I have decided to put my loom into working order. I have it strung up again and seems to be in working correctly. I replaced the #16 reed with a #10 and have it tied up for tabby on each side and twill in the center. But I am rethinking my first impulse, which was to weave the rug as wide as the reed, which is 43". I think what I want is a large rug, but one I can take out and shake.  I bought 8/4 cotton warp and my weft is strips I cut from grandmother's double knit slacks. I think this is going to be heavy so was hoping some more experienced rug weavers might have suggestions for a nice sized rug. I have a large capacity washer and it would be nice if it were washable, too, as it will probably be a kitchen rug.

You may have guessed by now that I don't know what I'm doing, so any suggestions will be received gratefully!

Comments

Little Meadows (not verified)

It seems that many rag rug weavers like to do rugs at about 28" wide, that's what I do too since it seems a good size at the kitchen sink - I can move in and out and stay on the rug..  I can shake a rug 28X40 and it fits a regular top load washer just fine - tho I wash 2 at a time for balance issues.  Of course if you need that width you could always drape the rug over a railing and beat it - while thinking pleasant thoughts :).  Liese

Sara von Tresckow

 I usually weave rugs reeded about 30" which gives you 28-29" off the loom.

When I have woven wider, it is difficult to find a place for them as many hallways and narrow places in the home are 3 ft. (36") wide and rugs that near that measurement don't lie well, or look nice.

HazelRose (not verified)

Thank you, ladies. Those are all good points. I think I'll take your advice. My kitchen is rather long and narrow so that width would probably be better, anyway.  I don't really want wall to wall, now that I think about that. lol DH goes to town tomorrow so I'll have the day to myself and I think I'll start  measuring the warp. X your fingers for me!

Hazel

HazelRose (not verified)

One more question, please.

I was thinking I could warp up for two rugs, I know this is done for towels at least. So I think I would double the calculations for one rug and add...what?  a foot, a yard, extra to separate them? Would this be practical or are there problems I'm not aware of? I have plenty of warp string.

I have the Rag Rug Handbook and they talk of removing the rugs from the looms but I can find nothing about warping for more than one.

I have my warp, my warping board, & my initial caculations ready to go....

Sara von Tresckow

 Since rugs are usually done with simple threading and all the same width, rug weavers put on LOTS of warp at a time. You calculate what goes between by figuring how much you want for fringes (remember that braided they shorten up a bit) or for sewing back in, double that and add a bit for a fudge factor.

If you are just starting off, put plenty of warp on in case something happens on the way to completion.

I generally put 10 to 12 yards on my rug loom, weave two or three, cut off and let it sit until I have an inspiration or the necessary yarn for some more. As rugs cause considerable buildup on the cloth beam 3 or 4 would be the max before you should cut off anyway.

HazelRose (not verified)

I don't like fringes, so I figured 3" for a hem. I probably ought to make that 4, doubled to 8 so... maybe I ought to add a foot in. That should do two hems and allow for operator error, if I understand what you're saying.

claudia (not verified)

Hi Hazel,

You might want to try our weaving calculator to figure out the length of your warp for the rug project.  One added plus is that you can print your calculations and you will get just the Weavolution header and you calculation sheet, no ads, no junk.  Plus, if you want to weave 2 or 3 rugs at the same time it allows you to put in the number of "pieces" you plan to weave.  The calculator will give you both warp and weft AND cost.

Go to the "Resources" tab and click on Weaving calculator.  Let me know if you want a hand with it.  It's great but very complex and the first time through can be a little rough.  It took me a few extra minutes to get it.

Claudia

HazelRose (not verified)

Thanks, Claudia, I filled in the numbers I knew but could not find any buttons to push to make it work so went back to the old fashioned way.  But actually I had just finished measuring the warp when I found your post. I will take another look at the calculator, tho, as I have lots of rags to weave up. And lots of yarns. Once I get this thing going I will be a weaving maniac! lol

HazelRose (not verified)

Where I am.   Just thought I'd let you know that i am weaving.  I have about 28 Inches done on the first rug and it is an excellent sampler of what can go wrong with a project! lol The first thing that went wrong was that I had cut my strips too wide so had to recut them all. The selvages are rather free form. I found that there is something wrong with my threading that stands out in tabby but is less noticeable in twill so that is what I am weaving now. I could not figure out what I did wrong so  just left it alone and decided to give my attention to getting straight edges and consistent beating.  It will not be an entry in the state fair, but it will look just great on my kitchen floor and I am already planning my next ones! I want to try my hand at towels, too.

I have had to work in the loom shop this week so have not been able to weave but I might sneak off and spend a a couple hours with it today. I'm anxious to get it finished! And I thank you ladies for your help and encouragement in finally getting started on this project!

 

whorlwindweaver (not verified)

Sounds like you are having fun. I'm glad you found the twill is working out.  Who know what happen sometimes when threading.   I'm in the process of having a disaster trying to weave towels. For one thing I mysteriously ran out of heddle on one shaft when mathematically there should have been too many.  Also, I forgot to leave the lease sticks in and the rest is well, complicated.  I'm trying them over again.  argh.  I've started talking about it on my blog and I think it may be a saga. 

I think I'm going to warp my big loom for some rugs so I can step away from that crazy project. .  I like to spin the yarn instead of using rags, but I think when I get enough old blue jeans it will be time for some recycling.

I suppose I could use old t-shirts, but I use them for cleaning, plus they are all white right now.  haven't tried rags yet but I know I will.

whorlwindweaver (not verified)

Uhoh, and I was planning to make some 36" rugs.  Well, i'm new so if they are all crazy it won't be unexpected. Plus, two are going in the bedroom, except the one I want to put in the living room.

yet another noble experiment...

HazelRose (not verified)

Yes, it all very mysterious to me so far. I'm figuring out some things but even so... Still it is fun and I'll get a rung in some form and I expect the next one to be a little better and the next one...etc. I say bath mats woven of old white t's which is what I have planned for mine. Another in a loooong list of ideas for projects!

One of the things I need to study up on, I think , is the use of lease sticks. Somehow I have missed that part and I'm thinking their use might eliminate some of the problems I have in getting the warp on at a more even tension. But in spite of it all I'm forging ahead! Good luck with yours! I'm off to read your blog.

whorlwindweaver (not verified)

I think we are supposed to leave the lease sticks in, but winding on with them is kind of tricky.  I post every Sunday, and the next one will have a picture of how lease sticks can be put on a counterbalance loom. I'm using Cynthia Weld's book to help me learn.

I think I finally got  the contraption figured out and the lease sticks set up so they don't wreck the warp.  It took me a while.  I had an earlier version that wrecked lots of warps, but the one shown appears to work fairly well--it has to be watched while winding on though. 

Are there any experience weavers who can shed light on this lease stick thing? 

Sara von Tresckow

 Lease sticks are easy to use.

Just make sure you tie them together at the ends with string - make it an "x" so your warp threads can't fall off. You do that by dropping the tie cord through the same side of each stick - that forms a little cross that holds your warp threads even if the sticks tip on end inadvertantly.

Then use those string ties, run a long cord through them and tie them down with a quick release knot wherever it makes sense at the time - you can move them around your loom several times while warping.

Yes, leave them in and tie them to the back beam to keep them there during weaving. You don't need any special diagrams, devices, wonder methods, etc.

Laila Lundell's "Big Bok of Weaving" shows their use in several places.

whorlwindweaver (not verified)

Thank you!  As a new weaver, I have already forgotten to leave them in twice.

Is there any trick to winding on warp while they are on.  I add lots of trouble with everything getting snarled. Of course it was the first time I tried it.

Sara von Tresckow

 To avoid tangles, simply tie the lease sticks to each side of the loom during warping - leaving enough play that you can move them where you like, but not enough to let them flop to one side or the other.

After a time or two you'll find what works on your loom.

HazelRose (not verified)

I have not made much progress in this last couple weeks. I got a bug of some kind (My doc assured me that it could have even been caused by "meanness"! lol) But whatever it was I have now recovered. Had company last week but they are gone now, too and I hope to get back to my rug weaving this week.  I am going to try to post a photo of my progress so far. I have made a little progress. I was showing it off to my sister this week and seeing it with 'fresh' eyes I found many more ...er... "design elements" that I had not noticed before. Oh well, I guess it just gives me more to aim for in my next one.

rag rug

 

suzyhok (not verified)

This looks really great on the loom.  I love the colors that you've picked.  Your grandma had a nice sense of color!

As for your "design elements" -- can you tell where you have skipped a dent or double sleyed by raising the different shafts (harnesses) and seeing if they are evenly dented.

HazelRose (not verified)

Thank you. No, I haven't been able to figure out what I did but it's not really obvious as I weave do decided to just let well enough alone, as the saying goes. I have since finished the first rug and am about half way though the second one. I should be able to finish it this month. I hope so because I may be buying another, and smaller loom.

suzyhok (not verified)

You go girl!  That's great that your 1st rug is finished and you are well on your way on your 2nd.  Make you take photos and share your finished projects with us!

What is your new loom?  What do you plan to weave on it?

HazelRose (not verified)

Well, ladies, I finally finished the rugs!  www.weavolution.com/node/5975  I posted photos in my projects file. They are not a shinning example of the weavers art but I like them.

But now it's getting to be cold out and there's no heat in the loom room so, to tide me over the winter i bought a used Baby Wolf loom that actually fits in my house! I have had it two weeks now but would not start playing with it until I finished the rugs.

I just got the HandWoven magazine and I think I am going to attempt the place mats on the article by Susie Liles.

But I have not forsaken my little looms. I just made a coffee pot cozy for the camper trailer. We recently camped at a couple Nat'l Parks where there is no electricity and my old Pyrex coffee pot works great still but does not keep it warm. I think my felted wool cozy will do the trick. Sis asked why i did not just pour it into a thermos. What a wet blanket! lol

kds1679 (not verified)

Just found this site and this is the first thing I've really read. It's great!!! I am loving it. I belong to a very small guild and almost everyone else is way ahead of me in experience and knowledge. It is so refreshing to learn of other's "design elements", "free form selvages", and stumbling ahead anyway. Thank you. I needed that. I haven't woven a lot of things yet, not that I haven't wanted to. Life just like to throw in a few curve balls to keep us on our toes.

Right now I am in the planning stages for a rag rug that will be going in my GR GR Grandfather's cabin that is part of a ghost town that is being restored. Several of his descendants have sent me wool fabric to use in it and everyone is very excited for it. It has already taken far too long and I think people are beginning to wonder if it will ever really happen. I was too, but I now have most of the stumbling blocks sorted out and I am ready to get it done.

Does anyone have a suggestion for a draft that would make a nice durable rug, but that would also be quick and simple. I have a 45", four harness loom. I think they were wanting to put it under the table, which means it would need to be wider than my loom.

Any suggestions would be greatly appreciated. Thanks

HazelRose (not verified)

I bought the Rag Rug Handbook by Janet Meany. Lots of good information and projects there. I have not made a large rug yet but I beileve they are woven in strips and sewn together. Your project sounds like fun and also worthwhile. It will be exciting to see it finished and in your great grandfather's cabin.

HazelRose (not verified)

I think the loom has found a home. I'll know for sure tomorrow.  I have a large Cambridge Rug loom, made by the Reed loom company. It has been refinished nicely and has flat steel heddles. I have woven several rugs and some upholstery yardage on this loom but I have lost my loom room and must move. I hope to find a good home for this loom but you must pick it up here in Northern California. Did I say it is free? That’s how I got it so will pass it on the same way. I wish I could keep it but it’s not to be.
I also have a stock of rags that I have been keeping for this purpose that could go with the loom. I will try to get pictures and the exact measurement of the weaving width, which I believe is 43 inches.
If you are interested or know someone who might be able to use this loom, please contact me ASAP as I have to move it by the end of September.

Kristiek1

I'm starting my first "hit and miss" rag rug and want to make it approx. 32" wide finished and 72" long.  I have a pile of rags cut up out of old jeans and slacks.  The strips are only about 24" long so I asume I will need to sew them together.  Question is....how long should I make each strip?. Do I just sew a bunch of colors together end to end or make individual strips all one color?.  I think I'm making this harder than it should be but I just can't seem to to figure it out.  Also, do I put 2 strips together to be sure the rug is thick enough?  Also, if I have fabric that is lighter on one side than the other. Can I just put 2 srips together with the good side out and just lay it in the loom and beat it or do I have to sew them together?  Thanks in advance to anyone that can help.  Oh, also, can I use a 5 dent reed for this?  The only other reed I have is a 12 dent that I use for warp faced rugs.

Joanne Hall

If you have not made your rug warp yet, make it a little longer for a sample.  First weave a small rug, maybe two feet long.  Make this rug using the cut rags singly. Cut it off and then evaluate what you did.  Put it on the floor and determine if it is thick enough and looks like you want it to look.  Weaving this first small rug and evaluating it will give you answers to all your questions. 

I would use the 12 dent reed, sett the warp at 8 epi and use a temple.  I would use 12/6 seine twine, which is very strong and would not need to be doubled.

Joanne

 

Submitted by Anonymous (not verified) on