I have short arms.  And legs, of course, but the legs aren't really the problem, the arms are.  I just successfully (YAY!) threaded & tied up my first warp on my new-to-me Varpapuu loom.  As expected, I get a great shed.  My stool (formerly belonged to a drummer) is infinitely adjustable, so I can make it be at the correct height for this loom with a high (36") breast beam and my little homemade counterbalance with a low breast beam (30").  In either case, I can comfortably reach the treadles, so that's fine.

The problem is reaching the beater.  When the beater is returned to its resting position, it's so far away from me that I have to have my belly pressed up against the loom to reach it.  (I have this same problem on my Macomber, which is one of the reasons I don't like it.)  In order to be a comfortable distance for my arms to reach it, the resting position would need to be about 3" closer to the breast beam.

I've certainly seen looms with a handle affixed to the top of the beater bar, presumably to address this issue.  But I'd really much prefer not to do that.  Instead, I'd prefer to put blocks on the castle so that the beater is at rest 3" closer to me.  I've never seen this done, though, and figure there's probably a reason for that.

So what do you all think?  Is this a reasonable modification?  A really bad idea?  Please explain (aka show all your work, if you're in school) so that I understand the implications.  Do you have a better idea?  I know I'm not the only short weaver out here!

Thanks loads!

Comments

Dena (not verified)

There is an adjustment on the Macombers that make it possible to move the breast beam closer to the beater.  Check the metal brackets on the sides of the front of the loom.  There are two positions for where they attach to the metal piece that then attaches to the castle.  And...does sitting higher make any difference?  I weave with my belly pressed up against the front of my loom.  It helps brace me and give me balance.

Joanne Hall

I taught a workshop in Wisconsin where there was a loom like this.  I found that my fingers would catch on the heddles, so we put something on the castle so that the beater would not fall so far back.  This was a beater which is attached to the bottom of the loom.  There is no problem with a hanging beater.  It has positions on the top of the loom so that you can place it closer, and it does not fall so far back.  So, you might look for a hanging beater when you get your next loom.

Joanne

Dawn McCarthy

Peg, I have added giant rubber door wedges or chair stoppers available from the hardware store, the beater then falls back and the stopper sits an additional 1-2 inches from the front of the castle support = 2" closer to your reach!

Dawn

laurafry

Is the beater underslung?  I had a problem with my Leclerc Fanny - the underslung beater fell so far 'backwards' that I kept grabbing the shafts.  Doug put a stopper like Dawn describes on the loom frame that propped the beater forward enough so that isn't an issue now.

cheers,

Laura

Peg.Cherre (not verified)

You've all given me the confidence to do what I needed to do.  I went down to the basement & cut a few pieces of wood.  For the moment I just have them clamped/tied to the castle till I get exactly the correct size, but I can tell you they've made a terrific difference!  Once I have decent looking wood & the correct size & placement, I think I'll use carriage bolts & wing nuts, since that's what's used on most loom pieces.

 

 

 

 

 

Thanks for your encouragement to make my loom work for me.

Peg

Peg.Cherre (not verified)

Yes, Laura, it is an underslung beater.  I've done a block of wood, although I need to work with this size block for a while before I determine if it needs to be even larger (I'm thinking right now that it does).

I know about those adjustments on the Mac, Dena, but they didn't really help me enough.  Not sure why I didn't think about blocks on the Mac, but I never did.  Plus, this is only one of several reasons why I don't really like the Mac.

r1mein54 (not verified)

Thanks for the great ideas, now I can do something better to replace the two spray can tops I have wrapped to my beater with masking tape alot like you have Peg.

Submitted by Anonymous (not verified) on