claudia, totally bummed and a little embarrassed.

 

 

Comments

francorios (not verified)

Those look like neat yarns.

I think you could re-thread the heddle in the manner described by Steve to correct the pattern for weaving without having to take any yarn off the beam.

When you start weaving, be sure you straighten out any crossed threads on the back beam every time you advance the cloth.

Have a good day!

claudia (not verified)

Ok, I gave in.  I rethreaded everything, a second time, and wove it, a second time.  It looked awful.  I couldn't even bear to take pictures.  I took out the warping peg, found a white yarn that is very similar to the dark blue and, with the warp on the back beam I "direct" warped the new yarn. 

I took one taupe yarn out and replaced it with the white, walked back to the peg, wound it around and came back and replace the next taupe thread.  It took about an hour.  Then, I wound the entire warp onto the front beam, cut the taupe yarn off the back beam.  Retied the navy and white yarn to the back beam and, with the help from a friend, wound the warp back onto the back beam with paper between the layers.  Now, I am retensioning the yarn on the front apron rod, or whatever it's called, and then I'll weave for the third time.

Hopefully, since I am into cliches lately, the third time will be the charm.  Ugh.  This was not in the plans but now, at least, it is done.  The warp looks better and I hope the results are improved.  Pictures to follow soon.

Claudia

claudia (not verified)

Here it is.  Attempt #3, not sure I am on the right track yet. 

HELP!  I have done this at least 6 times before on my 4-shaft loom and it looked great.  I just don't see where I have gone astray here.  I must be missing something.

log cabin experiment

so, I am following "tromp as writ" weaving the same as I threaded.

D-L-D-L  L-D-L-D  D-L-D-L  L-D-L-D

    A              B            A            B

But the blocks do not show up as nicely as they do on Franco's piece.

Perhaps I should double the weaving and do this:

D-D-L-L-D-D-L-L      L-L-D-D-L-L-D-D-

           A                              B

I'm open to suggestions and ideas.  Clearly, this is not producing the web I expected.

Claudia

Submitted by Anonymous (not verified) on