Hello good people

I'm new to this forum, though I created an account years ago before I went off to college when the site had just started up, but I never actually used it

 

Anyway, here's my question. It's summer holidays just now, and as I've got space to set up my loom I decided to make scarves with some leftover cashmere I got free off my old work (a small knitwear/accessories firm). But then my mother was clearing out the attic and found 5 boxes full of wool I'd completely forgotten I had, that I got given years ago (again, before i went to college) so now there's this huge amount of wool I have to use up, on top of the cashmere and the fine wool and the linen and all the random unidentified stuff. So I figure I'll make curtains.

 

So I'll be making big wide yardage of cloth (I'm going to do double plainweave so I can get maximum width out of my 4-shaft loom)

 

And because I'm making big yardage of cloth and there isn't a finishing mill anywhere near here at all, then I decided I'm going to have a go at actually finishing the cloth in the old way. So, I guess, treading the cloth in the bath or the river or something, and then tentering out in a field or at the beach or something, I haven't really figured that bit out yet. I'm going to need a huge amount of marquee pegs for a start

 

So, has anyone done this before? hand (or foot) finished and/or tentered large yardage of cloth (or even small yardage, i'm not picky)

 

Here's my thoughts.

 

Firstly, I've hand-finished small pieces of worsted cloth before, machine soap and hot water in the sink, so I figure I'll just do that but with a bath and more so. Here's a thing: does the water have to remain warm? is that an issue? I sure hope not

 

Secondly, with the tentering, all I've really got to go on is descriptions and pictures from old books and a description of the modern industrial process I got from college.

 

I really have no idea

 

-Andrew

Comments

laurafry

Hi Andrew,

Yes, you can do large pieces in the bathtub.  Do remember that fully saturated wool can be *very* heavy!  Since you're doing curtains, what you might find is that cutting the yardage apart into panels slightly longer than you need and doing each panel separately will be physically easier.  Plus you only need space to tenter each panel, not the whole length of yardage.

Are you planning on fulling or doing a worsted finish?

cheers,

Laura

apk5 (not verified)

hi laura. I'm just making yardage the now as I'm away up where my loom is, and I'll be sewing them later on in the year. Need to take measurements and stuff. Will also probably use some of the fabric for to cover my couch and so on. So i don't know exactly what size panels I need. Weight isn't an issue as I'm accustomed to work and I have a wheelbarrow.

As far as the finish goes, I'm not too hot on correct terminology (shame on me) but by fulling I assume you mean breaking it down so's the weave is practically unrecognizeable. I won't be going that far. I'll be weaving in Plain Weave see, so I'll just need to shrink it a bit, say 10-20% to bring it in and thicken it enough that it'll no let the light in and such. I don't want it to be so heavy that it becomes difficult to stitch, as it's quite a heavy count yarn I'm using to weave it with. Don't know the count exactly but I'd estimate 100-120 tex or so.

I expect I'll cut off a piece or two small like for to have a wee practice with before I go for it in earnest.

It'll be some time yet before I do this, so I'm just trying to get my thinking done first, as I'll need a lot of space to tenter it, and also probably a river to wash the clat out with, after it's been treaded.

What would you recommend for tenterhooks? I was thinking of using pieces of wood with nails driven in diagonally so that they're pointing back away from the cloth, though I guess I can use kiltpins for small pieces.

laurafry

Do not underestimate the weight of the whole length of the yardage, fully saturated!  The degree of fulling doesn't matter, it can be a little or a lot, it's still called fulling.  :)  (Although many people these days call extreme fulling "felting".)

You can also use those strips of carpet tacking - don't know what you'd call it over the pond - when a carpet is installed wall to wall the carpet layers install a strip of wood with tiny nails in them to hold the carpet down.  

Ideally you'll want to use something that doesn't rust but if the cloth dries quickly, which it should do out of doors depending on how much humidity you generally have, the strips should work okay.  Ordinary nails might be a bit thick and leave holes in the cloth.  

I'd build a frame of sturdier wood, then attach the carpet strip to the frame.  My dh built me a blanket stretcher by building a frame, then adding another 'free' piece that we clamped to the frame so that we could adjust the width to accomodate different width blankets.  Even though I always made the blankets the same width in the loom, if the fulling went a little further and the shrinkage was greater from blanket to blanket the width would be different each time.  :)

Anyway, do sample the degree of fulling you want for your finished cloth and then use that as a reference while you do the longer piece(s) so you can match it.  And you might want to get some volunteers to help you wrestle the whole length if you decide to *not* cut it in shorter pieces.  It all depends on how long the length you are weaving?

You might try to find a small book called The Final Step by Beverly Gordon for more info on wet finishing wool cloth.

cheers,

Laura

apk5 (not verified)

thanks for the ideas laura, greatly appreciated.

I've sent off for a copy of that book from Amazon, it's a subject I know very little about, we've only really been given a nod to it in college, and it's always about industrial processes anyway, so it's little use.

I've decided to make it up in smaller pieces for to start with. I've made up a warp for to make into throws for the couches, so I'll test out my ideas on those, as they'll be quite small, say 4x6' before shrinkage. I only want enough shrinkage to soften it up a wee bit and take off the harshness of the plain weave. Though this is wool that's been sittin about for quite some time so I really ought to give it a good wash with detergent as well, cos it'll be full of stoor.

Which reminds me, I must buy some dust masks this weekend. I'd forgotten how sensitive I am to stray fibres

Ta

-Andrew

laurafry

Yes, you need to use soap/detergent to scour the spin oil out.  I usually use just enough to get a small 'head' of suds (no more than an inch).  As the soap/detergent binds with the oils the suds will disappear.  When that happens, drain out the water and draw fresh water the same temperature.  Do not let the incoming water fall on the cloth - the pounding of the water can activate the fulling in that spot.

 Add more soap/detergent to continue to scour.  When the suds do *not* completely disappear, the fulling can begin as the oils will have been scoured out.

Run your fingernail across the cloth to judge how stable the cloth is and check it periodically to see how much fulling has happened.  When the cloth is *almost* done, drain the water out (if you haven't done that already - you don't need a lot of water to full, just to have the cloth be fully saturated), rinse and pull the cloth up against the side of the tub.  (Assuming you are doing this by hand or foot in the bathtub)

Let gravity do the work of draining as much of the water out of the cloth as possible, then gently squeeze as much of the excess water out as you can.  Then lay the cloth out flat or pin to your tenter frame to dry.

If I'm going to hard press as part of the finishing (something I suggest you consider as your end product does need to be stable to hang in the window plus it will make the cloth easier to sew) I do that before the cloth is completely dry.

I have video clips on my You Tube channel showing how to full small items and a hard press.

With larger items, like the panels for your curtains, you may want to talk to a dry cleaner who has an industrial steam press and ask them if they know what a hard press is and how much it will cost to press your panels for you.  Doing a hard press using a small hand iron takes an age.  :)

cheers,

Laura

apk5 (not verified)

Thanks a lot for all your advice Laura, I've gotten a lot of good ideas and encouragement here.

I'm going to go for it this weekend. My plans as far as making curtains has changed and now I've used that wool to make fabric for throws. And only a 30' warp, as I don't figure I have enough wool to experiment again with sectional warping, as I had mixed results last time. Anyway, it's best to get practice with using the warping frame in such a way that I don't get it all tight down one side. Which I'm doing by only making sections at a time, like I used to do when my warping frame was nails on the wall.

Anyway, it's all good. I'll let you know how I get on. I shan't be doing a hard press, nobody round here has an industrial steam press and there's no way I'm doing it with a hand-iron. Totally not sustainable.

I'll be following your regular instructions for scouring and fulling. Then I'll be tentering out in the garden, in an exact manner which I haven't completely figured out yet, but I'll see what materials I have available. I'm thinking carpet tacks for hooks, or maybe even just narrow-gauge fencing wire. I'll have to see what there is to use.

 

Andrew

laurafry

Heh - don't blame you for not doing the hard press.  Not really necessary for throws, anyway.  

cheers,

Laura

Submitted by Anonymous (not verified) on