I'm sure there's a rule of thumb, but I can't seem to find it.   I have a project I'd like to do that is 36" on the loom.  My loom is 36".  Can I do it at that width or am I supposed to make my projects slightly smaller than the reed?

Thanks in advance.

Comments

Dena (not verified)

While I generally prefer to work smaller than the full width of my loom, there is no reason you can't do it.  Go for it!

louiseinoz

It's the width of the reed that will determine how wide your project will be.  Measure the width of the reed and even the number of spaces before you start.  You can always dent the edges a little tighter and it usually helps the sevedges. If you don't know how many spaces you've got and you sley all the way across and end up with 8 or 10 ends (that you really need to match the pattern) left over and no more spaces in the reed, you just have to sley it all over again - ask me how I know

The time you spend checking everything out carefully before you start won't be wasted 

DebD (not verified)

thanks.  I doubled checked the width of the reed and it's enough.  Thanks for the tip about denting the edges a little tighter if need be.

loomroomcat (not verified)

It is the width of the harness frame that determines your maximum weaving width.  Your reed could be wider than your harnesses, but I would not weave wider than the harness frame. 

ReedGuy

My harness is the full width of the loom, the shafts are open ended without end frames. My rollers are 1/4" on shorter than the loom frame, this is because the roller has to roll free with a little "wiggle room" at the ends. So really, the width of the roller and the loom frame limit your weaving width. I can weave 62", but I buy 60" reeds, that are probably 62" but you loose width because of the end bars that hole it together. I could buy a 66" long reed for my beater, but wouldn't gain me anything beyond the 62" of the loom frame. :)

Weavejoyforall

   I'm new to RH weaving. and new to my Brand spanking new Kromski harp 24.  I am thinking of warping my loom for two scarfs about 2 yards each how much warp waste should I plan on?  Oh yes I want at least 4 inchs of warp for each scarf for fringe at each end.  anyone have a good way to figure my total warp length? will 4.5 yards be enough or do I need much more?

endorph

I have found my warp waste to be minimal - Part of you back loom waste will be the fringe on your second scarf. Depending on how you tie on the front, that waste will figure in as part of the fringe of your first scarf. You will probably end up with only five or six inches of actual waste on the warp - if even that. Does your 2 yds length include the fringe or is the fringe extra? I would probably at 4.75 or 5 yds to be safe. If you are looking at 4 yds for the two scares and an additional 16 inches for fringe (4 inches at each end) that is 4 yds 16 inches - or nearly 4.5 yds - you need to add some extra length for the loom waste and you will want to have your unfinished fringe at about 5 inches in length for a finished length of 4 inches. This is your math problem for the day :)

sandra.eberhar…

The width of the piece you can make on a loom is determined by the narrowest component.  I have a loom with a 48" reed, 48" shafts, but the cloth beam is 42".  I can weave a 42" piece on this loom.

SallyE (not verified)

If you are going to weave at the full width of the loom, make sure to count out your heddles before you start threading.   If you have a lot of extras on one or more of the shafts, you should remove them or they could prevent you from working at full width.   This is especially true if you have metal heddles.   The extras take up some space and will abrade your warp if space is tight and you leave them in place.

 

 

Submitted by Anonymous (not verified) on