I'm making a linen warp with Line flax - lea 20/2. I'm using a small mill and notice that in one section between the pegs, i'm seeing and feeling looseness. Do you have ideas on how to handle this fiber when creating your warp. I have 90 threads on the reel, and just noticed it's getting more and more lax. Maybe I should just make small bouts? Any ideas of handling this with better control? I haven't worked with linen much, but remembered having the same issues using a board or mill.

Thanks very much!

Mary

Comments

Karren K. Brito

Humid linen behaves so much better, it is more supple.  For example linen that is on a tube has kinks in it the diameter of the tube, to get those to relax you need to get the linen moist.  Putting it overnight in a plastic sealed bag with a wet wash cloth will do it.   Same with bobbins or pirns.

The same with the warp only it can go both ways.  If the linen has been stored in a damp place long enough to pick up moisture and you are spreading it out in a thin layer in air conditioning (low humidity) it could be drying out.   Or it could be the other way, dry linen picking up humidity from the air.  Anyhow it behaves much better if store it and work with it in the same conditions and humid makes the linen more supple.  I've been known to spritz the linen warp on my loom.  I love linen and have made many warps on a warping board  with no unusual problems.

kerstinfroberg

Can it be that your mill posts are too weak? The warp can easily get tighter during winding (whatever you are winding) - and the in-elasticity of linen will make the differences show more that when using (say) cotton.

Mary Rios (not verified)

 

Karren - I bet you thought I only dyed! Thanks for the suggestions , i wouldn't have thought of the washcloth - humidity may very well have played a roll in this behavior - hadn't thought of that. That said, any tricks for a cone of linen? Or do you suggest i skein it, moisture then reball and wind?

Kerstin - that very well could be  - maybe small bouts are the secret - before the posts start to give in with the binding.

Thanks Ladies!

Mary

 

jennybellairs

Since linen is so strong and doesn't give, your posts could be bowing slightly.  I agree that smaller bouts might prevent some of that, and do all the winding of each bout at one time.  Just start a new one when you first notice the sagging. And of course, wind the warp on the loom under tension with the trapeze.  Have you asked Kati Meek?

Jenny

Sara von Tresckow

Just keep warping using what feels like even tension - don't pull some rounds tighter.

When warping, make sure you leave the lease sticks in to even things out - when you've finished beaming the warp, any uneven length will be at the front where you tie on. And the most important thing - even tension on the beam - will be there.

I'd say you're being too fidgety right now - on a small mill, this is happening all the time, you just don't notice it with yarn that is more elastic. Warping is like being a teen all over again - don't pick at zits. The less you fuss and just get the job done, the better your warp will be.

20/2 is NOT fine linen, nor is it particularly difficult to deal with.

Mary Rios (not verified)

Jenny and Sara, 

Thank you both for taking the time to help me. Jenny, trapeze, of course! (thanks for the reminder!)

I like Sara's description that warping is like a being a teen - I'm plunging forward and hoping for the best! Thanks again all for the words of wisdom.

Mary

Erica J

I know you've received great suggestion so far. I also noticed that the part you're having problems with is a very steep incline that the warp is following. I would also try to adjust your path to have more even slopes. It looks like you have the same mill as I do, you can bring the bottom pegs up closer so you can even out the diagonals. Because linen tends to be sett so close, I usually do no more than 4" of warp at a time.

Good luck,

Erica

Mary Rios (not verified)

Erica - I didn't know that bit about the steep angles - thank you. I swear, it takes a village -!

Mary

weave2 (not verified)

I was always told that since linen is so ungiving, it should be used horizonally when winding a warp.  I usually use a shoe box and dowel.  I poke holes in the box across from each other, and insert the dowel through the holes with the cone on it (the cone sits inside the box supported by the dowel).

I'm sure you'll love working with linen and love the look of it even more.

Alaa 

lkautio (not verified)

I use the horizontal cone/tube trick, too.  However, I use it not because of the inelasticity but to avoid adding twist (which can make the yarn very "lively").

Laurie Autio

Joanne Hall

Hi Mary,

I just returned from the Intermountain weaving conference in Colorado, so I missed your question.  So far no one has mentioned that you need to put very little if any tension on the thread as you wind.  When I teach beginners to wind a warp, I  often find that they hold the thread too tightly.  Eventually the first threads start to droop, just like in your photo.  So, yes, wind small bouts, but next time, let the thread flow through your hand without pinching it so much.  As you wind faster, you will find that you will naturally not hold it so tightly.

Joanne

jemwork (not verified)

this subject should get printed out.

Strength of dowels, angles, tension, different ways to consider the questions. I love my warping reel; I'd need a lesson on a board. there's always more to learn and share.

Thank you all... Joan

Halcyon (not verified)

Mary, I agree with Joanne about the tension as you're winding. One thing I suggest when you want an even tension is to run the yarn through a tube and then hold the tube in your hand rather than the yarn itself. I find that tends to make the tensioning more even as your fingers can add more or less tension depending on your mood, skin humidity, and how long you've been warping. When you want to wind horizontally off a cone there is a device called a Yarn Bobbin & Cone Holder that will hold either tubes or with an insert it will hold cones as well to keep them from flopping.

Halcyon - Halcyon Yarn

Submitted by Anonymous (not verified) on